DNDmitry Rudolfovich Nizin

Dmitry Rudolfovich Nizin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmitry Rudolfovich Nizin has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    «Большие данные» при прогнозировании климатической стойкости строительных материалов. Актинометрические показатели

    by Татьяна Низина, Владимир Селяев, Дмитрий Низин, Игорь Чибулаев, Илья Спирин, Николай Пивкин

    В статье приведены результаты анализа актинометрических показателей, в частности, интенсивности солнечной радиации и ультрафиолетовых излучений диапазонов A и B. Рассмотрено распределение актинометрических показателей в зависимости от дня, месяца и года (2015–2022) для умеренно континентального климата (г. Саранск). Проведено сравнение рассчитанных значений суммарной солнечной радиации, полученных с помощью станции автоматического контроля, а также показателей, представленных в ГОСТ 16350-80 для умеренного климатического района (г. Москва). Проведён анализ распределения интенсивности солнечной радиации в трёх вариантах: данные только за дневной период и гражданские сумерки (вариант 1); данные без учёта ночного периода (вариант 2); все фиксируемые с частотой в 10 мин. показатели. Установлено, что несмотря на значительную протяжённость ночного и сумеречных периодов, среднее годовое снижение суммарной солнечной радиации составляет 1,3% (вариант 1) и 0,8% (вариант 2). Исходя из малых значений поправок актинометрических показателей, учитывающих продолжительность астрономических и гражданских сумерек, при разработке моделей машинного обучения принято решение использовать все фик-сируемые с частотой в 10 мин. значения интенсивностей солнечной радиации и ультрафиолетовых излучений диапазонов A и B.

  • Accounting for the moisture state of polymeric materials when developing machine learning models

    by D. R. Nizin, T. A. Nizina, V. P. Selyaev, I. P. Spirin

    The paper provides the results of studying the dependence of elastic-strength properties of unfilled epoxy polymers on moisture content by example of 18 different compounds. It includes the analysis of possible effects associated with changes in free moisture content in the polymer matrix structure, including a change in nature of behavior under load from brittle to viscous with a multiple increase in relative deformations at rupture, as well as quasi-embrittlement, manifested in the elimination or reduction of forced highly elastic deformations on the deformation curve. In addition to the shape corresponding to the one close to linear dependence of the change in tensile strength and modulus of elasticity on moisture content with a maximum around W~0%, the study revealed other forms of interrelation of parameters under consideration: with a local maximum of values in the “optimal moisture content” area differing from W~0%; with “plateau” sections around both extreme humidity conditions. The similarity of the effects occurring around moisture content of W~0% for epoxy polymer samples both in the control state and after prolonged climatic aging is shown. A hypothesis was formulated regarding the existence of a pattern common to epoxy polymers of change in the nature of the dependence of mechanical strength on moisture content during field climatic aging. Based on a joint analysis of the dependence curves of elastic-strength parameters on moisture content, the most representative epoxy polymer compounds for field studies were selected to compile training datasets for a machine learning model predicting changes in the elastic-strength properties of polymer materials exposed to environmental factors.


  • Open Access

    Moisture absorption of 3D-printed PETG plastic samples

    by Dmitrij R. Nizin, Tat’yAna A. Nizina, Anna V. Mar’yAnova, Evgenij B. Mironov

    Introduction. The additive manufacturing method implies the emergence of emergent properties in the final product, not inherent in the original elements of the system individually. Performance properties of products obtained by FDM-printing are defined not only by the material properties, but also by printing parameters — nozzle and table temperature, layer thickness, printing speed, the direction of laying layers, their relative positioning, etc. Thus, when designing 3D-printed polymer products with the required characteristics one should consider the material – printing parameters system together. The results of the study of the effect of sorption characteristics of 3D-printed PETG plastic samples made by FDM-printing on their elastic-strength properties are presented. Materials and methods. Three groups of FDM-printed PETG 3D specimens were studied. Collection, preprocessing, analysis, statistical processing and visualization of the data were performed using Python programming language in an interactive Jupyter Notebook development environment. Results. It was found that the moisture content of 3D-printed polymer samples could be conventionally divided into the superstructural and microstructural levels. A comparison of moisture content limits in different moisture saturation conditions shows that the former exceeds the latter by 2 to 6 times depending on the specimen printing parameters. Moisture content of superstructure level has no statistically significant (for α = 0.01) effect on the ultimate tensile strength of the samples, regardless of the printing parameters of the samples. The moisture sorbed by the level of substructure presumably can act as a stress concentrator preventing the free flow of specimens beyond the ultimate tensile strength, which is reflected in the reduction of elongation at rupture. Conclusions. The obtained results allow taking into account the influence of moisture state on the elastic-strength properties of 3D printed articles and structures on the basis of PETG-plastics. This, in its turn, contributes to more accurate prediction of their behavior under real operating conditions.


  • Big Data in Predicting the Climatic Resistance of Building Materials. I. Air Temperature and Humidity

    by Т.а. Низина, Д.р. Низин, В.п. Селяев, И.п. Спирин, А.с. Станкевич

    в статье проведен сравнительный анализ количественных значений температуры и относительной влажности окружающего воздуха, рассчитанных согласно ГОСТ 16350-80 для умеренно континентального климата (представительный пункт – г. Москва), и полученных на метеорологической станции НИ МГУ им. Н.П. Огарева (г. Саранск) за период с 2015 по 2022 гг. Установлено существенное расхождение расчетных и накопленных значения метеорологических факторов. На исследуемом временном отрезке разброс значений разницы между расчетными и накопленными значениями составил от -5,8 до 10 оС для температуры воздуха и от -36,4 до 32,5% для относительной влажности. Также наблюдается существенное варьирование значений разницы исследуемых показателей в зависимости от календарного месяца и отклонение ряда кривых распределения от нормального вида, что, в целом, свидетельствует о невозможности достоверной оценки распределений с помощью только значения квадратичного отклонения, рекомендуемой ГОСТ 16350-80. Установлено, что использование расчетных распределений практически не позволяет учитывать события, возникающие вблизи границ распределений исследуемых метеорологических параметров. Это, в свою очередь, необратимо сказывается на точности прогнозирования процессов климатического старения строительных материалов. При прогнозировании климатической стойкости материалов методами машинного обучения предложено использовать вместо относительной влажности значения абсолютной влажности воздуха, как признака, имеющего четкий физический смысл (масса водяных паров, содержащихся в 1 м³ воздуха), а также определенного только на интервале неотрицательных значений. Ключевые слова: большие данные, климатическая стойкость, температура воздуха, относительная влажность, абсолютная влажность, тепловая карта, умеренно континентальный климат the article provides a comparative analysis of the quantitative values of temperature and relative humidity of the ambient air calculated according to GOST 16350-80 for a moderate continental climate (representative location – Moscow), and obtained at the meteorological station of Ogarev State University (Saransk) for the period from 2015 to 2022. A significant discrepancy between the calculated and accumulated values of meteorological factors has been established. In the studied time interval, the spread of the difference between the calculated and accumulated values ranged from -5.8 to 10 oC for air temperature and from -36.4 to 32.5% for relative humidity. There is also a significant variation in the difference of the studied indicators depending on the calendar month, as well as a deviation of a number of distribution curves from the normal form, which, in general, indicates the impossibility to reliably assess distributions using only the value of the quadratic deviation recommended by GOST 16350-80. It has been established that the use of calculated distributions virtually does not allow taking into account events occurring near the boundaries of the distributions of the studied meteorological parameters. This, in turn, irreversibly affects the accuracy of forecasting the climatic aging of building materials. When predicting the climatic resistance of materials by machine learning methods, it is proposed to use absolute humidity values instead of relative humidity as a sign that has a clear physical meaning (mass of water vapor contained in 1 m3 of air), as well as defined only in the range of non-negative values.


  • HE MAIN ADVANTAGES OF USING SENSORS TO CONTROL THE TEMPERATURE AND HUMIDITY OF THE SURFACES OF BUILDING STRUCTURES

    by Dmitry Rudolfovich Nizin, Tatiana Anatolyevna Nizina, Ilya Petrovich Spirin, Svetlana Vasilyevna Parshina

    Развитие направления информационного моделирования при проектировании зданий и сооружений с каждым годом становится все более актуальным. При этом все чаще возникает необходимость фиксации разнообразных показателей поведения строительных конструкций, а также воздействующих на них факторов, в том числе на этапе эксплуатации. На сегодняшний день существует множество технологий, с помощью которых можно отслеживать изменение различных показателей (освещенность, температура, влажность, степень нагрузки на конструкцию, степень повреждения различных частей здания и т.д.), варьирующихся в зависимости условий эксплуатации. Наиболее перспективным представляется совместное использование IoT («интернет вещей») в связке с информационными моделями. Именно благодаря данным технологиям мониторинга можно обеспечить наилучшее обслуживание строительных...

  • RELAXATION PROPERTIES OF POLYMER MATERIALS BASED ON EPOXY BINDERS

    by Nadezhda Sergeevna Kanaeva, Dmitry Rudolfovich Nizin, Tatiana Anatolyevna Nizina

    Исследованы релаксационные свойства полимерного материала, полученного на основе модифицированной смолы Этал-247 и отвердителя Этал-45М. Рассчитаны параметры кривых релаксации напряжения с аппроксимацией уравнением Кольрауша и ядрами релаксации и уравнения Больцмана. Проведено сравнение коэффициентов корреляции Пирсона исследуемых уравнений и выявлена наилучшая математическая модель для описания релаксационных процессов в полимерных...