Craig G. Moe
Craig G. Moe has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Roy H. Olsson
University of Pennsylvania
6 shared publications Ramakrishna Vetury
Akoustis Technologies Inc., Huntersville, NC, USA
4 shared publicationsAbhay Kochhar
Akoustis Inc., Huntersville, NC, USA
3 shared publicationsGregory A. Garrett
Sensors and Electron Devices Directorate, U.S. Army Research Laboratory, 2800 Powder Mill Rd., MD 20783 Adelphi, USA
3 shared publicationsHongen Shen
U.S. Army Research Laboratory 1 , Sensors and Electron Devices Directorate, 2800 Powder Mill Road, Adelphi, Maryland 20783, USA
3 shared publicationsJames R. Grandusky
Crystal IS, Inc. 70 Cohoes Ave. Green Island NY 12183 USA
3 shared publications
Latest Publications
- 27 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1470-1473
A High-Selectivity 11.9-GHz Filter Realized in a Periodically Poled Piezoelectric AlScN Film
This letter presents a highly selective bulk acoustic wave (BAW) filter operating at 11.9 GHz, fabricated with periodically poled piezoelectric film (P3F) aluminum scandium nitride (AlScN) technology. The metric used in determining selectivity is the 20-dB shape factor, defined as the ratio of the 20-dB to 3-dB filter bandwidth (BW). With a 20-dB shape factor of 1.71 and a minimum insertion loss (IL) of 1.5 dB, this filter is suitable for RF filtering applications that require efficient spectrum utilization or mitigation of near band interference.
- 27 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1470-1473
A High-Selectivity 11.9-GHz Filter Realized in a Periodically Poled Piezoelectric AlScN Film
This letter presents a highly selective bulk acoustic wave (BAW) filter operating at 11.9 GHz, fabricated with periodically poled piezoelectric film (P3F) aluminum scandium nitride (AlScN) technology. The metric used in determining selectivity is the 20-dB shape factor, defined as the ratio of the 20-dB to 3-dB filter bandwidth (BW). With a 20-dB shape factor of 1.71 and a minimum insertion loss (IL) of 1.5 dB, this filter is suitable for RF filtering applications that require efficient spectrum utilization or mitigation of near band interference.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (2) , 113-115
High Electromechanical Coupling Radial Extension Mode Resonators Realized in Al 0.7 Sc 0.3 N
This work reports aluminum scandium nitride (Al1-xScxN/AlScN) (x = 0.3/Al0.7Sc0.3N) Lamb wave resonators (LWR) operating in length extensional (LE), width extensional (WE), and radial extensional (RE) modes. COMSOL Multiphysics and experimental measurements show that the RE mode achieves a much higher electromechanical coupling, kt2, when compared to the more traditionally utilized LE and WE modes. The higher kt2 is due to the constructive addition of the d31 and d32 piezoelectric coefficients due to the RE mode shape. Experimentally, the RE mode resonator achieved a kt2 of 14.1%, which was much larger than the kt2 of 9.1% and 4.8% measured for the WE and LE mode devices fabricated on the same wafer. The RE mode achieves a high Qp of 1302 measured in air yielding a figure-of-merit (FOM = kt2Qp) of 157. Based on the high kt2 and FOM, Al0.7Sc0.3N-based RE resonators show potential for applications in piezoelectric microelectromechanical filters and oscillators. 2024-0231
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 34 (2) , 113-115
High Electromechanical Coupling Radial Extension Mode Resonators Realized in Al 0.7 Sc 0.3 N
This work reports aluminum scandium nitride (Al1-xScxN/AlScN) (x = 0.3/Al0.7Sc0.3N) Lamb wave resonators (LWR) operating in length extensional (LE), width extensional (WE), and radial extensional (RE) modes. COMSOL Multiphysics and experimental measurements show that the RE mode achieves a much higher electromechanical coupling, kt2, when compared to the more traditionally utilized LE and WE modes. The higher kt2 is due to the constructive addition of the d31 and d32 piezoelectric coefficients due to the RE mode shape. Experimentally, the RE mode resonator achieved a kt2 of 14.1%, which was much larger than the kt2 of 9.1% and 4.8% measured for the WE and LE mode devices fabricated on the same wafer. The RE mode achieves a high Qp of 1302 measured in air yielding a figure-of-merit (FOM = kt2Qp) of 157. Based on the high kt2 and FOM, Al0.7Sc0.3N-based RE resonators show potential for applications in piezoelectric microelectromechanical filters and oscillators. 2024-0231
- 9 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5630-5637
A High Quality Factor, 19-GHz Periodically Poled AlScN BAW Resonator Fabricated in a Commercial XBAW Process
This article presents 19-GHz bulk acoustic wave (BAW) resonators realized in a periodically poled piezoelectric film (P3F) microfabricated in a commercial XBAW process. The polarization of the three layers comprising the P3F film are realized via a combination of as-grown (two-layer) and electrically poled (one-layer) aluminum scandium nitride (AlScN). To improve the series ( ${Q}_{s}$ ) and maximum ( ${Q}_{\max }$ ) quality factors, the device is constructed by connecting two-BAW resonators in series, which lowers the effect of the via resistance when compared with a traditional single BAW. Resonators achieved ${Q}_{\max }$ of 531 (with ${Q}_{s}$ of 348 and ${Q}_{p}$ of 264) and ${\text {FoM}}_{{os}}$ (defined as ${\text {FoM}}_{{os}} = {{f}_{{s},{p}} {Q}}_{{s},{p}} \times {{10}}^{-{9}}$ , where ${Q}_{{s},{p}}$ is the quality factor at series ( ${f}_{s}$ ) or parallel ( ${f}_{p}$ ) resonance frequency) of 6542 at 18.8-GHz frequency, which is higher than most of the state-of-the-art piezoelectric BAW resonators operating at similar and higher frequencies. The experimental results indicate that the P3F BAW resonators are promising for applications in emerging RF communication systems.
- 9 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5630-5637
A High Quality Factor, 19-GHz Periodically Poled AlScN BAW Resonator Fabricated in a Commercial XBAW Process
This article presents 19-GHz bulk acoustic wave (BAW) resonators realized in a periodically poled piezoelectric film (P3F) microfabricated in a commercial XBAW process. The polarization of the three layers comprising the P3F film are realized via a combination of as-grown (two-layer) and electrically poled (one-layer) aluminum scandium nitride (AlScN). To improve the series ( ${Q}_{s}$ ) and maximum ( ${Q}_{\max }$ ) quality factors, the device is constructed by connecting two-BAW resonators in series, which lowers the effect of the via resistance when compared with a traditional single BAW. Resonators achieved ${Q}_{\max }$ of 531 (with ${Q}_{s}$ of 348 and ${Q}_{p}$ of 264) and ${\text {FoM}}_{{os}}$ (defined as ${\text {FoM}}_{{os}} = {{f}_{{s},{p}} {Q}}_{{s},{p}} \times {{10}}^{-{9}}$ , where ${Q}_{{s},{p}}$ is the quality factor at series ( ${f}_{s}$ ) or parallel ( ${f}_{p}$ ) resonance frequency) of 6542 at 18.8-GHz frequency, which is higher than most of the state-of-the-art piezoelectric BAW resonators operating at similar and higher frequencies. The experimental results indicate that the P3F BAW resonators are promising for applications in emerging RF communication systems.
- 3 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
X-band Bulk Acoustic Wave Resonator (XBAW) using Periodically Polarized Piezoelectric Films (P3F)
This paper demonstrates the scaling of bulk acoustic wave (BAW) resonator to create micro-acoustic RF filtering solutions in the 8 – 12 GHz range for X band applications using periodically polarized piezoelectric films (P3F). P3F BAW technology overcomes the traditional thickness frequency trade-off of single layer BAW technology. P3F BAW resonators fabricated using XBAW process in the frequency range of 8-10 GHz with FoM (${{\text{k}}_{\text{t}}}^2 \times {{\text{Q}}_{\text{p}}}$ product) of 80-120 are reported in this work.
- 3 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
X-band Bulk Acoustic Wave Resonator (XBAW) using Periodically Polarized Piezoelectric Films (P3F)
This paper demonstrates the scaling of bulk acoustic wave (BAW) resonator to create micro-acoustic RF filtering solutions in the 8 – 12 GHz range for X band applications using periodically polarized piezoelectric films (P3F). P3F BAW technology overcomes the traditional thickness frequency trade-off of single layer BAW technology. P3F BAW resonators fabricated using XBAW process in the frequency range of 8-10 GHz with FoM (${{\text{k}}_{\text{t}}}^2 \times {{\text{Q}}_{\text{p}}}$ product) of 80-120 are reported in this work.
- 19 June 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (16)
Metal–Organic Chemical Vapor Deposition‐Grown AlScN for Microelectromechanical‐Based Acoustic Filter Applications
AlScN films are produced in a commercial metal–organic chemical vapor deposition (MOCVD) system modified to low‐vapor‐pressure Sc metal–organic precursors. Growth conditions are optimized for surface morphology, film stress, and piezoelectric coefficient across a range of compositions. Epitaxial structures are designed to eliminate internal tensile stresses that develop during the film growth as well as prevent surface adatom interactions unique to the MOCVD process. From these films, wide‐bandwidth resonators and filters are manufactured using a novel microelectromechanical‐based bulk acoustic wave (BAW) transfer process. When tested on‐wafer, resonators exhibit a of 10.5%, and a value of 1400. Ladder‐type RF filters using these resonators are fabricated at 6.2 GHz and show improved performance over filters fabricated using physical vapor deposition‐deposited AlScN.
- 19 June 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (16)
Metal–Organic Chemical Vapor Deposition‐Grown AlScN for Microelectromechanical‐Based Acoustic Filter Applications
AlScN films are produced in a commercial metal–organic chemical vapor deposition (MOCVD) system modified to low‐vapor‐pressure Sc metal–organic precursors. Growth conditions are optimized for surface morphology, film stress, and piezoelectric coefficient across a range of compositions. Epitaxial structures are designed to eliminate internal tensile stresses that develop during the film growth as well as prevent surface adatom interactions unique to the MOCVD process. From these films, wide‐bandwidth resonators and filters are manufactured using a novel microelectromechanical‐based bulk acoustic wave (BAW) transfer process. When tested on‐wafer, resonators exhibit a of 10.5%, and a value of 1400. Ladder‐type RF filters using these resonators are fabricated at 6.2 GHz and show improved performance over filters fabricated using physical vapor deposition‐deposited AlScN.
- 1 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1196-1199
A K-Band Bulk Acoustic Wave Resonator Using Periodically Poled Al0.72Sc0.28N
This paper presents a K-band bulk acoustic wave (BAW) resonator constructed from an Al 0.72 Sc 0.28 N periodically poled piezoelectric film. The resonators exhibited dominant resonance responses around 20 GHz, approximately four times higher than the resonance frequencies of similar unpoled devices fabricated on the same wafer. Resonators with a quality factor ( Qp ) of 160 and an electromechanical coupling ( k 2 t ) of 8.23% were achieved. The figure of merits (defined as FoMI = k 2 t Qp and FoMII = fp FoMI ×10 -9 ) of the resonator are 13.2 and 274 which are higher than most reported acoustic resonators operating at K-band (18 GHz to 27 GHz) or higher frequency. The experimental results suggest that periodically poled BAW resonators are promising for emerging RF filter and oscillator applications at K-band frequencies.
- 1 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1196-1199
A K-Band Bulk Acoustic Wave Resonator Using Periodically Poled Al0.72Sc0.28N
This paper presents a K-band bulk acoustic wave (BAW) resonator constructed from an Al 0.72 Sc 0.28 N periodically poled piezoelectric film. The resonators exhibited dominant resonance responses around 20 GHz, approximately four times higher than the resonance frequencies of similar unpoled devices fabricated on the same wafer. Resonators with a quality factor ( Qp ) of 160 and an electromechanical coupling ( k 2 t ) of 8.23% were achieved. The figure of merits (defined as FoMI = k 2 t Qp and FoMII = fp FoMI ×10 -9 ) of the resonator are 13.2 and 274 which are higher than most reported acoustic resonators operating at K-band (18 GHz to 27 GHz) or higher frequency. The experimental results suggest that periodically poled BAW resonators are promising for emerging RF filter and oscillator applications at K-band frequencies.
- Open Access
- 3 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (17)
Growth-microstructure-thermal property relations in AlN thin films
AlN thin films are enabling significant progress in modern optoelectronics, power electronics, and microelectromechanical systems. The various AlN growth methods and conditions lead to different film microstructures. In this report, phonon scattering mechanisms that impact the cross-plane (κz; along the c-axis) and in-plane (κr; parallel to the c-plane) thermal conductivities of AlN thin films prepared by various synthesis techniques are investigated. In contrast to bulk single crystal AlN with an isotropic thermal conductivity of ∼330 W/m K, a strong anisotropy in the thermal conductivity is observed in the thin films. The κz shows a strong film thickness dependence due to phonon-boundary scattering. Electron microscopy reveals the presence of grain boundaries and dislocations that limit the κr. For instance, oriented films prepared by reactive sputtering possess lateral crystalline grain sizes ranging from 20 to 40 nm that significantly lower the κr to ∼30 W/m K. Simulation results suggest that the self-heating in AlN film bulk acoustic resonators can significantly impact the power handling capability of RF filters. A device employing an oriented film as the active piezoelectric layer shows an ∼2.5× higher device peak temperature as compared to a device based on an epitaxial film.
- 3 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (17)
Open AccessGrowth-microstructure-thermal property relations in AlN thin films
AlN thin films are enabling significant progress in modern optoelectronics, power electronics, and microelectromechanical systems. The various AlN growth methods and conditions lead to different film microstructures. In this report, phonon scattering mechanisms that impact the cross-plane (κz; along the c-axis) and in-plane (κr; parallel to the c-plane) thermal conductivities of AlN thin films prepared by various synthesis techniques are investigated. In contrast to bulk single crystal AlN with an isotropic thermal conductivity of ∼330 W/m K, a strong anisotropy in the thermal conductivity is observed in the thin films. The κz shows a strong film thickness dependence due to phonon-boundary scattering. Electron microscopy reveals the presence of grain boundaries and dislocations that limit the κr. For instance, oriented films prepared by reactive sputtering possess lateral crystalline grain sizes ranging from 20 to 40 nm that significantly lower the κr to ∼30 W/m K. Simulation results suggest that the self-heating in AlN film bulk acoustic resonators can significantly impact the power handling capability of RF filters. A device employing an oriented film as the active piezoelectric layer shows an ∼2.5× higher device peak temperature as compared to a device based on an epitaxial film.
- 6 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 31 (4) , 604-611
Controlling Residual Stress and Suppression of Anomalous Grains in Aluminum Scandium Nitride Films Grown Directly on Silicon
Deposition of Aluminum Scandium Nitride (AlScN) films directly on Silicon at high Sc alloying levels, with controlled stress, and free of anomalous grains (AOGs) is demonstrated using reactive co-sputtering. The average stress and AOG formation consider the Sc alloying range between 20.3 and 36.6 atomic % and for film thicknesses from 400 nm to 1000 nm for 27.3% and 31.7% Sc alloying. The combination of a gradient seed layer and proper process gas mixture is shown to inhibit formation of AOGs in AlScN with up to 36% Sc alloying even when grown directly on Si. It is demonstrated that the total flow can be utilized to control the average film stress across the 20-36% doping range while the process gas mixture primarily impacts the density of AOG formation in the AlScN films. Bulk acoustic wave resonators fabricated from 380 nm and 485 nm thick low stress and AOG free Al 0.68 Sc 0.32 N films grown directly on Si demonstrate high frequency operation of 3.6 and 4.8 GHz, high electromechanical coupling >20%, and quality factors in excess of 500. [2021-0252]
- 6 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 31 (4) , 604-611
Controlling Residual Stress and Suppression of Anomalous Grains in Aluminum Scandium Nitride Films Grown Directly on Silicon
Deposition of Aluminum Scandium Nitride (AlScN) films directly on Silicon at high Sc alloying levels, with controlled stress, and free of anomalous grains (AOGs) is demonstrated using reactive co-sputtering. The average stress and AOG formation consider the Sc alloying range between 20.3 and 36.6 atomic % and for film thicknesses from 400 nm to 1000 nm for 27.3% and 31.7% Sc alloying. The combination of a gradient seed layer and proper process gas mixture is shown to inhibit formation of AOGs in AlScN with up to 36% Sc alloying even when grown directly on Si. It is demonstrated that the total flow can be utilized to control the average film stress across the 20-36% doping range while the process gas mixture primarily impacts the density of AOG formation in the AlScN films. Bulk acoustic wave resonators fabricated from 380 nm and 485 nm thick low stress and AOG free Al 0.68 Sc 0.32 N films grown directly on Si demonstrate high frequency operation of 3.6 and 4.8 GHz, high electromechanical coupling >20%, and quality factors in excess of 500. [2021-0252]
- 20 December 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (10)
AlGaN Light‐Emitting Diodes on AlN Substrates Emitting at 230 nm
Light‐emitting diodes with emission wavelengths between 230 and 240 nm are grown on AlN substrates and characterized optically and electrically. Optimized doping of the n‐AlGaN with Si has resulted in a mean forward voltage at 200 mA of 9 V. The electroluminescence spectra is demonstrated to be free of long wavelength parasitic emission. An envelope function in the output power versus peak wavelength is shown, demonstrating the increasing dominance of in‐plane emission at shorter wavelengths as light extraction becomes more difficult. However, variations in device structure show that further optimization of the structure for carrier confinement and injection efficiency are also able to push performance beyond the current state of the art.
- 20 December 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (10)
AlGaN Light‐Emitting Diodes on AlN Substrates Emitting at 230 nm
Light‐emitting diodes with emission wavelengths between 230 and 240 nm are grown on AlN substrates and characterized optically and electrically. Optimized doping of the n‐AlGaN with Si has resulted in a mean forward voltage at 200 mA of 9 V. The electroluminescence spectra is demonstrated to be free of long wavelength parasitic emission. An envelope function in the output power versus peak wavelength is shown, demonstrating the increasing dominance of in‐plane emission at shorter wavelengths as light extraction becomes more difficult. However, variations in device structure show that further optimization of the structure for carrier confinement and injection efficiency are also able to push performance beyond the current state of the art.
- 8 March 2014
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8986, 89861V
High-power pseudomorphic mid-ultraviolet light-emitting diodes with improved efficiency and lifetime
Recent advances in mid-ultraviolet light-emitting diodes grown pseudomorphically on bulk AlN substrates have led to improved efficiencies and lifetimes. For a 266 nm device an output power of 66 mW at 300 mA has been achieved with an external quantum efficiency of 4.5%. More importantly, the lifetimes of these devices have been increased substantially. Testing of LEDs in both surface mount design (SMD) and TO-39 packages show L50 lifetimes well in excess of 1,000 hours under a variety of case temperatures and currents. Package-related catastrophic failures are eliminated through encapsulation and hermetic sealing, further reducing failure rates and extending the lifetime.
- 8 March 2014
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8986, 89861V
High-power pseudomorphic mid-ultraviolet light-emitting diodes with improved efficiency and lifetime
Recent advances in mid-ultraviolet light-emitting diodes grown pseudomorphically on bulk AlN substrates have led to improved efficiencies and lifetimes. For a 266 nm device an output power of 66 mW at 300 mA has been achieved with an external quantum efficiency of 4.5%. More importantly, the lifetimes of these devices have been increased substantially. Testing of LEDs in both surface mount design (SMD) and TO-39 packages show L50 lifetimes well in excess of 1,000 hours under a variety of case temperatures and currents. Package-related catastrophic failures are eliminated through encapsulation and hermetic sealing, further reducing failure rates and extending the lifetime.