Yoshitaka Fujita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yoshitaka Fujita has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Shun-Ichi Ikawa
Department of Chemistry, Faculty of Science, Hokkaido University, Sapporo 060, Japan
4 shared publicationsA Kumar
National Physical Laboratory (NPLI), Dr K S Krishnan Marg, 110012 New Delhi, India
1 shared publication- Andreia Furtado
IPQ, Rua António Gião 2, 2829-513 Caparica, Portugal
1 shared publication B Lugadiru
Kenya Bureau of Standards (KEBS), Popo Road, P. O. Box 54974 - 00200, Nairobi, Kenya
1 shared publicationC Buchner
Bundesamt für Eich- und Vermessungswesen (BEV), Arltgasse 35, A 1160 Wien, Austria
1 shared publicationD Jonker
National Metrology Institute of South Africa (NMISA), Meiring Naudé Road, Brummeria, Pretoria, 0184, South Africa
1 shared publication
Latest Publications
- 25 August 2020
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 31 (11) , 115302
Design of a high-pressure viscosity-measurement system using two pressure balances
In this paper, a new high-pressure viscosity measurement system using a capillary method is reported. In this system, two pressure balances are used to generate stable pressure and flow field in the capillary. The volumetric flow rate was measured by calculating the change in the piston fall rate. To check the effectiveness of the method, the viscosity of bis(2-ethylhexyl) sebacate was measured at pressures of up to 200 MPa. Differential pressure and volumetric flow rate had a linear relationship at all temperature and pressure conditions, indicating that the Hagen–Poiseuille law can be applied in this method. The viscosity–pressure dependence is in agreement with other published reports. Thus, we confirmed that the newly developed high-pressure viscosity measurement system can accurately evaluate the pressure dependence of viscosity.
- 25 August 2020
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 31 (11) , 115302
Design of a high-pressure viscosity-measurement system using two pressure balances
In this paper, a new high-pressure viscosity measurement system using a capillary method is reported. In this system, two pressure balances are used to generate stable pressure and flow field in the capillary. The volumetric flow rate was measured by calculating the change in the piston fall rate. To check the effectiveness of the method, the viscosity of bis(2-ethylhexyl) sebacate was measured at pressures of up to 200 MPa. Differential pressure and volumetric flow rate had a linear relationship at all temperature and pressure conditions, indicating that the Hagen–Poiseuille law can be applied in this method. The viscosity–pressure dependence is in agreement with other published reports. Thus, we confirmed that the newly developed high-pressure viscosity measurement system can accurately evaluate the pressure dependence of viscosity.
- 1 January 2018
- Published by IOP Publishing in Metrologia
- Vol. 55 (1A) , 07010
CCM.V-K3: CCM Key Comparison of Viscosity
This report describes the third CCM key comparison in capillary viscometry at twelve National Metrology Institutes (NMIs), which was carried out between October 2012 and February 2013. Seven NMIs, which do not maintain an independent viscosity scale, also took part in this comparison. Three samples of Newtonian liquids with nominal kinematic viscosities of 6 mm²/s at 15 °C and 5 mm²/s at 20 °C, 2000 mm²/s at 20 °C and 500 mm²/s at 40 °C, and 160000 mm²/s at 20 °C and 25000 mm²/s at 40 °C prepared by NMIJ were provided to each of the NMIs. For each of these liquids at two temperatures, total number of 98 measurements was carried out and from the results of viscosity measurements, the key comparison reference values (KCRVs) for six data sets were determined. The degrees of equivalences was evaluated by difference from the KCRV and, with a few exceptions, these differences were almost equal to or less than expanded uncertainties, showing a good equivalencies of capabilities at the participating NMIs for the viscosity measurements in wide range of viscosities covered from 5 mm²/s to 160000 mm²/s. KEY WORDS FOR SEARCH Main text To reach the main text of this paper, click on Final Report . Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/ . The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).
- 1 January 2018
- Published by IOP Publishing in Metrologia
- Vol. 55 (1A) , 07010
CCM.V-K3: CCM Key Comparison of Viscosity
This report describes the third CCM key comparison in capillary viscometry at twelve National Metrology Institutes (NMIs), which was carried out between October 2012 and February 2013. Seven NMIs, which do not maintain an independent viscosity scale, also took part in this comparison. Three samples of Newtonian liquids with nominal kinematic viscosities of 6 mm²/s at 15 °C and 5 mm²/s at 20 °C, 2000 mm²/s at 20 °C and 500 mm²/s at 40 °C, and 160000 mm²/s at 20 °C and 25000 mm²/s at 40 °C prepared by NMIJ were provided to each of the NMIs. For each of these liquids at two temperatures, total number of 98 measurements was carried out and from the results of viscosity measurements, the key comparison reference values (KCRVs) for six data sets were determined. The degrees of equivalences was evaluated by difference from the KCRV and, with a few exceptions, these differences were almost equal to or less than expanded uncertainties, showing a good equivalencies of capabilities at the participating NMIs for the viscosity measurements in wide range of viscosities covered from 5 mm²/s to 160000 mm²/s. KEY WORDS FOR SEARCH Main text To reach the main text of this paper, click on Final Report . Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/ . The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).
- 10 June 2014
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 115 (22) , 223509
Mechanisms for three kinds of limiting shear stresses appearing in the traction modes of viscous, viscoelastic, and glassy states of lubricants
We present that the tractional flow of a lubricant shows three kinds of limiting shear stresses at which the shear stresses take place independently of the shear rates in its viscous, viscoelastic, and glassy states. We propose three models on the mechanisms for the limiting shear stresses, based on the data of Brillouin spectra and viscosity of viscoelastic liquids previously reported by us and based on the data of the deformation of glassy polymers referred from others. The Brillouin spectra of a viscoelastic lubricant measured at up to 5 GPa at 25 and 80 °C show that we could not observe a frequency dispersion in sound waves below 0.8 GPa at 80 °C, while we can observe the frequency dispersion above 0.1 MPa at 25 °C owing to the viscosity of the lubricant. This result predicts the viscous limiting shear stress in the viscous state owing to the disappearance of meso-structures by heating and shearing under pressure. The viscosity of a polymer measured around the glass transition temperature (Tg) shows that Tg determined by the viscosity measurement is 27 K lower than that determined by calorimetry. This result predicts the elastic limiting shear stress in the viscoelastic state near the glass transition pressure (Pg) owing to the shear thinning effect by shearing a lubricant film. In addition, there is the plastic limiting shear stress in the glassy state owing to the yield stress at which the tractional flow of a glassy lubricant behaves as a plastic solid.
- 10 June 2014
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 115 (22) , 223509
Mechanisms for three kinds of limiting shear stresses appearing in the traction modes of viscous, viscoelastic, and glassy states of lubricants
We present that the tractional flow of a lubricant shows three kinds of limiting shear stresses at which the shear stresses take place independently of the shear rates in its viscous, viscoelastic, and glassy states. We propose three models on the mechanisms for the limiting shear stresses, based on the data of Brillouin spectra and viscosity of viscoelastic liquids previously reported by us and based on the data of the deformation of glassy polymers referred from others. The Brillouin spectra of a viscoelastic lubricant measured at up to 5 GPa at 25 and 80 °C show that we could not observe a frequency dispersion in sound waves below 0.8 GPa at 80 °C, while we can observe the frequency dispersion above 0.1 MPa at 25 °C owing to the viscosity of the lubricant. This result predicts the viscous limiting shear stress in the viscous state owing to the disappearance of meso-structures by heating and shearing under pressure. The viscosity of a polymer measured around the glass transition temperature (Tg) shows that Tg determined by the viscosity measurement is 27 K lower than that determined by calorimetry. This result predicts the elastic limiting shear stress in the viscoelastic state near the glass transition pressure (Pg) owing to the shear thinning effect by shearing a lubricant film. In addition, there is the plastic limiting shear stress in the glassy state owing to the yield stress at which the tractional flow of a glassy lubricant behaves as a plastic solid.
- 1 August 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (3) , 033538
Dispersion and attenuation on the Brillouin sound waves of a lubricant: Di(2-ethylhexyl) sebacate under high pressures
The Brillouin spectra of di(2-ethylhexyl) sebacate, which is a liquid lubricant known as DOS, were measured at up to 5 GPa at 25 °C and up to 2.5 GPa at 80 °C. At 25 °C, the Brillouin frequency linewidth (acoustic attenuation) has a large maximum at 0.1 MPa, and at 80 °C, it has a large broad maximum at 0.8 GPa. The Brillouin frequency shift (sound velocity) and linewidth obtained indicate that the large dispersion of the sound velocities of DOS occurs from 0.1 MPa at 25 °C and from 0.8 GPa at 80 °C. The origins of this attenuation and dispersion are discussed on the basis of the theory for a viscoelastic liquid. It is proposed that the large acoustic attenuation and dispersion of DOS are due to the production of higher-rank structures with nano-order domains in a polymeric liquid by pressurization. The results show that DOS is strongly viscoelastic above 0.8 GPa at 80 °C, but it is not viscous below 0.8 GPa at 80 °C, with the disappearance of the frequency dispersion. The result obtained is used to explain a limiting shear stress observed in a traction oil. Above a given sliding speed, the oil reaches the region of temperature and pressure in which its viscosity decreases with increasing shear rate and conveys a constant torque above some high shear rate. Then, the oil flows as a plastic solid at a limiting shear stress. These findings regarding the dynamical properties of DOS under high pressures are very useful for the production and analysis of lubricants and traction oils.
- 1 August 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (3) , 033538
Dispersion and attenuation on the Brillouin sound waves of a lubricant: Di(2-ethylhexyl) sebacate under high pressures
The Brillouin spectra of di(2-ethylhexyl) sebacate, which is a liquid lubricant known as DOS, were measured at up to 5 GPa at 25 °C and up to 2.5 GPa at 80 °C. At 25 °C, the Brillouin frequency linewidth (acoustic attenuation) has a large maximum at 0.1 MPa, and at 80 °C, it has a large broad maximum at 0.8 GPa. The Brillouin frequency shift (sound velocity) and linewidth obtained indicate that the large dispersion of the sound velocities of DOS occurs from 0.1 MPa at 25 °C and from 0.8 GPa at 80 °C. The origins of this attenuation and dispersion are discussed on the basis of the theory for a viscoelastic liquid. It is proposed that the large acoustic attenuation and dispersion of DOS are due to the production of higher-rank structures with nano-order domains in a polymeric liquid by pressurization. The results show that DOS is strongly viscoelastic above 0.8 GPa at 80 °C, but it is not viscous below 0.8 GPa at 80 °C, with the disappearance of the frequency dispersion. The result obtained is used to explain a limiting shear stress observed in a traction oil. Above a given sliding speed, the oil reaches the region of temperature and pressure in which its viscosity decreases with increasing shear rate and conveys a constant torque above some high shear rate. Then, the oil flows as a plastic solid at a limiting shear stress. These findings regarding the dynamical properties of DOS under high pressures are very useful for the production and analysis of lubricants and traction oils.
- 24 March 2009
- Published by IOP Publishing in Metrologia
- Vol. 46 (3) , 237-248
Evaluation of uncertainty in viscosity measurements by capillary master viscometers
- 24 March 2009
- Published by IOP Publishing in Metrologia
- Vol. 46 (3) , 237-248
Evaluation of uncertainty in viscosity measurements by capillary master viscometers
- 8 December 1995
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 103 (22) , 9580-9588
Molecular dynamics study of liquid carbon disulfide and benzene: Effect of pressure on the far-infrared collision-induced absorption
We have performed molecular dynamics calculations of liquid carbon disulfide and liquid benzene, intending to examine the effect of pressure on the far-infrared collision-induced absorption as well as on the local structure and on the molecular reorientational dynamics. The calculations reproduced well the experimental results of the reorientational correlation times of liquid carbon disulfide at pressures, of the reorientational anisotropy of liquid benzene, and of the density dependence of the collision-induced dipole moments and their time derivatives of both liquids. Contributions of various interaction terms to the collision-induced dipole moments were examined as a function of density. The experimental results that the collision-induced dipole moments of liquid benzene decreases and those of liquid carbon disulfide changes little with increase in density are explained well by pressure-dependent change in degree of the cancellation between the positive two-molecule interaction term and the negative three-molecule interaction terms.
- 8 December 1995
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 103 (22) , 9580-9588
Molecular dynamics study of liquid carbon disulfide and benzene: Effect of pressure on the far-infrared collision-induced absorption
We have performed molecular dynamics calculations of liquid carbon disulfide and liquid benzene, intending to examine the effect of pressure on the far-infrared collision-induced absorption as well as on the local structure and on the molecular reorientational dynamics. The calculations reproduced well the experimental results of the reorientational correlation times of liquid carbon disulfide at pressures, of the reorientational anisotropy of liquid benzene, and of the density dependence of the collision-induced dipole moments and their time derivatives of both liquids. Contributions of various interaction terms to the collision-induced dipole moments were examined as a function of density. The experimental results that the collision-induced dipole moments of liquid benzene decreases and those of liquid carbon disulfide changes little with increase in density are explained well by pressure-dependent change in degree of the cancellation between the positive two-molecule interaction term and the negative three-molecule interaction terms.
- 8 September 1995
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 103 (10) , 3907-3911
High-pressure study of the far-infrared collision-induced absorption of nondipolar liquids
Far‐infrared collision‐induced absorption of liquid benzene, hexafluorobenzene, and 1,3,5‐trifluoro‐ benzene were measured at pressures and room temperature with a synchrotron radiationsource. The zeroth and second spectral moments of the absorption bands were obtained as a function of pressure. The collision‐induced dipole moments and their time derivatives were obtained from the spectral moments for these liquids and previously measuredcarbon disulfide and carbon tetrachloride. The induced‐dipole moments decrease with increasing pressure for the liquids studied except carbon disulfide for which the moment is nearly independent of pressure. This decrease in the moments is probably caused by increase in the cancellation effect of three‐molecule correlation with an increase in pressure. The time derivatives of the collision‐induced moments, on the other hand, increase with increasing pressure. This is explained by increase in collision frequencies with pressure.
- 8 September 1995
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 103 (10) , 3907-3911
High-pressure study of the far-infrared collision-induced absorption of nondipolar liquids
Far‐infrared collision‐induced absorption of liquid benzene, hexafluorobenzene, and 1,3,5‐trifluoro‐ benzene were measured at pressures and room temperature with a synchrotron radiationsource. The zeroth and second spectral moments of the absorption bands were obtained as a function of pressure. The collision‐induced dipole moments and their time derivatives were obtained from the spectral moments for these liquids and previously measuredcarbon disulfide and carbon tetrachloride. The induced‐dipole moments decrease with increasing pressure for the liquids studied except carbon disulfide for which the moment is nearly independent of pressure. This decrease in the moments is probably caused by increase in the cancellation effect of three‐molecule correlation with an increase in pressure. The time derivatives of the collision‐induced moments, on the other hand, increase with increasing pressure. This is explained by increase in collision frequencies with pressure.
- 1 November 1991
- Published by Canadian Science Publishing in Canadian Journal of Chemistry
- Vol. 69 (11) , 1745-1751
Measurements of far-infrared optical constants of liquids with a synchrotron radiation source
The far-infrared optical constants of liquid acetonitrile, carbon disulfide, and carbon tetrachloride were determined from transmission measurements with a synchrotron radiation source at the Institute for Molecular Science (Okazaki). The small size of the synchrotron radiation source was of benefit to measurements of transmittances that were suited for an analysis based on an optical theory. From the transmittances of liquid acetonitrile at temperatures ranging from 238 to 343 K, both the absorption coefficients and the refractive indices were obtained by using the subtractive Kramers–Kronig relation proposed by Jones and co-workers. The dipole moment of liquid acetonitrile calculated from the optical constants, 4.5 ± 0.1 D, is nearly independent of temperature. The spectra of carbon disulfide and carbon tetrachloride were measured at pressures in the ranges 1–1800 bar and 1–1100 bar, respectively. The absorption coefficients were obtained from the transmittances by neglecting the dispersion of the refractive indices. The zeroth and second moments of the collision-induced absorption bands were obtained as a function of pressure, after resolving the overlap of intramolecular vibrational bands. Key words: far-infrared, optical constants, pressure, liquid, synchrotron radiation source.
- 1 November 1991
- Published by Canadian Science Publishing in Canadian Journal of Chemistry
- Vol. 69 (11) , 1745-1751
Measurements of far-infrared optical constants of liquids with a synchrotron radiation source
The far-infrared optical constants of liquid acetonitrile, carbon disulfide, and carbon tetrachloride were determined from transmission measurements with a synchrotron radiation source at the Institute for Molecular Science (Okazaki). The small size of the synchrotron radiation source was of benefit to measurements of transmittances that were suited for an analysis based on an optical theory. From the transmittances of liquid acetonitrile at temperatures ranging from 238 to 343 K, both the absorption coefficients and the refractive indices were obtained by using the subtractive Kramers–Kronig relation proposed by Jones and co-workers. The dipole moment of liquid acetonitrile calculated from the optical constants, 4.5 ± 0.1 D, is nearly independent of temperature. The spectra of carbon disulfide and carbon tetrachloride were measured at pressures in the ranges 1–1800 bar and 1–1100 bar, respectively. The absorption coefficients were obtained from the transmittances by neglecting the dispersion of the refractive indices. The zeroth and second moments of the collision-induced absorption bands were obtained as a function of pressure, after resolving the overlap of intramolecular vibrational bands. Key words: far-infrared, optical constants, pressure, liquid, synchrotron radiation source.
- 1 July 1989
- Published by Elsevier in Chemical Physics Letters
- Vol. 159 (2-3) , 184-188
Effect of temperature on the hydrogen bond distribution in water as studied by infrared spectra
- 1 July 1989
- Published by Elsevier in Chemical Physics Letters
- Vol. 159 (2-3) , 184-188
Effect of temperature on the hydrogen bond distribution in water as studied by infrared spectra