Anshuman Kumar
Research Subjects
Research Interests
Anshuman Kumar has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
Chandramani Upadhyay
Centre for Advanced Studies, Dr. A.P.J. Abdul Kalam Technical University, Lucknow, India
4 shared publications- Kumar Abhishek
IITRAM
4 shared publications K. Vivekananda
ICFAI Foundation for Higher Education
3 shared publications- Kalipada Maity
National Institute of Technology
2 shared publications Rajiv Kumar Yadav
Ashoka Institute of Technology and Management
2 shared publicationsVivekananda Kukkala
ICFAI Foundation for Higher Education
2 shared publications
Latest Publications
- 2 February 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (2) , 147
Enhancing corner accuracy and machining quality in wire-EDM of In(690) using recirculating molybdenum wire: a hybrid machine learning and metaheuristic optimization approach
- 2 February 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (2) , 147
Enhancing corner accuracy and machining quality in wire-EDM of In(690) using recirculating molybdenum wire: a hybrid machine learning and metaheuristic optimization approach
- 1 September 2025
- Published by Springer Nature
- p. 1-16
Experimental Investigation and Hybrid Metaheuristic Optimization Using ANN-MOJAYA on Corner Accuracy During WEDM for Ti-3Al-2.5V
- 1 September 2025
- Published by Springer Nature
- p. 1-16
Experimental Investigation and Hybrid Metaheuristic Optimization Using ANN-MOJAYA on Corner Accuracy During WEDM for Ti-3Al-2.5V
- 30 July 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (6) , 4113-4121
A hybrid multi-optimization of cutting rate and surface roughness using PCA-based improved-GWO in precise CNC turning of AA2014
- 30 July 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (6) , 4113-4121
A hybrid multi-optimization of cutting rate and surface roughness using PCA-based improved-GWO in precise CNC turning of AA2014
- Open Access
- 23 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 552, 01034
Machining Performance Optimization of FSW Using ANN-based PCA - A Hybrid approach for AA6061
In this study, Friction stir welding (FSW) of AA6061 shows the importance of machining parameters such as tool rotational speed (TRS), feed rate (FR) and Tool Pressure angle (TPA). The machining performance has been measured through the ultimate tensile strength (UTS) and Vickers hardness (VH). The Taguchi’s philosophy has been considered in designing the experiment. The machining characteristics were analyzed using the main effect plot and analysis of variance (ANOVA). A principal component analysis (PCA) based composite principal component (CPC) has been used to optimise multi-response. The TRS has been found to be the most significant parameter for obtaining the optimum parameter setting. The performance has been enhanced using ANN technique of the process.
- 23 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 552, 01034
Open AccessMachining Performance Optimization of FSW Using ANN-based PCA - A Hybrid approach for AA6061
In this study, Friction stir welding (FSW) of AA6061 shows the importance of machining parameters such as tool rotational speed (TRS), feed rate (FR) and Tool Pressure angle (TPA). The machining performance has been measured through the ultimate tensile strength (UTS) and Vickers hardness (VH). The Taguchi’s philosophy has been considered in designing the experiment. The machining characteristics were analyzed using the main effect plot and analysis of variance (ANOVA). A principal component analysis (PCA) based composite principal component (CPC) has been used to optimise multi-response. The TRS has been found to be the most significant parameter for obtaining the optimum parameter setting. The performance has been enhanced using ANN technique of the process.
- Open Access
- 23 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 552, 01036
Predict the machining performance of FSW of dissimilar material of AI5052 and AZ31 using Multi-Objective Dragonfly Algorithm
In this study, two dissimilar materials (Al 5052 and AZ31) have been welded using the Friction stir process (FSW). Taguchi’s philosophy has been used to design the experiment using four input parameters (Tool types (TP), Tool traverse speed (TTS), Tool tilt angle (TTA), and Tool rotation Speed (TRS)). The machining performances have been identified using ultimate tensile strength (UTS) and Vickers hardness (HV). The models are evaluated for sufficiency, and then the most significant parameters are determined using analysis of variance (ANOVA). The ANOVA results revealed that TTS has a maximum contribution of 50.2% and 46.5% towards obtaining the high UTS and HV, respectively. The mathematical model using the non-linear model for UTS and HV has been created to predict the mechanical properties of FSWed joints. The prediction welding accuracy of a multi-objective optimization has been performed using the Multi-Objective Dragonfly Algorithm (MODA). The adopted strategy shows a high welding accuracy with minimum computational time.
- 23 July 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 552, 01036
Open AccessPredict the machining performance of FSW of dissimilar material of AI5052 and AZ31 using Multi-Objective Dragonfly Algorithm
In this study, two dissimilar materials (Al 5052 and AZ31) have been welded using the Friction stir process (FSW). Taguchi’s philosophy has been used to design the experiment using four input parameters (Tool types (TP), Tool traverse speed (TTS), Tool tilt angle (TTA), and Tool rotation Speed (TRS)). The machining performances have been identified using ultimate tensile strength (UTS) and Vickers hardness (HV). The models are evaluated for sufficiency, and then the most significant parameters are determined using analysis of variance (ANOVA). The ANOVA results revealed that TTS has a maximum contribution of 50.2% and 46.5% towards obtaining the high UTS and HV, respectively. The mathematical model using the non-linear model for UTS and HV has been created to predict the mechanical properties of FSWed joints. The prediction welding accuracy of a multi-objective optimization has been performed using the Multi-Objective Dragonfly Algorithm (MODA). The adopted strategy shows a high welding accuracy with minimum computational time.
- 27 December 2023
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 23 (02) , 305-327
Experimental Investigation and Soft Computing-based Assessment using ANN-MOGWO-A Hybrid Approach for Inconel(825)
In this paper, a strategy has been set for minimizing the corner error in the modification of pulse and non-pulse parameters. Taguchi’s philosophy has been used to design the experiment by varying process parameters (i.e. Spark-on Time (STon), Wire Tension (WT), Servo-Voltage (Sv), Discharge Current (DC) and Wire-speed (Sw)), to explore the machining outcomes. The response characteristics have been measured in terms of cutting speed (Cs), Corner Error (CD) and surface Roughness (RA) using Topas plus X wire of [ ] 0.25[ ]mm diameter. The machining performance characteristics were analyzed using main effect plots and analysis of variance (ANOVA). Furthermore, a soft computing-based hybrid optimization technique (Artifical Neural Network (ANN)-based Multi-Objective Grey Wolf Optimizer (MOGWO)) has been utilized to search the multi-optimum parameter setting for superior machining results. The most significant parameter observed is DC for Cs, which is determined to be 34.81%. Moreover, WT found 26.29% and 34.10% for CD and RA, respectively. The confirmation test shows that the maximum absolute percentage errors are observed as 3.89%, 6.3% and 9.7% for Cs, CD and RA, respectively. The proposed hybrid technique can generate superior solutions compared to the existing algorithms. Notably, the outcomes obtained on new instances exhibit potential, purposeful, and efficacy.
- 27 December 2023
- Published by World Scientific Pub Co Pte Ltd in Journal of Advanced Manufacturing Systems
- Vol. 23 (02) , 305-327
Experimental Investigation and Soft Computing-based Assessment using ANN-MOGWO-A Hybrid Approach for Inconel(825)
In this paper, a strategy has been set for minimizing the corner error in the modification of pulse and non-pulse parameters. Taguchi’s philosophy has been used to design the experiment by varying process parameters (i.e. Spark-on Time (STon), Wire Tension (WT), Servo-Voltage (Sv), Discharge Current (DC) and Wire-speed (Sw)), to explore the machining outcomes. The response characteristics have been measured in terms of cutting speed (Cs), Corner Error (CD) and surface Roughness (RA) using Topas plus X wire of [ ] 0.25[ ]mm diameter. The machining performance characteristics were analyzed using main effect plots and analysis of variance (ANOVA). Furthermore, a soft computing-based hybrid optimization technique (Artifical Neural Network (ANN)-based Multi-Objective Grey Wolf Optimizer (MOGWO)) has been utilized to search the multi-optimum parameter setting for superior machining results. The most significant parameter observed is DC for Cs, which is determined to be 34.81%. Moreover, WT found 26.29% and 34.10% for CD and RA, respectively. The confirmation test shows that the maximum absolute percentage errors are observed as 3.89%, 6.3% and 9.7% for Cs, CD and RA, respectively. The proposed hybrid technique can generate superior solutions compared to the existing algorithms. Notably, the outcomes obtained on new instances exhibit potential, purposeful, and efficacy.
- 11 October 2023
- Published by Springer Nature in Experimental Techniques
- Vol. 48 (3) , 537-558
Soft Computing Based Parametric Optimization of Cutting Rate, Surface Roughness, and Kerf Width in Wire Electric Discharge Machining of High Strength Ti-3Al-2.5 V
- 11 October 2023
- Published by Springer Nature in Experimental Techniques
- Vol. 48 (3) , 537-558
Soft Computing Based Parametric Optimization of Cutting Rate, Surface Roughness, and Kerf Width in Wire Electric Discharge Machining of High Strength Ti-3Al-2.5 V
- 20 May 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 4473-4479
Experimental investigation and parametric optimization during EDM of Titanium grade 9 using MOORA-fuzzy integrated multi-objective Genetic algorithm
- 20 May 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 4473-4479
Experimental investigation and parametric optimization during EDM of Titanium grade 9 using MOORA-fuzzy integrated multi-objective Genetic algorithm