Jian Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jian Yang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Oleg Ostrovski
University of New South Wales
6 shared publicationsYasushi Sasaki
University of New South Wales
6 shared publications- Jiaqiang Zhang
Department of Anesthesiology and Perioperative Medicine, People's Hospital of Zhengzhou University, Henan Provincial People's Hospital, Zhengzhou, Henan, China.
5 shared publications Chen Zhang
Baosteel Group Corporation Research Institute
4 shared publicationsDexiang Cai
Baosteel Group Corporation Research Institute
4 shared publicationsYoshiaki Kashiwaya
Kyoto University
4 shared publications
Latest Publications
- Open Access
- 1 January 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 10, 268-281
Gaining insights on high-temperature thermal conductivity and structure of oxide melts through experimental and molecular dynamics simulation study
- 1 January 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 10, 268-281
Open AccessGaining insights on high-temperature thermal conductivity and structure of oxide melts through experimental and molecular dynamics simulation study
- 18 May 2017
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 48 (4) , 2077-2091
Effect of B2O3 on Crystallization Behavior, Structure, and Heat Transfer of CaO-SiO2-B2O3-Na2O-TiO2-Al2O3-MgO-Li2O Mold Fluxes
- 18 May 2017
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 48 (4) , 2077-2091
Effect of B2O3 on Crystallization Behavior, Structure, and Heat Transfer of CaO-SiO2-B2O3-Na2O-TiO2-Al2O3-MgO-Li2O Mold Fluxes
- 9 July 2016
- Published by Springer Nature in Metals and Materials International
- Vol. 22 (4) , 700-706
Effect of MnO content on the interfacial property of mold flux and steel
- 9 July 2016
- Published by Springer Nature in Metals and Materials International
- Vol. 22 (4) , 700-706
Effect of MnO content on the interfacial property of mold flux and steel
- 8 June 2016
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 47 (4) , 2447-2458
Crystallization Behavior and Heat Transfer of Fluorine-Free Mold Fluxes with Different Na2O Concentration
- 8 June 2016
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 47 (4) , 2447-2458
Crystallization Behavior and Heat Transfer of Fluorine-Free Mold Fluxes with Different Na2O Concentration
- 1 January 2016
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 56 (4) , 574-583
In-situ Study of Crystallisation Behaviour of CaO–SiO2–Na2O–B2O3–TiO2–Al2O3–MgO–Li2O Fluorine-free Mould Fluxes with Different CaO/SiO2 Ratios
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 1 January 2016
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 56 (4) , 574-583
In-situ Study of Crystallisation Behaviour of CaO–SiO2–Na2O–B2O3–TiO2–Al2O3–MgO–Li2O Fluorine-free Mould Fluxes with Different CaO/SiO2 Ratios
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 18 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 662-669
Phase Equilibria of Fluoride-Free Boracic Mould Flux for Steel Continuous Casting
- 18 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 662-669
Phase Equilibria of Fluoride-Free Boracic Mould Flux for Steel Continuous Casting
- 9 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 636-643
In‐Situ Study of Crystallization Behavior of a Mold Flux Using Single and Double Hot Thermocouple Technique
In this study, crystallization behavior of an industrial mold flux was investigated using both single hot thermocouple technique (SHTT) and double hot thermocouple technique (DHTT). Continuous cooling transformation (CCT) and time‐temperature transformation (TTT) diagrams were constructed using SHTT. The critical cooling rate in continuous cooling process was determined as 7 °C s−1 above which a glassy phase was formed. The TTT diagram showed two noses at approximately 1000 and 1075 °C. Phase identification carried out using X‐ray diffraction (XRD) revealed that dicalcium silicate (Ca2SiO4) was the major phase at both 950 and 1100 °C, together with minor precipitates of Na2CaSi3O8 and Ca2MgSi2O7 whose concentrations were relatively higher at 950 °C. Cuspidine (Ca4Si2O7F2) was also identified by XRD at 950 °C. Crystallization kinetics was analyzed using Johnson–Mehl–Avrami–Kolmogorov equation. DHTT was used to simulate the temperature gradient between copper mold and strand in the continuous casting mold. Glassy phase was formed quickly near the cold side when it was quenched from 1500 to 800 °C. Crystals started to precipitate in the glassy region after 48 s. Then major part of the glassy region was gradually transformed to crystalline phase and the crystals subsequently grew to the liquid region. A steady three‐layer state was reached after 360 s.
- 9 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 636-643
In‐Situ Study of Crystallization Behavior of a Mold Flux Using Single and Double Hot Thermocouple Technique
In this study, crystallization behavior of an industrial mold flux was investigated using both single hot thermocouple technique (SHTT) and double hot thermocouple technique (DHTT). Continuous cooling transformation (CCT) and time‐temperature transformation (TTT) diagrams were constructed using SHTT. The critical cooling rate in continuous cooling process was determined as 7 °C s−1 above which a glassy phase was formed. The TTT diagram showed two noses at approximately 1000 and 1075 °C. Phase identification carried out using X‐ray diffraction (XRD) revealed that dicalcium silicate (Ca2SiO4) was the major phase at both 950 and 1100 °C, together with minor precipitates of Na2CaSi3O8 and Ca2MgSi2O7 whose concentrations were relatively higher at 950 °C. Cuspidine (Ca4Si2O7F2) was also identified by XRD at 950 °C. Crystallization kinetics was analyzed using Johnson–Mehl–Avrami–Kolmogorov equation. DHTT was used to simulate the temperature gradient between copper mold and strand in the continuous casting mold. Glassy phase was formed quickly near the cold side when it was quenched from 1500 to 800 °C. Crystals started to precipitate in the glassy region after 48 s. Then major part of the glassy region was gradually transformed to crystalline phase and the crystals subsequently grew to the liquid region. A steady three‐layer state was reached after 360 s.
- 5 January 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 670-677
Melting Properties and Viscosity of SiO2‐CaO‐Al2O3‐B2O3 System
This paper investigated melting properties and viscosity of SiO2‐CaO‐Al2O3‐B2O3 fluxes with a mass ratio of CaO/SiO2 from 0.83 to 1.5 and B2O3 content from 5 to 9 wt%. Melting properties of these fluxes were studied using the hot stage microscopy method; viscosity was measured using the rotating cylinder method. Break temperature was also determined from the viscosity change with temperature in flux cooling process. Equilibrium liquidus temperature was calculated using FactSage. Increase in CaO/SiO2 ratio was found to decrease hemispherical temperature and viscosity. The addition of B2O3 did not significantly affect hemispherical temperature but decreased the flux viscosity. Viscosity was analyzed in relation to the flux structure. The increase of the CaO/SiO2 ratio reduced the degree of flux polymerization, and B2O3 apparently acted as a weak network modifier under the low concentration of B2O3. The experimental viscosity was in a good agreement with calculated viscosity using the modified NPL model.
- 5 January 2015
- Published by Wiley in Steel Research International
- Vol. 86 (6) , 670-677
Melting Properties and Viscosity of SiO2‐CaO‐Al2O3‐B2O3 System
This paper investigated melting properties and viscosity of SiO2‐CaO‐Al2O3‐B2O3 fluxes with a mass ratio of CaO/SiO2 from 0.83 to 1.5 and B2O3 content from 5 to 9 wt%. Melting properties of these fluxes were studied using the hot stage microscopy method; viscosity was measured using the rotating cylinder method. Break temperature was also determined from the viscosity change with temperature in flux cooling process. Equilibrium liquidus temperature was calculated using FactSage. Increase in CaO/SiO2 ratio was found to decrease hemispherical temperature and viscosity. The addition of B2O3 did not significantly affect hemispherical temperature but decreased the flux viscosity. Viscosity was analyzed in relation to the flux structure. The increase of the CaO/SiO2 ratio reduced the degree of flux polymerization, and B2O3 apparently acted as a weak network modifier under the low concentration of B2O3. The experimental viscosity was in a good agreement with calculated viscosity using the modified NPL model.