Paweł Wojewoda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Paweł Wojewoda has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Artur Jaworski
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Str., 35-959 Rzeszow, Poland
3 shared publications - Krzysztof Balawender
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Str., 35-959 Rzeszow, Poland
3 shared publications - Adam Ustrzycki
Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, 35-959 Rzeszów, Poland
2 shared publications Hubert Kuszewski
Rzeszów University of Technology
2 shared publications- Hubert Kuszewski
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Str., 35-959 Rzeszow, Poland
2 shared publications Kazimierz Lejda
Rzeszów University of Technology
2 shared publications
Latest Publications
- Open Access
- 3 October 2025
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 204 (1) , 58-65
The analysis of the impact of the storage period of engine and transmission oil on operational properties
The purpose of the research presented in this article was to determine the impact of the storage period of engine and transmission oils on their operational properties. The prolonged storage of oils leads to a series of physicochemical changes that can significantly affect their lubrication efficiency. Changes such as reduced viscosity, changes in density, and deterioration in lubricity can lead to increased wear of the engine, transmission, and other mechanical components. The study included samples of new and five-year-old engine and transmission oils, as well as engine oil after the break-in period (with a mileage of approximately 800 km). The SAE 10W40 oil after use in an internal combustion engine shows a significant reduction in scuffing resistance (approximately one-third lower scuffing load compared to new and old oil). Long-term five-year storage also slightly reduces its scuffing resistance at higher temperatures. In contrast, long-term storage of SAE 30 oil significantly decreases its scuffing resistance across both tested temperature ranges (by about 20%). Storage time did not significantly alter the viscosity index of SAE 10W40, whereas old SAE 30 oil showed a slightly better index than new oil.
- 3 October 2025
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 204 (1) , 58-65
Open AccessThe analysis of the impact of the storage period of engine and transmission oil on operational properties
The purpose of the research presented in this article was to determine the impact of the storage period of engine and transmission oils on their operational properties. The prolonged storage of oils leads to a series of physicochemical changes that can significantly affect their lubrication efficiency. Changes such as reduced viscosity, changes in density, and deterioration in lubricity can lead to increased wear of the engine, transmission, and other mechanical components. The study included samples of new and five-year-old engine and transmission oils, as well as engine oil after the break-in period (with a mileage of approximately 800 km). The SAE 10W40 oil after use in an internal combustion engine shows a significant reduction in scuffing resistance (approximately one-third lower scuffing load compared to new and old oil). Long-term five-year storage also slightly reduces its scuffing resistance at higher temperatures. In contrast, long-term storage of SAE 30 oil significantly decreases its scuffing resistance across both tested temperature ranges (by about 20%). Storage time did not significantly alter the viscosity index of SAE 10W40, whereas old SAE 30 oil showed a slightly better index than new oil.
- Open Access
Assessment of the Effect of Road Load on Energy Consumption and Exhaust Emissions of a Hybrid Vehicle in an Urban Road Driving Cycle—Comparison of Road and Chassis Dynamometer Tests
Differences between the results obtained in laboratory and road tests of vehicles depend on a number of factors. Among the most important of these are driving cycle and road load. These parameters also affect the hybrid drive control, including the combustion engine operation or driving in electric mode. In most studies, tests carried out on chassis dynamometers concern type approval cycles (NEDC—New European Driving Cycle, WLTC—World-wide harmonized Light duty Test Cycle, FTP— Federal Test Procedure), which differ from real on-road tests. Consequently, the different driving cycles do not allow for results similar to those obtained during on-road driving, especially as the actual cycles on the road are unrepeatable. It is also important to determine the effect of the motion resistance function adopted for chassis dynamometer tests on exhaust emissions and fuel consumption. For this purpose, the authors tested a hybrid car under road and laboratory conditions for the same driving cycle. The analysis was conducted for an example urban road cycle in Rzeszow (URRC). The purpose of the study was to determine the differences in the results of gaseous emissions (THC, CO, CO2, NOx) and fuel consumption (energy) of a hybrid car under road conditions, with the results of tests conducted on a chassis dynamometer, for the same cycle and three functions of resistance.
Open AccessAssessment of the Effect of Road Load on Energy Consumption and Exhaust Emissions of a Hybrid Vehicle in an Urban Road Driving Cycle—Comparison of Road and Chassis Dynamometer Tests
Differences between the results obtained in laboratory and road tests of vehicles depend on a number of factors. Among the most important of these are driving cycle and road load. These parameters also affect the hybrid drive control, including the combustion engine operation or driving in electric mode. In most studies, tests carried out on chassis dynamometers concern type approval cycles (NEDC—New European Driving Cycle, WLTC—World-wide harmonized Light duty Test Cycle, FTP— Federal Test Procedure), which differ from real on-road tests. Consequently, the different driving cycles do not allow for results similar to those obtained during on-road driving, especially as the actual cycles on the road are unrepeatable. It is also important to determine the effect of the motion resistance function adopted for chassis dynamometer tests on exhaust emissions and fuel consumption. For this purpose, the authors tested a hybrid car under road and laboratory conditions for the same driving cycle. The analysis was conducted for an example urban road cycle in Rzeszow (URRC). The purpose of the study was to determine the differences in the results of gaseous emissions (THC, CO, CO2, NOx) and fuel consumption (energy) of a hybrid car under road conditions, with the results of tests conducted on a chassis dynamometer, for the same cycle and three functions of resistance.
- Open Access
Evaluation of the Effect of Chassis Dynamometer Load Setting on CO2 Emissions and Energy Demand of a Full Hybrid Vehicle
Among the solutions that make it possible to reduce CO2 emissions in the transport sector, particularly in urban traffic conditions, are hybrid vehicles. The share of driving performed in electric mode for hybrid vehicles is highly dependent on motion resistance. There are different methods for determining the motion resistance function during chassis dynamometer testing, leading to different test results. Therefore, the main objective of this study was to determine the effect of the chassis dynamometer load function on the energy demand and CO2 emissions of a full-hybrid passenger car. Emissions tests according to the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer for three different methods of determining the car’s resistance to motion. The study showed that adopting the motion resistance function according to different methods, results in differences in CO2 emissions up to about 35% for the entire cycle. Therefore, the authors suggest that in the case of tests carried out with chassis dynamometers, it is necessary to also provide information on the chassis dynamometer loading function adopted for the tests.
Open AccessEvaluation of the Effect of Chassis Dynamometer Load Setting on CO2 Emissions and Energy Demand of a Full Hybrid Vehicle
Among the solutions that make it possible to reduce CO2 emissions in the transport sector, particularly in urban traffic conditions, are hybrid vehicles. The share of driving performed in electric mode for hybrid vehicles is highly dependent on motion resistance. There are different methods for determining the motion resistance function during chassis dynamometer testing, leading to different test results. Therefore, the main objective of this study was to determine the effect of the chassis dynamometer load function on the energy demand and CO2 emissions of a full-hybrid passenger car. Emissions tests according to the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer for three different methods of determining the car’s resistance to motion. The study showed that adopting the motion resistance function according to different methods, results in differences in CO2 emissions up to about 35% for the entire cycle. Therefore, the authors suggest that in the case of tests carried out with chassis dynamometers, it is necessary to also provide information on the chassis dynamometer loading function adopted for the tests.
- 15 September 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Analysis of Cold Start Emission from Light Duty Vehicles Fueled with Gasoline and LPG for Selected Ambient Temperatures
The exhaust emission from modern vehicles is reduced by catalysts except for cold start phase. The difference in emissions for unheated catalysts is large and can reach several times higher than the emission for the heated thermal state of the engine. In the dyno tests, the analysis of the duration and volume of the emissions for harmful exhaust components: CO2 (carbon dioxide), CO (carbon monoxide), THC (total hydrocarbons), NOx (nitrogen oxides) at various climatic chamber operating temperatures, i.e. 0-30oC, for a vehicle meeting the EURO3 and EURO6 standards was performed. Stationary analyzers AVL AMA i60 were used to measure the emissions. The article presents the differences in the emissions for the cold-start phase of engine operation and the duration of time passing to a heated engine for vehicles powered by petrol and LPG (liquefied petroleum gas). The work shows the analysis of modal emissions as well as bag emission.
- 15 September 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Analysis of Cold Start Emission from Light Duty Vehicles Fueled with Gasoline and LPG for Selected Ambient Temperatures
The exhaust emission from modern vehicles is reduced by catalysts except for cold start phase. The difference in emissions for unheated catalysts is large and can reach several times higher than the emission for the heated thermal state of the engine. In the dyno tests, the analysis of the duration and volume of the emissions for harmful exhaust components: CO2 (carbon dioxide), CO (carbon monoxide), THC (total hydrocarbons), NOx (nitrogen oxides) at various climatic chamber operating temperatures, i.e. 0-30oC, for a vehicle meeting the EURO3 and EURO6 standards was performed. Stationary analyzers AVL AMA i60 were used to measure the emissions. The article presents the differences in the emissions for the cold-start phase of engine operation and the duration of time passing to a heated engine for vehicles powered by petrol and LPG (liquefied petroleum gas). The work shows the analysis of modal emissions as well as bag emission.
- Open Access
- 11 October 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 421 (4) , 042002
Analysis of the impact of using additional injectors in the intake manifold on utility and ecological parameters enforced ignition engine
The article presents the results of comparative research on the utility and ecological parameters of the FSO 1.6 GSi engine, which are the effect of using additional injectors in the intake manifold. In the future, these injectors will be responsible for supplying the engine with alternative fuels. Engine parameters such as: cylinder filling factor, torque, unit fuel consumption and exhaust composition were analyzed. The tests were carried out with both standard and modified collector, in which additional injectors were installed.
- 11 October 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 421 (4) , 042002
Open AccessAnalysis of the impact of using additional injectors in the intake manifold on utility and ecological parameters enforced ignition engine
The article presents the results of comparative research on the utility and ecological parameters of the FSO 1.6 GSi engine, which are the effect of using additional injectors in the intake manifold. In the future, these injectors will be responsible for supplying the engine with alternative fuels. Engine parameters such as: cylinder filling factor, torque, unit fuel consumption and exhaust composition were analyzed. The tests were carried out with both standard and modified collector, in which additional injectors were installed.
- Open Access
- 1 November 2017
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 171 (4) , 274-278
The effect of physicochemical properties of fuels on ecological parameters of a diesel engine
The objective of the research results of which are presented in this paper was to determine the effect of selected physicochemical properties of fuels on ecological parameters of a diesl engine. Physicochemical parameters of fuel have a decisive effect on correct functioning, operating parameters, and cleanliness of the exhaust gas emitted to the environment by any combustion engine. Results of physicochemical studies can be useful in developing fuels blends of specific properties, whereas results obtained in the course of tests carried out on an engine test bench allow to optimize parameters of the fuel injection process with the aim to reduce emissions of toxic compounds to atmosphere.
- 1 November 2017
- Published by Polish Scientific Society of Combustion Engines in Combustion Engines
- Vol. 171 (4) , 274-278
Open AccessThe effect of physicochemical properties of fuels on ecological parameters of a diesel engine
The objective of the research results of which are presented in this paper was to determine the effect of selected physicochemical properties of fuels on ecological parameters of a diesl engine. Physicochemical parameters of fuel have a decisive effect on correct functioning, operating parameters, and cleanliness of the exhaust gas emitted to the environment by any combustion engine. Results of physicochemical studies can be useful in developing fuels blends of specific properties, whereas results obtained in the course of tests carried out on an engine test bench allow to optimize parameters of the fuel injection process with the aim to reduce emissions of toxic compounds to atmosphere.