VLVitalii Lyalyuk

Vitalii Lyalyuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Vitalii Lyalyuk has a total of 93 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Improving the technology production of coke for blast furnace smelting

    by Vitaliy Lyalyuk, Kateryna Shmeltser, Daria Kassim

    The most important means of improving blast-furnace performance is to supply high-quality batch – in particular, high-quality coke. Under the conditions of the formed multi-basin raw material base of coking, which predetermines the differences in the technological properties and material composition of imported and domestic coal concentrates, it is necessary to clarify and improve the basic technological methods of preparation for their use in coal mixtures. Achieving optimal characteristics of coke for blast furnace smelting conditions is possible with a comprehensive, scientifically based approach to improving the technology of preparing coal for coking, which consists in developing methods and technological measures aimed at optimizing the composition, properties and degree of grinding of the batch, taking into account its petrographic characteristics.


  • Diameter Selection of Blast Furnace Tuyeres Based on the Rate and Energy of the Fuel-Enriched Blast and Tuyere Gas Flows with the Injection of the Pulverized Coal

    by V. P. Lyalyuk

    The diameter of the air tuyeres on the blast furnace must be selected not based on the change in the kinetic energy of the fuel-enriched blast flow, but in


  • Open Access

    Aerodynamic separation of iron ore pellets by size

    by E.V. Chuprinov, V.P. Lyalyuk, F.M. Zhuravlev, S.V. Shved, I.A. Vasylenko, І.а. Василенко

    The studies on reheating of fired pellets of a suitable fraction used in the bottom and side beds have been analyzed. It has been shown that due to the loss of the crystallization of the glass iron silicate bond, the strength of the pellets decreases at their reduction and their destruction in the metallurgical unit increases, thus leading to a deterioration in its performance. It has been concluded that for the bed, it is necessary to purposefully separate the fraction of the pellets of the required size that does not fall into the finished product. The ways of organizing air classification of fired pellets in open warehouses of finished products have been studied and the possibility of its organization has been considered. The particle trajectories and the factors influencing this process have been analyzed. It has been shown that an important characteristic of the particles dispersion is the influence of the ratio of the coefficient of viscous resistance to the flight of a particle in the air to the mass of a particle, as a result of which an initially flat flow for the particles of different sizes will disintegrate into a fan. This fan of the particles scattering at a certain height can be used to sort them by size class. The conditions have been determined under which the dispersion of the fan of the particles in the horizontal plane will be maximum. Equations have been proposed to describe the law of motion of particles before hitting the jet and after having been blown off by the jet. Mechanisms have been developed for selecting design conditions under which the horizontal distances between the particles of different sizes (the difference of the corresponding coordinates) at the set horizon will be maximum and sufficient for sorting the particles by their size. The visualization of the process of the particle scattering in the MathCAD software environment has been performed, which makes it possible for the technologist to set the initial conditions he needs and to obtain clearly presented final results of the motion of a fan of the particles of different sizes that are clear to him

  • Open Access

    Evaluation of metallurgical value of manganese raw materials

    by V.V. Krivenko, V.P. Lyalyuk, E.V. Chuprinov, I.M. Trus, A.M. Ovcharuk

    Samples of manganese ores of various chemical and fractional compositions, which are widely used nowadays in the production of manganese ferroalloys at domestic enterprises have been investigated. These include samples of manganese ores from the deposits in Georgia, Brazil, Australia and Ghana. Comprehensive studies of the physical and chemical properties and metallurgical value of manganese raw materials from various deposits, used in the production of ferroalloys in ore-reducing furnaces of uprated power, have been carried out. Return to production of concentrate products of raw materials and wastes of ferroalloy production, the use of which in metallurgical processing without preparation and agglomeration is impossible, have been considered. The results of comparative analytical studies of domestic and foreign manganese ore raw materials are presented. The requirements for quality indicators of manganese ores and concentrates according to the regulatory documents of different countries have been compared. Metallurgical properties and kinetic regularities of recovery of the samples of manganese raw materials from various deposits have been investigated. The optimal share of the use of imported raw materials in the charge mixture for the production of manganese ferroalloys in relation to the required phosphorus content in them has been estimated. In accordance with the standard methods in generator gas atmosphere, studies have been carried out to determine the reducibility and temperature of the onset of manganese ores softening. The recoverability has been determined by the weight loss of the sample by the gravimetric method and controlled by chemical analysis

  • Fluxed Local Sinters—Agglomerated Iron Ore Mono Raw Material for Blast-Furnace Smelting

    by F. M. Zhuravlev, V. P. Lyaluk, E. V. Chuprinov, D. A. Kassim, I. A. Lyakhova

    Technologies have been developed and tested for obtaining new types of agglomerated iron ore materials and mono raw materials for blast-furnace smelting, w


  • Oxygen Enrichment and Change of Full Mechanical Energies of Blasting and Hearth Gas

    by V. P. Lyalyuk

    Fulfillment of the application sequence of smelting aids (increase in the blast rate, an increase in top gas pressure, and oxygen enrichment) is one of ess

  • Parametric Analysis of Frictional Self-Oscillations during the Interaction of a Deforming Tool with the Billet

    by Yu. A. Malinovskii, A. D. Uchitel’, V. P. Lyalyuk, G. V. Danilina, D. P. Vlasenkov

    The influence of pulsating dynamic loads at nonstationary self- and parametric oscillations in surface layers of the parts under plastic deformation regard


  • Open Access

    Fluxed local cakes - lumped mono-raw materials for modern blast furnace

    by E.V. Chuprinov, F.M. Zhuravlev, V.P. Lyalyuk, D.O. Kassim, K.O. Shmeltser

    The technology of obtaining fluxed local cakes from iron ore concentrates of different degree of separation has been developed and tested. It has been shown that from one concentrate with different content of SiO2 (1-10%) it is possible to produce fluxed local cakes consisting of a mixture of different basic raw pellets: low-basic – high-temperature and high-basic – low-temperature. Taking into account the positive effect of increasing the iron content in iron ore raw materials on the productivity of the blast furnace and the specific consumption of coke, a method for the production of fluxed local cakes with higher iron content than it is in the sinter and pellets, has been developed. The method is used for the production of fluxed local cakess with a high content of residual carbon due to the use of less scarce and cheap varieties of solid fuels instead of expensive and scarce metallurgical coke. Technological possibilities, indicators of production and metallurgical characteristics of fluxed local cakes have been analyzed. It has been shown that it is technologically possible to obtain a complex fluxed lumpy material with all these metallurgical characteristics, that is local cakes with high iron content and residual carbon. The technology for obtaining such material, which rationally and simultaneously used the above elements of technologies with some technological simplifications has been developed and tested. At the last stage the technology of obtaining mono-raw materials in the form of fluxed local cakes with rolling of a certain thickness shell from high-temperature charge on pieces of anthracite and metallized pellets to prevent their oxidation, which significantly reduces the oxidation of carbon in solid fuels and metallization, was developed


  • Open Access

    Control of the converter melting technological process through the calculated temperature of the reaction zone

    by N.G. Rad’kO, E.V. Chuprinov, V.P. Lyalyuk, M.G. Korenko, V.V. Krivenko

    The article presents calculations of the current temperature of the metal reaction zone and determines its dependence on time at blowing. It has been shown that changes in the temperature of the reaction zone temperature at melting characterize the processes occurring in the bath of the converter. Analysis of the obtained dependence in real time makes it possible to quickly predict the end of oxidation [Si] and [Mn] and the content of [C] in the melt. Besides, the thermal energy of radiation makes it possible in different periods of melting to forecast and to adjust the amount flow of oxygen injected at melting, the necessity to adjust the position of the oxygen lance relative to the metal, and, what is the most important, to predict the completion of blowing. The automation systems implementing the developed model have been offered. It has been shown that it includes sensors of temperature, water and oxygen flow rate and pressure, lance position, means of communication with ACS TP converter melting, control and workstation control, as well as a set of algorithms and programs. An algorithm for calculating the current temperature of the reaction zone during melting has been developed, the algorithm taking the melt as an energy emitter. It has been established that the temperature of the reaction zone reflects through its change in different periods of melting the technological processes in the converter: the temperature of the steel melt, the intensity of the Fe oxidation in the reaction zone, [Si] and [Mn] oxidation processes, endothermic processes strengthening due to Fe oxides in slag, etc. The presented calculations and proposed possibilities of influencing the gas-blowing mode to reduce the supply of oxygen to the melt make it possible for the technologists to achieve the required reduction of steel oxidation and to reduce the deoxidizer costs when casting steel or to predict the substitution of oxygen for air without impairing bath mixing


  • Open Access

    The material composition and characteristics of bentonite clays for use as a binder in the production of iron ore pellets

    by E. V. Chuprinov, F. M. Zhuravlev, V. P. Lyalyuk, D. О. Kassim, І. А. Vasylenko

    Проаналізовано мінералогічний і хімічний склади, а також величину і склад обмінного комплексу різних бентонітових глин. Представлений аналіз показників міцності окатишів з використанням бентонітів із лужним і лужноземельним обмінним комплексом. Показано, що незважаючи на низьке набухання лужноземельних бентонітів, якість окатишів з цими бентонітами в деяких випадках незначно, а в певних умовах і не поступається якістю окатишам із лужними бентонітами при однаковій витраті сполучного