Wolfgang Bronner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wolfgang Bronner has a total of 408 co-authors. Here are the top co-authors by number of shared publications:
M. Schlechtweg
Fraunhofer Institute Applied Solid-State Physics, Tullastr. 72, D-79108 Freiburg, Germany
36 shared publicationsB. Raynor
Fraunhofer Institute for Applied Solid State Physics, Tullastraße 72, 79108 Freiburg, Germany
28 shared publicationsJ. Wagner
Fraunhofer Institute for Applied Solid States Physics (Germany)
27 shared publicationsK. Kohler
Fraunhofer-Inst. fur Angewandte Festkorperphys., Freiburg
26 shared publicationsF. Fuchs
Fraunhofer-Institut für Angewandte Festkörperphysik (Germany)
24 shared publicationsR. Aidam
Fraunhofer Institute for Applied Solid States Physics (Germany)
24 shared publications
Latest Publications
- 1 December 2019
- Published by Frontiers Media SA in Advanced Optical Technologies
- Vol. 8 (6) , 445-450
InGaAs APD matrix sensors for SWIR gated viewing
Short-wavelength infrared (SWIR) detection systems are increasingly in demand for surveillance, reconnaissance, and remote sensing applications. Eye-safe SWIR lasers can be utilized for active imaging systems with high image contrast and long detection range. The gated-viewing (GV) technique using short-pulse lasers and fast-gated cameras in the nanosecond range enables utilizing the distance information in addition to the signal intensity of the acquired images. The InGaAs material system is very well suited for the fabrication of high-performance SWIR photodetectors providing a typical cutoff wavelength of 1.7 mu m, which covers the emission lines of available laser sources at typical telecom wavelengths around 1.55 mu m. However, the usually short integration times needed for GV leads to very small photosignals. We report on the development of SWIR avalanche photodetector (APD) arrays with 640 x 512 pixels and 15 mu m pixel pitch based on the InGaAs material system. The InGaAs-APD focal plane arrays have been successfully integrated into SWIR cameras which yield gain values of M approximate to 10 on camera level at a reverse bias voltage around 21 V and are the first InGaAs-based SWIR cameras worldwide providing a 640 x 512 image format and utilizing avalanche gain for signal amplification. The camera performance is demonstrated by SWIR laser GV sample images.
- 1 December 2019
- Published by Frontiers Media SA in Advanced Optical Technologies
- Vol. 8 (6) , 445-450
InGaAs APD matrix sensors for SWIR gated viewing
Short-wavelength infrared (SWIR) detection systems are increasingly in demand for surveillance, reconnaissance, and remote sensing applications. Eye-safe SWIR lasers can be utilized for active imaging systems with high image contrast and long detection range. The gated-viewing (GV) technique using short-pulse lasers and fast-gated cameras in the nanosecond range enables utilizing the distance information in addition to the signal intensity of the acquired images. The InGaAs material system is very well suited for the fabrication of high-performance SWIR photodetectors providing a typical cutoff wavelength of 1.7 mu m, which covers the emission lines of available laser sources at typical telecom wavelengths around 1.55 mu m. However, the usually short integration times needed for GV leads to very small photosignals. We report on the development of SWIR avalanche photodetector (APD) arrays with 640 x 512 pixels and 15 mu m pixel pitch based on the InGaAs material system. The InGaAs-APD focal plane arrays have been successfully integrated into SWIR cameras which yield gain values of M approximate to 10 on camera level at a reverse bias voltage around 21 V and are the first InGaAs-based SWIR cameras worldwide providing a 640 x 512 image format and utilizing avalanche gain for signal amplification. The camera performance is demonstrated by SWIR laser GV sample images.
- 7 May 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11002, 37
InGaAs SWIR photodetectors for night vision
Short-wave infrared (SWIR) detection systems are increasingly demanded for surveillance, reconnaissance, and remote sensing applications. Passive SWIR cameras can benefit from an extended spectral range, compared to standard nightvision goggles, and the exploitation of the faint night-glow emission from the night sky. Furthermore, eye-safe SWIR lasers can improve the contrast and range of night-vision systems. High-performance SWIR photodetectors can be realized in the InGaAs material system, providing a typical cutoff wavelength of 1.7 μm, which covers a wide part of the night-glow spectrum as well the emission lines of available laser sources at typical telecom wavelengths around 1.55 μm. However, the low photon flux in night-vision applications demand for high responsivities and very low dark-current characteristics of the InGaAs photodetectors. We report on the current development activities of InGaAs SWIR photodetectors at Fraunhofer IAF. We have implemented a planar process technology of InGaAs/InP pin photodiodes for the fabrication of low-light-level SWIR cameras with 640× 512 pixels with 15 μm pixel pitch. Electro-optical characterization results of early-stage process runs exhibit darkcurrent densities below 10-7 A/cm2 at room temperature for 15-μm pitch detector elements. The current activities focus on further reducing the dark current to reach the international state of the art. Moreover, InGaAs-based avalanche photodiode (APD) have been developed for active SWIR imaging. Gain values of M ≈ 10 on camera level at a reverse bias voltage around 20 V have been achieved by a sophisticated vertical detector design. FPAs of such InGaAs-APD material have been successfully integrated into SWIR cameras with 640 × 512 pixels at 15 μm pixel pitch and operated in SWIR laser gated viewing mode.
- 7 May 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11002, 37
InGaAs SWIR photodetectors for night vision
Short-wave infrared (SWIR) detection systems are increasingly demanded for surveillance, reconnaissance, and remote sensing applications. Passive SWIR cameras can benefit from an extended spectral range, compared to standard nightvision goggles, and the exploitation of the faint night-glow emission from the night sky. Furthermore, eye-safe SWIR lasers can improve the contrast and range of night-vision systems. High-performance SWIR photodetectors can be realized in the InGaAs material system, providing a typical cutoff wavelength of 1.7 μm, which covers a wide part of the night-glow spectrum as well the emission lines of available laser sources at typical telecom wavelengths around 1.55 μm. However, the low photon flux in night-vision applications demand for high responsivities and very low dark-current characteristics of the InGaAs photodetectors. We report on the current development activities of InGaAs SWIR photodetectors at Fraunhofer IAF. We have implemented a planar process technology of InGaAs/InP pin photodiodes for the fabrication of low-light-level SWIR cameras with 640× 512 pixels with 15 μm pixel pitch. Electro-optical characterization results of early-stage process runs exhibit darkcurrent densities below 10-7 A/cm2 at room temperature for 15-μm pitch detector elements. The current activities focus on further reducing the dark current to reach the international state of the art. Moreover, InGaAs-based avalanche photodiode (APD) have been developed for active SWIR imaging. Gain values of M ≈ 10 on camera level at a reverse bias voltage around 20 V have been achieved by a sophisticated vertical detector design. FPAs of such InGaAs-APD material have been successfully integrated into SWIR cameras with 640 × 512 pixels at 15 μm pixel pitch and operated in SWIR laser gated viewing mode.
- 9 October 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10795, 1079503
InGaAs-based SWIR photodetectors for night vision and gated viewing
High-performance short-wavelength infrared (SWIR) photodetectors can be realized in the InGaAs material system, providing a typical cutoff wavelength of 1.7 μm, which covers a wide part of the nightglow spectrum as well as the emission lines of available laser sources at typical telecom wavelengths around 1.55 μm. However, both, active and passive SWIR detection systems are mostly required to provide high responsivities and very low dark currents in order to detect extremely low photon fluxes. This can be achieved with pin photodiodes with high responsivities and very low dark current characteristics or by utilizing the internal signal gain as provided by avalanche photodiodes (APDs). We develop SWIR photodetectors based on InGaAs/InP pin diodes and InGaAs/InAlAs/InP APDs as single-element detectors as well as focal plane arrays (FPAs). The planar processed InGaAs/InP pin photodiodes for low-light-level SWIR cameras exhibit dark current densities of 10-7 A/cm2 at room temperature for 15 μm pitch detector elements. For the APDs, emphasis is put on the vertical detector design. Within three design iterations, the operating voltage for useful gain values M ~ 10 could be reduced from 27 V down to 18 V, which was crucial for the operation with the voltage limitation of the read-out circuit. FPAs of such InGaAs-APD material have been successfully integrated into SWIR cameras with 640 × 512 pixels at 15 μm pixel pitch. The avalanche operation on camera level has been demonstrated for both kinds, the standard (passive) as well as gated-viewing operation modes.
- 9 October 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10795, 1079503
InGaAs-based SWIR photodetectors for night vision and gated viewing
High-performance short-wavelength infrared (SWIR) photodetectors can be realized in the InGaAs material system, providing a typical cutoff wavelength of 1.7 μm, which covers a wide part of the nightglow spectrum as well as the emission lines of available laser sources at typical telecom wavelengths around 1.55 μm. However, both, active and passive SWIR detection systems are mostly required to provide high responsivities and very low dark currents in order to detect extremely low photon fluxes. This can be achieved with pin photodiodes with high responsivities and very low dark current characteristics or by utilizing the internal signal gain as provided by avalanche photodiodes (APDs). We develop SWIR photodetectors based on InGaAs/InP pin diodes and InGaAs/InAlAs/InP APDs as single-element detectors as well as focal plane arrays (FPAs). The planar processed InGaAs/InP pin photodiodes for low-light-level SWIR cameras exhibit dark current densities of 10-7 A/cm2 at room temperature for 15 μm pitch detector elements. For the APDs, emphasis is put on the vertical detector design. Within three design iterations, the operating voltage for useful gain values M ~ 10 could be reduced from 27 V down to 18 V, which was crucial for the operation with the voltage limitation of the read-out circuit. FPAs of such InGaAs-APD material have been successfully integrated into SWIR cameras with 640 × 512 pixels at 15 μm pixel pitch. The avalanche operation on camera level has been demonstrated for both kinds, the standard (passive) as well as gated-viewing operation modes.
- 22 February 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10087, 1008705
GaSb-based VECSEL for high-power applications and Ho-pumping
The (AlGaIn)(AsSb) material system has been shown to be ideally suited to realize VECSELs for the 2-3 μm wavelength range. In this report we will present results on increasing the output power of the SDL chips with special emphasis on the 2.8 μm emission wavelength by means of low quantum defect pumping. Further on we have investigated concepts for a VECSEL-pumped Q-switched Ho:YAG laser in order to convert the high cw-power of the VECSEL into pulses with a high peak power. Up to 3.3 mJ of pulse energy were achieved with a compact setup (corresponding to a peak power of 30 kW at 110 ns pulse length) combined with stable pulsing behavior.
- 22 February 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10087, 1008705
GaSb-based VECSEL for high-power applications and Ho-pumping
The (AlGaIn)(AsSb) material system has been shown to be ideally suited to realize VECSELs for the 2-3 μm wavelength range. In this report we will present results on increasing the output power of the SDL chips with special emphasis on the 2.8 μm emission wavelength by means of low quantum defect pumping. Further on we have investigated concepts for a VECSEL-pumped Q-switched Ho:YAG laser in order to convert the high cw-power of the VECSEL into pulses with a high peak power. Up to 3.3 mJ of pulse energy were achieved with a compact setup (corresponding to a peak power of 30 kW at 110 ns pulse length) combined with stable pulsing behavior.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 233-236
Internally-packaged-matched continuous inverse class-FI wideband GaN HPA
This paper shows a wideband high power efficiency amplifier with internal package matching. The power amplifier has been designed and realized by using the Continuous Inverse Class-FI approach for wideband applications. In particular, the fundamental as well as the second and third harmonic output terminations have been matched inside the packaged transistor without the use of further external output matching conditions. The realized prototype shows drain efficiencies in the range of 59.5-71% while delivering 42.4-45.7 dBm of output power in the very wide frequency range of 1.8-2.7 GHz.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 233-236
Internally-packaged-matched continuous inverse class-FI wideband GaN HPA
This paper shows a wideband high power efficiency amplifier with internal package matching. The power amplifier has been designed and realized by using the Continuous Inverse Class-FI approach for wideband applications. In particular, the fundamental as well as the second and third harmonic output terminations have been matched inside the packaged transistor without the use of further external output matching conditions. The realized prototype shows drain efficiencies in the range of 59.5-71% while delivering 42.4-45.7 dBm of output power in the very wide frequency range of 1.8-2.7 GHz.
- 19 September 2016
- Published by SPIE-Intl Soc Optical Eng
- p. 99740G-99740G-11
SWIR detectors for low photon fluxes
Active and passive short-wave infrared (SWIR) detection systems for surveillance and remote sensing applications are mostly required to detect extremely low photon fluxes. This can be achieved by utilizing the internal signal gain as provided by avalanche photodiodes (APDs). We report on our current development activities of SWIR photodetectors based on InGaAs/InAlAs/InP APDs, covering detector design, epitaxial growth, process technology, and electro-optical characterization results of single-element detectors and fanout hybrids. For the first time, the operation of an InGaAs based SWIR camera with 640 × 512 pixels utilizing APDs for signal amplification is demonstrated for operating temperatures of 180 K and even 260 K
- 19 September 2016
- Published by SPIE-Intl Soc Optical Eng
- p. 99740G-99740G-11
SWIR detectors for low photon fluxes
Active and passive short-wave infrared (SWIR) detection systems for surveillance and remote sensing applications are mostly required to detect extremely low photon fluxes. This can be achieved by utilizing the internal signal gain as provided by avalanche photodiodes (APDs). We report on our current development activities of SWIR photodetectors based on InGaAs/InAlAs/InP APDs, covering detector design, epitaxial growth, process technology, and electro-optical characterization results of single-element detectors and fanout hybrids. For the first time, the operation of an InGaAs based SWIR camera with 640 × 512 pixels utilizing APDs for signal amplification is demonstrated for operating temperatures of 180 K and even 260 K
- 25 May 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9836, 98362I
Imaging standoff trace detection of explosives using IR-laser based backscattering
We perform active hyperspectral imaging using tunable mid-infrared (MIR) quantum cascade lasers for contactless identification of solid and liquid contaminations on surfaces. By collecting the backscattered laser radiation with a camera, a hyperspectral data cube, containing the spatially resolved spectral information of the scene is obtained. Data is analyzed using appropriate algorithms to find the target substances even on substrates with a priori unknown spectra. Eye-save standoff detection of residues of explosives and precursors over extended distances is demonstrated and the main purpose of our system. Using a MIR EC-QCL with a tuning range from 7.5 μm to 10 μm, detection of a large variety of explosives, e.g. TNT, PETN and RDX and precursor materials such as Ammonium Nitrate could be demonstrated. In a real world scenario stand-off detection over distances of up to 20 m could be successfully performed. This includes measurements in a post blast scenario demonstrating the potential of the technique for forensic investigations.
- 25 May 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9836, 98362I
Imaging standoff trace detection of explosives using IR-laser based backscattering
We perform active hyperspectral imaging using tunable mid-infrared (MIR) quantum cascade lasers for contactless identification of solid and liquid contaminations on surfaces. By collecting the backscattered laser radiation with a camera, a hyperspectral data cube, containing the spatially resolved spectral information of the scene is obtained. Data is analyzed using appropriate algorithms to find the target substances even on substrates with a priori unknown spectra. Eye-save standoff detection of residues of explosives and precursors over extended distances is demonstrated and the main purpose of our system. Using a MIR EC-QCL with a tuning range from 7.5 μm to 10 μm, detection of a large variety of explosives, e.g. TNT, PETN and RDX and precursor materials such as Ammonium Nitrate could be demonstrated. In a real world scenario stand-off detection over distances of up to 20 m could be successfully performed. This includes measurements in a post blast scenario demonstrating the potential of the technique for forensic investigations.
- 13 February 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9755, 97550A
Quantum cascade laser based active hyperspectral imaging for standoff detection of chemicals on surfaces
We employ active hyperspectral imaging using tunable mid-infrared (MIR) quantum cascade lasers for contactless identification of solid and liquid contaminations on surfaces. By collecting the backscattered laser radiation with a camera, a hyperspectral data cube, containing the spatially resolved spectral information of the scene is obtained. Data is analyzed using appropriate algorithms to find the target substances even on substrates with a priori unknown spectra. Eye-save standoff detection of residues of explosives and precursors over extended distances is demonstrated and the main purpose of our system. However, it can be applied to any substance with characteristic reflectance / absorbance spectrum. As an example, we present first results of monitoring food quality by distinguishing fresh and mold contaminated peanuts by their MIR backscattering spectrum.
- 13 February 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9755, 97550A
Quantum cascade laser based active hyperspectral imaging for standoff detection of chemicals on surfaces
We employ active hyperspectral imaging using tunable mid-infrared (MIR) quantum cascade lasers for contactless identification of solid and liquid contaminations on surfaces. By collecting the backscattered laser radiation with a camera, a hyperspectral data cube, containing the spatially resolved spectral information of the scene is obtained. Data is analyzed using appropriate algorithms to find the target substances even on substrates with a priori unknown spectra. Eye-save standoff detection of residues of explosives and precursors over extended distances is demonstrated and the main purpose of our system. However, it can be applied to any substance with characteristic reflectance / absorbance spectrum. As an example, we present first results of monitoring food quality by distinguishing fresh and mold contaminated peanuts by their MIR backscattering spectrum.
- 9 December 2015
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (4) , 925-929
Charge-layer design considerations in SAGCM InGaAs/InAlAs avalanche photodiodes
- 9 December 2015
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (4) , 925-929
Charge-layer design considerations in SAGCM InGaAs/InAlAs avalanche photodiodes
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (6) , 324-335
Recent Advances in Power Scaling of GaSb-Based Semiconductor Disk Lasers
GaSb-based semiconductor disk lasers (SDLs) cover the application-rich 2-3-μm wavelength range. The output power of these lasers is mainly limited by the active region heating and resulting thermal rollover, caused by the waste heat deposited in SDL chip. We present recent advances achieved in 1) reducing the heat load on the SDL chip by reducing the quantum deficit, and 2) removing the waste heat more efficiently by combining front- and backside heat sinking. The latter step was based on extensive thermal simulations of the heat distribution and heat flow within SDL chip and submount, which are also presented. Combining both approaches, we could demonstrate 20 W of continuous wave output power from a GaSb-based single-chip SDL operating at 2 μm and a heat sink temperature of 0 °C. A comparative analysis of the similarities and differences to GaAs-based SDLs emitting around 1 μm is given.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (6) , 324-335
Recent Advances in Power Scaling of GaSb-Based Semiconductor Disk Lasers
GaSb-based semiconductor disk lasers (SDLs) cover the application-rich 2-3-μm wavelength range. The output power of these lasers is mainly limited by the active region heating and resulting thermal rollover, caused by the waste heat deposited in SDL chip. We present recent advances achieved in 1) reducing the heat load on the SDL chip by reducing the quantum deficit, and 2) removing the waste heat more efficiently by combining front- and backside heat sinking. The latter step was based on extensive thermal simulations of the heat distribution and heat flow within SDL chip and submount, which are also presented. Combining both approaches, we could demonstrate 20 W of continuous wave output power from a GaSb-based single-chip SDL operating at 2 μm and a heat sink temperature of 0 °C. A comparative analysis of the similarities and differences to GaAs-based SDLs emitting around 1 μm is given.