Flávio Luiz de Silva Bussamra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Flávio Luiz de Silva Bussamra has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Eliseu Lucena Neto
Instituto Tecnológico de Aeronáutica, Brazil
4 shared publications - Angelo Antonio Verri
EMBRAER S/A
3 shared publications Carlos E. S. Cesnik
University of Michigan, Ann Arbor, Michigan 48109-2140
2 shared publications- Alessandro Teixeira Neto
Instituto Tecnológico de Aeronáutica, Brazil
1 shared publication - Anaisa de Paula Guedes Villani1 shared publication
- Antônio Bernardo Guimarães Neto
Aeronautics Institute of Technology, 12228-900 São José dos Campos, Brazil
1 shared publication
Latest Publications
- 2 January 2026
- Published by Springer Nature
- p. 51-60
Proposal and Validation of a Coarser Structural Mesh for Static and Dynamic Analyses of the Common Research Model Aircraft
- 2 January 2026
- Published by Springer Nature
- p. 51-60
Proposal and Validation of a Coarser Structural Mesh for Static and Dynamic Analyses of the Common Research Model Aircraft
- 22 July 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1-12
Static aeroelastic rolling of a highly flexible wing: Pazy wing with aileron
- 22 July 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1-12
Static aeroelastic rolling of a highly flexible wing: Pazy wing with aileron
- 1 January 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (1) , 285-304
Flexible Aircraft Simulation Validation with Flight Test Data
The challenges of modeling flexible aircraft include appropriate fidelity capturing and validation with experimental data. In fact, the validation of formulations and models for the flexible flight dynamics is indispensable to ensure that all the important phenomena are correctly captured. With this objective, two high-aspect-ratio flexible aircraft have been flight-tested, and coupled aeroelastic–flight dynamics data have been collected to support model validation. Additional ground vibration and static tests were carried out to fully characterize the structural dynamic properties. Numerical models were built based on a linear structural representation but with geometrically nonlinear aerodynamics. Low Reynolds number effects were included in a simplified way with lookup tables of two-dimensional airfoil data. Wing-tip effects were considered via the vortex- and doublet-lattice methods. Propulsive data were obtained with wind-tunnel tests. This paper describes the numerical models, the two aircraft, and their instrumentation and presents the data collected from the aircraft sensors during flight tests. Numerical and experimental results are compared for angular velocities, accelerations, and strains measured at different points of the aircraft. Despite its limitations and simplifications, the numerical model captures the real aircraft main aeroelastic and flight dynamic behaviors.
- 1 January 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (1) , 285-304
Flexible Aircraft Simulation Validation with Flight Test Data
The challenges of modeling flexible aircraft include appropriate fidelity capturing and validation with experimental data. In fact, the validation of formulations and models for the flexible flight dynamics is indispensable to ensure that all the important phenomena are correctly captured. With this objective, two high-aspect-ratio flexible aircraft have been flight-tested, and coupled aeroelastic–flight dynamics data have been collected to support model validation. Additional ground vibration and static tests were carried out to fully characterize the structural dynamic properties. Numerical models were built based on a linear structural representation but with geometrically nonlinear aerodynamics. Low Reynolds number effects were included in a simplified way with lookup tables of two-dimensional airfoil data. Wing-tip effects were considered via the vortex- and doublet-lattice methods. Propulsive data were obtained with wind-tunnel tests. This paper describes the numerical models, the two aircraft, and their instrumentation and presents the data collected from the aircraft sensors during flight tests. Numerical and experimental results are compared for angular velocities, accelerations, and strains measured at different points of the aircraft. Despite its limitations and simplifications, the numerical model captures the real aircraft main aeroelastic and flight dynamic behaviors.
- 30 November 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (12) , 1-14
Hybrid calibration of aeronautical structures instrumented with strain-gages for load prediction
- 30 November 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (12) , 1-14
Hybrid calibration of aeronautical structures instrumented with strain-gages for load prediction
- RetractedOpen Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 17 (7)
On the sparsity of linear systems of equations for a new stress basis applied to three-dimensional Hybrid-Trefftz stress finite elements
Hybrid-Trefftz finite elements have been applied to the analysis of several types of structures successfully. It is based on two different sets of approximations applied simultaneously: stresses in the domain and displacements on its boundary. This method presents very large linear systems of equations to be solved. To overcome this issue, most authors have been careful in the choice of the approximation fields in order to have highly sparse linear systems. The natural choice for the stress basis has been linearly independent, hierarchical and orthogonal polynomials which typically result in more than 90% of sparsity in 3-D finite elements. Functions derived from associated Legendre and Chebyshev orthogonal polynomials have been used with success for this purpose. In this work the non-orthogonal polynomials available in the Pascal pyramid are proposed to derive a harmonic and complete set of polynomial basis as an alternative to the above-cited functions. Numerical tests show this basis produces accurate results. No significant differences were found when comparing the sparsity of the linear system of equations for both functions.
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 17 (7)
RetractedOpen AccessOn the sparsity of linear systems of equations for a new stress basis applied to three-dimensional Hybrid-Trefftz stress finite elements
Hybrid-Trefftz finite elements have been applied to the analysis of several types of structures successfully. It is based on two different sets of approximations applied simultaneously: stresses in the domain and displacements on its boundary. This method presents very large linear systems of equations to be solved. To overcome this issue, most authors have been careful in the choice of the approximation fields in order to have highly sparse linear systems. The natural choice for the stress basis has been linearly independent, hierarchical and orthogonal polynomials which typically result in more than 90% of sparsity in 3-D finite elements. Functions derived from associated Legendre and Chebyshev orthogonal polynomials have been used with success for this purpose. In this work the non-orthogonal polynomials available in the Pascal pyramid are proposed to derive a harmonic and complete set of polynomial basis as an alternative to the above-cited functions. Numerical tests show this basis produces accurate results. No significant differences were found when comparing the sparsity of the linear system of equations for both functions.
- Open Access
- 23 October 2019
- Published by Linkoping University Electronic Press
- No. 162,p. 263-271
Analysis of the Impact of the Conclusion of the Collaborative Professional Master's Program on Embraer and ITA
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!
- 23 October 2019
- Published by Linkoping University Electronic Press
- No. 162,p. 263-271
Open AccessAnalysis of the Impact of the Conclusion of the Collaborative Professional Master's Program on Embraer and ITA
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!
- 1 February 2018
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 140, 50-58
Three-dimensional hybrid-mixed stress elements for free vibration analysis
- 1 February 2018
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 140, 50-58
Three-dimensional hybrid-mixed stress elements for free vibration analysis
- 6 December 2017
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 113 (11) , 1676-1696
Three dimensional hybrid‐Trefftz stress finite elements for plates and shells
Summary: Three‐dimensional hybrid‐Trefftz stress finite elements for plates and shells are proposed. Two independent fields are approximated: stresses within the element and displacement on their boundary. The required stress field derived from the Papkovitch‐Neuber solution of the Navier equation, which a priori satisfies the Trefftz constraint, is generated using homogeneous harmonic polynomials. Restriction on the polynomial degree in the coordinate measured along the thickness direction is imposed to reduce the number of independent terms. Explicit expressions of the corresponding independent polynomials are listed up to the fifth order. Illustrative applications to evaluate displacements and stresses are conducted by hexahedral hybrid‐Trefftz stress element models. The hierarchical p‐ and h‐refinement strategy are exploited in the numerical tests.
- 6 December 2017
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 113 (11) , 1676-1696
Three dimensional hybrid‐Trefftz stress finite elements for plates and shells
Summary: Three‐dimensional hybrid‐Trefftz stress finite elements for plates and shells are proposed. Two independent fields are approximated: stresses within the element and displacement on their boundary. The required stress field derived from the Papkovitch‐Neuber solution of the Navier equation, which a priori satisfies the Trefftz constraint, is generated using homogeneous harmonic polynomials. Restriction on the polynomial degree in the coordinate measured along the thickness direction is imposed to reduce the number of independent terms. Explicit expressions of the corresponding independent polynomials are listed up to the fifth order. Illustrative applications to evaluate displacements and stresses are conducted by hexahedral hybrid‐Trefftz stress element models. The hierarchical p‐ and h‐refinement strategy are exploited in the numerical tests.
- Open Access
- 1 January 2017
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 14 (13) , 2402-2422
An Enhanced Random Vibration and Fatigue Model for Printed Circuit Boards
Aerospace vehicles are mostly exposed to random vibration loads during its operational lifetime. These harsh conditions excites vibration responses in the vehicles printed circuit boards, what can cause failure on mission functionality due to fatigue damage of electronic components. A novel analytical model to evaluate the useful life of embedded electronic components (capacitors, chips, oscillators etc.) mounted on Printed Circuit Boards (PCB) is presented. The fatigue damage predictions are calculated by the relative displacement between the PCB and the component, the lead stiffness, as well the natural vibration modes of the PCB and the component itself. Statistical methods are used for fatigue cycle counting. The model is applied to experimental fatigue tests of PCBs available on literature. The analytical results are of the same magnitude order of the experimental findings.
- 1 January 2017
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 14 (13) , 2402-2422
Open AccessAn Enhanced Random Vibration and Fatigue Model for Printed Circuit Boards
Aerospace vehicles are mostly exposed to random vibration loads during its operational lifetime. These harsh conditions excites vibration responses in the vehicles printed circuit boards, what can cause failure on mission functionality due to fatigue damage of electronic components. A novel analytical model to evaluate the useful life of embedded electronic components (capacitors, chips, oscillators etc.) mounted on Printed Circuit Boards (PCB) is presented. The fatigue damage predictions are calculated by the relative displacement between the PCB and the component, the lead stiffness, as well the natural vibration modes of the PCB and the component itself. Statistical methods are used for fatigue cycle counting. The model is applied to experimental fatigue tests of PCBs available on literature. The analytical results are of the same magnitude order of the experimental findings.