Oskar Javier González Pedraza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Oskar Javier González Pedraza has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Rubio-Maya
Universidad Michoacana de San Nicolás de Hidalgo, Facultad de Ingeniería Mecánica
3 shared publications - Daniel Alcantar Martinez
Universidad Michoacana de San Nicolás de Hidalgo, Morelia, México
2 shared publications J. Jesús Pacheco Ibarra
2 shared publicationsJorge Alberto Rangel Arista
2 shared publicationsA. N. Conejo
Graduate Program in Metallurgy, Morelia Technological Institute (ITM)
1 shared publication- Carlos Alberto Guizar Gómez1 shared publication
Latest Publications
- Open Access
- 11 March 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 81
Thermal design and experimental validation of a dual-CCT chip-on-board LED module
- 11 March 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 81
Open AccessThermal design and experimental validation of a dual-CCT chip-on-board LED module
- 1 September 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 142, 292-302
Numerical study of the drift and evaporation of water droplets cooled down by a forced stream of air
- 1 September 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 142, 292-302
Numerical study of the drift and evaporation of water droplets cooled down by a forced stream of air
- Open Access
- 1 July 2017
- Published by ASTES Journal in Advances in Science, Technology and Engineering Systems Journal
- Vol. 2 (3) , 1064-1069
Applied Horizontal and Vertical Geothermal Heat Exchanger with Heat Pump System to Provide Air Conditioning for an Academic Facility in Mexico
- 1 July 2017
- Published by ASTES Journal in Advances in Science, Technology and Engineering Systems Journal
- Vol. 2 (3) , 1064-1069
Open AccessApplied Horizontal and Vertical Geothermal Heat Exchanger with Heat Pump System to Provide Air Conditioning for an Academic Facility in Mexico
- 11 November 2016
- Published by ASME International
Numerical Analysis of Geothermal Heat Exchangers to be Implemented in a Geothermal-Solar Hybrid Power Plant for Electricity Production in Mexico
The Mexican government due to the need of developing and creating cutting-edge technology for application of renewable energy has created renewable energy centers to develop research projects related to solar, wind and geothermal energy. In particular, geothermal energy has been of great interest due to high geothermal energy potential reported for the country. Regarding the projects approved by the Mexican government, the Universidad Michoacana de San Nicolás de Hidalgo, has been granted with fundings to carry out the design and implementation of a geothermal-solar hybrid plant for electricity production. This project is being developed in the community of San Nicolás Simirao (Michoacan State) where geothermal energy is available and exploited from an existing geothermal well. Initially, the well ran through induction, but fluid flow was not constant for long periods and was not sufficient to obtain a full operation of the geothermal-solar hybrid power plant. Therefore, it was necessary to explore new techniques to extract geothermal energy effectively, meeting design conditions of power plant. One solution might be a geothermal heat exchanger to extract heat from the rock and carry it to the surface. Literature reports two basic configurations of geothermal heat exchangers: one of them is the Downhole Coaxial Heat Exchanger and the other one is Borehole Heat Exchanger. Before making a decision to implement one type or another, several studies were carried out by the authors of this work to determine what type of configuration was most suitable, considering in such studies technical and economic aspects that provided information to continue or not the project. Therefore, in this paper the numerical analysis of both configurations (Downhole Coaxial Heat Exchanger and Borehole Heat Exchanger) is presented. The study was conducted to determine what type of geothermal exchanger presents the best trade-off between maximum heat extraction rate and minimum length to minimize costs. A minimum temperature of 125°C was proposed to reach at the hot fluid heat exchanger outlet, allowing a normal operation of the geothermal-solar hybrid plant. Through numerical analysis was determined that the Borehole Heat Exchanger configuration did not present good heat extractions rates, obtaining that for 100 m length the outlet temperature of the hot fluid was even lower to that of entering into the well. This behavior was attributed to heat loss in the return pipe. For the same configuration, but using a length of 500 m, a temperature of 117.21°C was reached at the heat exchanger outlet. On the other hand, the Downhole Coaxial Heat Exchanger configuration reached a temperature of 118.35°C for a length of 100 m. For a length of 200 m a temperature of 131.25°C was obtained, whereby the facility can operate with the minimum necessary conditions. Finally, for a length of 500 m, a temperature of 134.67°C was reached, showing that this type of configuration is the most suitable to be installed in the geothermal well. Thus the Downhole Coaxial Heat Exchanger configuration has more advantages than the Borehole Heat Exchanger configuration from a technical and economic (by pipe cost) point of view.
- 11 November 2016
- Published by ASME International
Numerical Analysis of Geothermal Heat Exchangers to be Implemented in a Geothermal-Solar Hybrid Power Plant for Electricity Production in Mexico
The Mexican government due to the need of developing and creating cutting-edge technology for application of renewable energy has created renewable energy centers to develop research projects related to solar, wind and geothermal energy. In particular, geothermal energy has been of great interest due to high geothermal energy potential reported for the country. Regarding the projects approved by the Mexican government, the Universidad Michoacana de San Nicolás de Hidalgo, has been granted with fundings to carry out the design and implementation of a geothermal-solar hybrid plant for electricity production. This project is being developed in the community of San Nicolás Simirao (Michoacan State) where geothermal energy is available and exploited from an existing geothermal well. Initially, the well ran through induction, but fluid flow was not constant for long periods and was not sufficient to obtain a full operation of the geothermal-solar hybrid power plant. Therefore, it was necessary to explore new techniques to extract geothermal energy effectively, meeting design conditions of power plant. One solution might be a geothermal heat exchanger to extract heat from the rock and carry it to the surface. Literature reports two basic configurations of geothermal heat exchangers: one of them is the Downhole Coaxial Heat Exchanger and the other one is Borehole Heat Exchanger. Before making a decision to implement one type or another, several studies were carried out by the authors of this work to determine what type of configuration was most suitable, considering in such studies technical and economic aspects that provided information to continue or not the project. Therefore, in this paper the numerical analysis of both configurations (Downhole Coaxial Heat Exchanger and Borehole Heat Exchanger) is presented. The study was conducted to determine what type of geothermal exchanger presents the best trade-off between maximum heat extraction rate and minimum length to minimize costs. A minimum temperature of 125°C was proposed to reach at the hot fluid heat exchanger outlet, allowing a normal operation of the geothermal-solar hybrid plant. Through numerical analysis was determined that the Borehole Heat Exchanger configuration did not present good heat extractions rates, obtaining that for 100 m length the outlet temperature of the hot fluid was even lower to that of entering into the well. This behavior was attributed to heat loss in the return pipe. For the same configuration, but using a length of 500 m, a temperature of 117.21°C was reached at the heat exchanger outlet. On the other hand, the Downhole Coaxial Heat Exchanger configuration reached a temperature of 118.35°C for a length of 100 m. For a length of 200 m a temperature of 131.25°C was obtained, whereby the facility can operate with the minimum necessary conditions. Finally, for a length of 500 m, a temperature of 134.67°C was reached, showing that this type of configuration is the most suitable to be installed in the geothermal well. Thus the Downhole Coaxial Heat Exchanger configuration has more advantages than the Borehole Heat Exchanger configuration from a technical and economic (by pipe cost) point of view.
- 13 November 2015
- Published by ASME International
Conceptual Design and Numerical Modeling of Prototype Counterflow Cooling Tower With Forced Draft for Geothermal Applications
Cooling towers are widely used in temperature control in industrial processes and electricity generation processes by conventional and renewable energy methods. In this paper, it is presented an integral design of a counterflow cooling tower with forced draft for geothermal applications. The conceptual design was done in SolidWorks® software and the numerical simulation of the fluid through the tower was performed in Fluent® software. In the conceptual design were made both structural and tower elements design of the counterflow tower with forced draft. Besides, it was designed a self-drive sprinkler which distributes the water flow to be cooled inside the tower. In the mathematical model the velocity and temperature profiles were analyzed under different turbulence models that allow to increase their accuracy, as a result of this, it was able to calculate the heat transfer in the boundary layer between the walls packing and circulating air inside the tower. As a consequence could be estimate the coefficient of convective heat transfer.
- 13 November 2015
- Published by ASME International
Conceptual Design and Numerical Modeling of Prototype Counterflow Cooling Tower With Forced Draft for Geothermal Applications
Cooling towers are widely used in temperature control in industrial processes and electricity generation processes by conventional and renewable energy methods. In this paper, it is presented an integral design of a counterflow cooling tower with forced draft for geothermal applications. The conceptual design was done in SolidWorks® software and the numerical simulation of the fluid through the tower was performed in Fluent® software. In the conceptual design were made both structural and tower elements design of the counterflow tower with forced draft. Besides, it was designed a self-drive sprinkler which distributes the water flow to be cooled inside the tower. In the mathematical model the velocity and temperature profiles were analyzed under different turbulence models that allow to increase their accuracy, as a result of this, it was able to calculate the heat transfer in the boundary layer between the walls packing and circulating air inside the tower. As a consequence could be estimate the coefficient of convective heat transfer.
- Open Access
- 1 January 2010
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 50 (1) , 1-8
Effect of Arc Length on Fluid Flow and Mixing Phenomena in AC Electric Arc Furnaces
Fluid flow and mixing phenomena in an industrial three phase Electric Arc Furnace has been investigated, as a function of arc length. Velocity and temperature fields as well as mixing times were computed, assuming that liquid steel occupies the whole computational domain and buoyancy forces are responsible for convective flow. It is reported a strong effect of arc length on both fluid flow and mixing time, suggesting a metallurgical practice with long arc operation to improve the melting kinetics of the metallic charge. Thermal stratification has also been confirmed, however the volume of hot steel increases when arc length also increases.
- 1 January 2010
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 50 (1) , 1-8
Open AccessEffect of Arc Length on Fluid Flow and Mixing Phenomena in AC Electric Arc Furnaces
Fluid flow and mixing phenomena in an industrial three phase Electric Arc Furnace has been investigated, as a function of arc length. Velocity and temperature fields as well as mixing times were computed, assuming that liquid steel occupies the whole computational domain and buoyancy forces are responsible for convective flow. It is reported a strong effect of arc length on both fluid flow and mixing time, suggesting a metallurgical practice with long arc operation to improve the melting kinetics of the metallic charge. Thermal stratification has also been confirmed, however the volume of hot steel increases when arc length also increases.