Leszek Malyszko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Leszek Malyszko has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Andrzej Rutkiewicz
Faculty of Geoengineering, University of Warmia and Mazury in Olsztyn, Prawocheńskiego 15, 10-720 Olsztyn, Poland
4 shared publications - Piotr Bilko
Uniwersytet Warmińsko-Mazurski w Olsztynie
4 shared publications Edyta Kowalska
2 shared publications- Aneta Skoratko
Faculty of Geoengineering University of Warmia and Mazury in Olsztyn Olsztyn Poland
1 shared publication - Edyta Kowalska
Univ Warmia & Mazury, Inst Geodesy & Civil Engn, Fac Geoengn, PL-10720 Olsztyn, Poland
1 shared publication - Jacek Paziewski
University of Warmia and Mazury in Olsztyn, Olsztyn, Poland
1 shared publication
Latest Publications
- Open Access
- 11 September 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 72 (6) , 151674
Experimental and numerical static tests of tensegrity triplex modules
The paper presents chosen results of experimental tests performed on physical mock-ups of tensegrity triplex modules, approximately 1.2 m tall and of 0.5 m diameter, made of steel. A uniform and uniaxial static compressive loading is applied to three upper nodes of the modules at six different self-stress levels. Cable forces are measured using specially crafted force transducers of an electro-resistive strain-gauge type. Two types of struts with different slenderness are incorporated to analyze the influence of buckling on the behaviour of the modules. A simple three-parameter mathematical model is presented to explain the behaviour of the modules and discuss the obtained experimental data. The results show nonlinear behaviour in the equilibrium path, as well as, rapidly decreasing axial stiffness in the post-critical phase. An increase in prestress has a small influence on the stiffness in the chosen range of compressive loading. The experimental results are valuable for purposes of verification and validation of numerical studies and fill the lack of experimental data in the literature.
- 11 September 2024
- Published by Polish Academy of Sciences Chancellery in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
- Vol. 72 (6) , 151674
Open AccessExperimental and numerical static tests of tensegrity triplex modules
The paper presents chosen results of experimental tests performed on physical mock-ups of tensegrity triplex modules, approximately 1.2 m tall and of 0.5 m diameter, made of steel. A uniform and uniaxial static compressive loading is applied to three upper nodes of the modules at six different self-stress levels. Cable forces are measured using specially crafted force transducers of an electro-resistive strain-gauge type. Two types of struts with different slenderness are incorporated to analyze the influence of buckling on the behaviour of the modules. A simple three-parameter mathematical model is presented to explain the behaviour of the modules and discuss the obtained experimental data. The results show nonlinear behaviour in the equilibrium path, as well as, rapidly decreasing axial stiffness in the post-critical phase. An increase in prestress has a small influence on the stiffness in the chosen range of compressive loading. The experimental results are valuable for purposes of verification and validation of numerical studies and fill the lack of experimental data in the literature.
- Open Access
Determination of the Shear Modulus of Pine Wood with the Arcan Test and Digital Image Correlation
Arcan shear tests with digital image correlation were used to evaluate the shear modulus and shear stress–strain diagrams in the plane defined by two principal axes of the material orthotropy. Two different orientation of the grain direction as compared to the direction of the shear force in specimens were considered: perpendicular and parallel shear. Two different ways were used to obtain the elastic properties based on the digital image correlation (DIC) results from the full-field measurement and from the virtual strain gauges with the linear strains: perpendicular to each other and directed at the angle of π/4 to the shearing load. In addition, the own continuum structural model for the failure analysis in the experimental tests was used. Constitutive relationships of the model were established in the framework of the mathematical multi-surface elastoplasticity for the plane stress state. The numerical simulations done by the finite element program after implementation of the model demonstrated the failure mechanisms from the experimental tests.
Open AccessDetermination of the Shear Modulus of Pine Wood with the Arcan Test and Digital Image Correlation
Arcan shear tests with digital image correlation were used to evaluate the shear modulus and shear stress–strain diagrams in the plane defined by two principal axes of the material orthotropy. Two different orientation of the grain direction as compared to the direction of the shear force in specimens were considered: perpendicular and parallel shear. Two different ways were used to obtain the elastic properties based on the digital image correlation (DIC) results from the full-field measurement and from the virtual strain gauges with the linear strains: perpendicular to each other and directed at the angle of π/4 to the shearing load. In addition, the own continuum structural model for the failure analysis in the experimental tests was used. Constitutive relationships of the model were established in the framework of the mathematical multi-surface elastoplasticity for the plane stress state. The numerical simulations done by the finite element program after implementation of the model demonstrated the failure mechanisms from the experimental tests.
- Open Access
An Orthotropic Elastic-Plastic Constitutive Model for Masonry Walls
The use of a continuum structural model for the analysis of masonry structures in the plane stress state is discussed in this paper. Attention is paid to orthotropic masonry at the material level and validation of the model after its implementation in a proprietary finite element method (FEM) system via user-supplied subroutine. The constitutive relations are established in the framework of the mathematical elastoplasticity theory of small displacements and deformations. Based on the orthotropic failure criterion that was originally proposed by Hoffman in the spatial stress state, the model includes a generalization of the criterion in the plane stress. As it is the case for isotropic quasi-brittle materials, different yield surfaces are considered for tension and compression, which are both of Hoffman type.
Open AccessAn Orthotropic Elastic-Plastic Constitutive Model for Masonry Walls
The use of a continuum structural model for the analysis of masonry structures in the plane stress state is discussed in this paper. Attention is paid to orthotropic masonry at the material level and validation of the model after its implementation in a proprietary finite element method (FEM) system via user-supplied subroutine. The constitutive relations are established in the framework of the mathematical elastoplasticity theory of small displacements and deformations. Based on the orthotropic failure criterion that was originally proposed by Hoffman in the spatial stress state, the model includes a generalization of the criterion in the plane stress. As it is the case for isotropic quasi-brittle materials, different yield surfaces are considered for tension and compression, which are both of Hoffman type.
- 1 December 2017
- Published by Elsevier in Construction and Building Materials
- Vol. 157, 1190-1198
Splitting tensile behavior of autoclaved aerated concrete: Comparison of different specimens’ results
- 1 December 2017
- Published by Elsevier in Construction and Building Materials
- Vol. 157, 1190-1198
Splitting tensile behavior of autoclaved aerated concrete: Comparison of different specimens’ results
- Open Access
- 24 July 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 117, 00114
Soil plasticity with a different porosity
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 24 July 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 117, 00114
Open AccessSoil plasticity with a different porosity
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- Open Access
- 24 July 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 117, 00113
The shear behaviour of pine wood in the Arcan test with the digital image correlation
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 24 July 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 117, 00113
Open AccessThe shear behaviour of pine wood in the Arcan test with the digital image correlation
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 153-157
Determination of Elastic Constants in Brazilian Tests Using Digital Image Correlation
Experimental splitting tension tests of cylindrical specimens made of the Autoclaved Aerated Concrete (AAC) are presented in the paper. Based on results from the digital image correlation system (DIC) and strain gauges, two methods of a determination of the tensile Young's modulus and the Poisson's ratio are discussed, including authors' method. In a new method developed by the authors, it is possible to obtain easy and conveniently both elastic constants simultaneously by fitting the theoretical curve into the displacement field obtained from the DIC system. The fitting curve which is derived based on elasticity theory, describes a distribution of the horizontal displacement along the diameter of the specimen perpendicular to a line of a loading force. Additionally, failure modes and failure mechanisms in the Brazilian splitting test are shown.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 153-157
Determination of Elastic Constants in Brazilian Tests Using Digital Image Correlation
Experimental splitting tension tests of cylindrical specimens made of the Autoclaved Aerated Concrete (AAC) are presented in the paper. Based on results from the digital image correlation system (DIC) and strain gauges, two methods of a determination of the tensile Young's modulus and the Poisson's ratio are discussed, including authors' method. In a new method developed by the authors, it is possible to obtain easy and conveniently both elastic constants simultaneously by fitting the theoretical curve into the displacement field obtained from the DIC system. The fitting curve which is derived based on elasticity theory, describes a distribution of the horizontal displacement along the diameter of the specimen perpendicular to a line of a loading force. Additionally, failure modes and failure mechanisms in the Brazilian splitting test are shown.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 148-152
Detecting Cantilever Beam Vibration with Accelerometers and GNSS
The test shown in this paper is intended to check if the technology of the global navigation satellite systems (GNSS) allows realtime monitoring of more stiffer civil structures with fundamental frequencies about 3-5 Hz and dynamic displacements in the order of a few millimeters. The technical feasibility is illustrated through a simple and inexpensive experiment using a standard stock steel bar to simulate vibration of a building as a vertical cantilever beam. Information on dynamic displacements were obtained both from signals recorded by GNSS receivers and accelerometers. It seems that both instruments can provide sufficiently accurate measurements of relative horizontal displacements allowing dynamic characteristics of the vibrating systems to be accurately identified.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 148-152
Detecting Cantilever Beam Vibration with Accelerometers and GNSS
The test shown in this paper is intended to check if the technology of the global navigation satellite systems (GNSS) allows realtime monitoring of more stiffer civil structures with fundamental frequencies about 3-5 Hz and dynamic displacements in the order of a few millimeters. The technical feasibility is illustrated through a simple and inexpensive experiment using a standard stock steel bar to simulate vibration of a building as a vertical cantilever beam. Information on dynamic displacements were obtained both from signals recorded by GNSS receivers and accelerometers. It seems that both instruments can provide sufficiently accurate measurements of relative horizontal displacements allowing dynamic characteristics of the vibrating systems to be accurately identified.