A. Villar
Research Subjects
Research Interests
A. Villar has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Pedro Jose Arrazola
Mondragon Unibertsitatea
5 shared publications - Ainhara Garay
Mondragon Unibertsitatea
2 shared publications - Francisco Javier Santos
Universidad de Valladolid
1 shared publication I. Llanos
Manufacturing Department, Faculty of Engineering (MGEP) , Mondragon University , Mondragon, Gipuzkoa, Spain
1 shared publicationI. Urresti
Manufacturing Department, Faculty of Engineering (MGEP) , Mondragon University , Mondragon, Gipuzkoa, Spain
1 shared publicationJ. Pujana
1 shared publication
Latest Publications
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 692, 83-92
Machining Apprenticeship Based on Experimental Training Practice
This article describes a practical machining training aiming that the students acquire the theoretical-practical knowledge of chip formation process. The training takes place after theoretical lessons of machining processes. Thus, this practice allows strengthening the knowledge gained during the lessons. The practical training lasts for five hours, and the student assisted by the teacher analyses the influence of some machining entry parameters (cutting speed, feed rate...) on exit parameters like: (I) cutting forces and power consumption, (II) surface roughness, and (III) chip typology. The practical session is carried out on an experimental set-up (Lathe CNC Danobar 65) equipped with sensors and devices to measure forces (sensor Kistler 9121) and power consumption. In addition, a portable rugosimeter (Hommelwerke) is employed to perform surface roughness measurements. No especial devices are needed for the chip typology analysis. In the case of cutting forces and power consumption, the following input parameters influences are analysed: feed rate, depth of cut and cutting speed. In the case of surface roughness analysis, the following input parameters influences are analysed: feed rate and nose radius of the cutting insert. Finally, regarding chip typology feed rate and depth of cut are examined. The experimental results are compared with model predictions (theoretical calculations) for the three issues studied. The students have to compare both results: theoretical an empirical and they need to explain the reasons when discrepancies appear. Results obtained during the last years demonstrate the student acquires better knowledge of the machining process, and at the same time realises of the process complexity.
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 692, 83-92
Machining Apprenticeship Based on Experimental Training Practice
This article describes a practical machining training aiming that the students acquire the theoretical-practical knowledge of chip formation process. The training takes place after theoretical lessons of machining processes. Thus, this practice allows strengthening the knowledge gained during the lessons. The practical training lasts for five hours, and the student assisted by the teacher analyses the influence of some machining entry parameters (cutting speed, feed rate...) on exit parameters like: (I) cutting forces and power consumption, (II) surface roughness, and (III) chip typology. The practical session is carried out on an experimental set-up (Lathe CNC Danobar 65) equipped with sensors and devices to measure forces (sensor Kistler 9121) and power consumption. In addition, a portable rugosimeter (Hommelwerke) is employed to perform surface roughness measurements. No especial devices are needed for the chip typology analysis. In the case of cutting forces and power consumption, the following input parameters influences are analysed: feed rate, depth of cut and cutting speed. In the case of surface roughness analysis, the following input parameters influences are analysed: feed rate and nose radius of the cutting insert. Finally, regarding chip typology feed rate and depth of cut are examined. The experimental results are compared with model predictions (theoretical calculations) for the three issues studied. The students have to compare both results: theoretical an empirical and they need to explain the reasons when discrepancies appear. Results obtained during the last years demonstrate the student acquires better knowledge of the machining process, and at the same time realises of the process complexity.
- 1 January 2010
- Published by Elsevier in CIRP Annals
- Vol. 59 (1) , 97-100
High bandwidth temperature measurement in interrupted cutting of difficult to machine materials
- 1 January 2010
- Published by Elsevier in CIRP Annals
- Vol. 59 (1) , 97-100
High bandwidth temperature measurement in interrupted cutting of difficult to machine materials
- 31 August 2009
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 13 (3) , 385-406
FINITE ELEMENT MODELING OF OBLIQUE MACHINING USING AN ARBITRARY LAGRANGIAN–EULERIAN FORMULATION
A 3D finite element model (FEM) of the oblique chip formation process was proposed in Abaqus/Explicit™ (v6.5) using an Arbitrary Lagrangian Eulerian (ALE) formulation. The sensitivity of the obtained results to variations of tool geometry angles, tool-chip friction, and cutting conditions was analyzed. Experimental tests were carried out on AISI-4140 steel using uncoated cemented carbide tools under oblique cutting conditions for validation of the FEM results, and a good qualitative agreement between them was obtained. The analysis highlighted the need for a proper identification of the friction on the tool-chip interface for the accurate reproduction of the chip formation process by means of finite element modeling.
- 31 August 2009
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 13 (3) , 385-406
FINITE ELEMENT MODELING OF OBLIQUE MACHINING USING AN ARBITRARY LAGRANGIAN–EULERIAN FORMULATION
A 3D finite element model (FEM) of the oblique chip formation process was proposed in Abaqus/Explicit™ (v6.5) using an Arbitrary Lagrangian Eulerian (ALE) formulation. The sensitivity of the obtained results to variations of tool geometry angles, tool-chip friction, and cutting conditions was analyzed. Experimental tests were carried out on AISI-4140 steel using uncoated cemented carbide tools under oblique cutting conditions for validation of the FEM results, and a good qualitative agreement between them was obtained. The analysis highlighted the need for a proper identification of the friction on the tool-chip interface for the accurate reproduction of the chip formation process by means of finite element modeling.
- 1 January 2009
- Published by AIP Publishing in AIP Conference Proceedings
Uncertainty in Yield Stress Coefficient Identification in Two Steels with Different Machinability. Influence on the Modelling of the Chip Formation Process by Finite Elements
Chip Formation process is a complex process, although significant improvements have been reached in the last years, some issues, such as serrated chip formation or residual stresses, remain still obscure. Modelling the chip formation process by finite elements allow us to take into account the non‐linear behaviour of the cutting phenomenon, and hence get information about some variables such as temperature, plastic strain and strain rate that are complicated to be measured by experimental means. There is no doubt that this sort of modelling is making improvements in many fields of machining, e.g., in tools development, cutting conditions selection, but there are some obstacles in its development: (i) the identification of input parameters, (ii) set up of the numerical models and (iii) experimental validation. This paper studies the influence of input parameters in numerical modelling of the chip formation process and particularly the law of workpice behaviour. Two steels with similar composition but different machinability rate have been identified in order to obtain the yield stress coefficient and its uncertainty. Using sensitivity analysis developed in Abaqus/Explicit and proposed in previous works, we get an estimation of the error as a result of the material identification uncertainty. We conclude that it is possible to determine the capability of modelling by finite elements for distinguishing steels with different machinability.
- 1 January 2009
- Published by AIP Publishing in AIP Conference Proceedings
Uncertainty in Yield Stress Coefficient Identification in Two Steels with Different Machinability. Influence on the Modelling of the Chip Formation Process by Finite Elements
Chip Formation process is a complex process, although significant improvements have been reached in the last years, some issues, such as serrated chip formation or residual stresses, remain still obscure. Modelling the chip formation process by finite elements allow us to take into account the non‐linear behaviour of the cutting phenomenon, and hence get information about some variables such as temperature, plastic strain and strain rate that are complicated to be measured by experimental means. There is no doubt that this sort of modelling is making improvements in many fields of machining, e.g., in tools development, cutting conditions selection, but there are some obstacles in its development: (i) the identification of input parameters, (ii) set up of the numerical models and (iii) experimental validation. This paper studies the influence of input parameters in numerical modelling of the chip formation process and particularly the law of workpice behaviour. Two steels with similar composition but different machinability rate have been identified in order to obtain the yield stress coefficient and its uncertainty. Using sensitivity analysis developed in Abaqus/Explicit and proposed in previous works, we get an estimation of the error as a result of the material identification uncertainty. We conclude that it is possible to determine the capability of modelling by finite elements for distinguishing steels with different machinability.
- 1 June 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 202 (1-3) , 475-485
In-process high-speed photography applied to orthogonal turning
- 1 June 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 202 (1-3) , 475-485
In-process high-speed photography applied to orthogonal turning