Jesper Schramm
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jesper Schramm has a total of 121 co-authors. Here are the top co-authors by number of shared publications:
- Kar Mun Pang
Technical University of Denmark
11 shared publications - Rasmus Cordtz
Technical University of Denmark
8 shared publications - Anders Ivarsson
Department of Mechanical Engineering, Technical University of Denmark, Nils Koppels Allé Bld. 403, 2800 Kgs. Lyngby, Denmark
6 shared publications - Hoon Kiat Ng
University of Nottingham Malaysia
5 shared publications - Mehdi Jangi
Lund University
5 shared publications - Suyin Gan
University of Nottingham Malaysia
5 shared publications
Latest Publications
- Open Access
Ignition and combustion study of premixed ammonia using GDI pilot injection in CI engine
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Investigation of Combustion Characteristics, Physical and Chemical Ignition Delay of Methanol Fuel in a Heavy-Duty Turbo-Charged Compression Ignition Engine
In previous research, there have been more investigations on methanol blended with other fuels such as diesel, biodiesel, gasoline, etc., but fewer investigations on methanol with ignition additives as a mono-fuel. To better understand the methanol mono-fuel combustion characteristics and to further apply them, a combined experimental and simulation study of methanol in a Scania heavy-duty compression ignition (CI) engine was carried out in this work. The experiments consisted of four groups with variable injection timings, variable fraction of ignition additives, variable charge air temperatures, and variable overall excess air ratios/power sweeps. Heat release rate (HRR), cylinder pressure, ignition delay and indicated efficiency were analyzed for each case. The analysis showed that the combustion type was partially premixed combustion (PPC) in some cases and diesel-like combustion in the rest. By observing all cases, the shortest ignition delay was 14.1 degrees, and the longest was 22.8 degrees. The indicated efficiencies were in the range of 0.35 to 0.43. Simulations and validation analyses were performed for all cases by a multi-packets model. The physical and chemical ignition delays were predicted. The physical ignition delays were in the range of 4.25 to 8.10 degrees, and the chemical ignition delays were in the range of 6.66 to 17.1 degrees. The chemical ignition delay was always longer than the physical one. This indicates that chemical ignition delay has to be prioritized to improve the ignition performance of methanol fuel.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessInvestigation of Combustion Characteristics, Physical and Chemical Ignition Delay of Methanol Fuel in a Heavy-Duty Turbo-Charged Compression Ignition Engine
In previous research, there have been more investigations on methanol blended with other fuels such as diesel, biodiesel, gasoline, etc., but fewer investigations on methanol with ignition additives as a mono-fuel. To better understand the methanol mono-fuel combustion characteristics and to further apply them, a combined experimental and simulation study of methanol in a Scania heavy-duty compression ignition (CI) engine was carried out in this work. The experiments consisted of four groups with variable injection timings, variable fraction of ignition additives, variable charge air temperatures, and variable overall excess air ratios/power sweeps. Heat release rate (HRR), cylinder pressure, ignition delay and indicated efficiency were analyzed for each case. The analysis showed that the combustion type was partially premixed combustion (PPC) in some cases and diesel-like combustion in the rest. By observing all cases, the shortest ignition delay was 14.1 degrees, and the longest was 22.8 degrees. The indicated efficiencies were in the range of 0.35 to 0.43. Simulations and validation analyses were performed for all cases by a multi-packets model. The physical and chemical ignition delays were predicted. The physical ignition delays were in the range of 4.25 to 8.10 degrees, and the chemical ignition delays were in the range of 6.66 to 17.1 degrees. The chemical ignition delay was always longer than the physical one. This indicates that chemical ignition delay has to be prioritized to improve the ignition performance of methanol fuel.
- 1 December 2020
- Published by Elsevier in Applied Energy
- Vol. 279, 115904
Modeling and analysis of performance and emissions of marine lean-burn natural gas engine propulsion in waves
- 1 December 2020
- Published by Elsevier in Applied Energy
- Vol. 279, 115904
Modeling and analysis of performance and emissions of marine lean-burn natural gas engine propulsion in waves
- Open Access
- 4 June 2020
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 26 (1) , 128-140
Unburned hydrocarbon formation in a natural gas engine under sea wave load conditions
Although natural gas is documented as a low-emission fuel compared to the other traditional fossil fuels in internal combustion engines, recent research indicates large amounts of methane emission released by lean burn gas engines and highlights the importance of this emission on global warming. This paper aims at illustrating the main sources of unburned fuel in internal combustion engines with an emphasis on spark ignited natural gas engines. In addition, two unburned hydrocarbon modeling patterns, empirical and thermodynamic, are proposed. Moreover, a verified engine model including all components with an implemented dynamic load based on harmonic sea waves has been set up and coupled to the unburned hydrocarbon formation models. Results show that load variation may contribute to further methane slip and this increment rises sharply when the load amplitude enlarges. The maximum amount of methane slip occurs at reduced loads when the time lag of the control system of the turbocharger causes additional fresh air to flow towards the combustion chamber and brings the flame into the quenching area. As well, inspecting unburned hydrocarbon emission in diverse air–fuel ratios but with the same wave frequency and amplitude uncovers the sensitivity of lean burn gas engines to the dynamic load.
- 4 June 2020
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 26 (1) , 128-140
Open AccessUnburned hydrocarbon formation in a natural gas engine under sea wave load conditions
Although natural gas is documented as a low-emission fuel compared to the other traditional fossil fuels in internal combustion engines, recent research indicates large amounts of methane emission released by lean burn gas engines and highlights the importance of this emission on global warming. This paper aims at illustrating the main sources of unburned fuel in internal combustion engines with an emphasis on spark ignited natural gas engines. In addition, two unburned hydrocarbon modeling patterns, empirical and thermodynamic, are proposed. Moreover, a verified engine model including all components with an implemented dynamic load based on harmonic sea waves has been set up and coupled to the unburned hydrocarbon formation models. Results show that load variation may contribute to further methane slip and this increment rises sharply when the load amplitude enlarges. The maximum amount of methane slip occurs at reduced loads when the time lag of the control system of the turbocharger causes additional fresh air to flow towards the combustion chamber and brings the flame into the quenching area. As well, inspecting unburned hydrocarbon emission in diverse air–fuel ratios but with the same wave frequency and amplitude uncovers the sensitivity of lean burn gas engines to the dynamic load.
- 8 January 2020
- Published by Wiley in Lubrication Science
- Vol. 32 (3) , 131-144
An experimental investigation of the corrosive influence of SO2 relative to H2SO4 of marine engine cylinder liners
The present study investigates the corrosive influence of SO2 on cylinder liner wear relative to H2SO4. Several charge gases with different concentrations of SO2, H2SO4, and H2O in air are fed to a motored light duty test engine that operates at 98 revolutions per minute (rpm) in order to resemble the corrosive combustion gas and cycle speed of large low‐speed two‐stroke marine engines. When the trapped cylinder gas is compressed, the H2SO4 and H2O vapours can condense on the oil wetted liner surface, and the SO2 can be absorbed in the oil film. Hereby the liner surface may be exposed to a corrosive attack. A blend of a base oil and a commercial marine engine cylinder lubrication oil is used in the experiments. During testing, oil samples are extracted from the engine and subsequently analysed for iron and sulphur accumulation (using an energy dispersive X‐ray fluorescence spectrometer) in order to couple cylinder liner wear with the amount of SO2, H2SO4, and H2O in the charge gas. In contrast to H2SO4, the wear of SO2 is weak (if any), although the SO2 accumulates/reacts considerably in the lube oil. The highest wear rates are found at elevated H2O concentrations.
- 8 January 2020
- Published by Wiley in Lubrication Science
- Vol. 32 (3) , 131-144
An experimental investigation of the corrosive influence of SO2 relative to H2SO4 of marine engine cylinder liners
The present study investigates the corrosive influence of SO2 on cylinder liner wear relative to H2SO4. Several charge gases with different concentrations of SO2, H2SO4, and H2O in air are fed to a motored light duty test engine that operates at 98 revolutions per minute (rpm) in order to resemble the corrosive combustion gas and cycle speed of large low‐speed two‐stroke marine engines. When the trapped cylinder gas is compressed, the H2SO4 and H2O vapours can condense on the oil wetted liner surface, and the SO2 can be absorbed in the oil film. Hereby the liner surface may be exposed to a corrosive attack. A blend of a base oil and a commercial marine engine cylinder lubrication oil is used in the experiments. During testing, oil samples are extracted from the engine and subsequently analysed for iron and sulphur accumulation (using an energy dispersive X‐ray fluorescence spectrometer) in order to couple cylinder liner wear with the amount of SO2, H2SO4, and H2O in the charge gas. In contrast to H2SO4, the wear of SO2 is weak (if any), although the SO2 accumulates/reacts considerably in the lube oil. The highest wear rates are found at elevated H2O concentrations.
- Open Access
- 1 July 2018
- Published by Elsevier in Combustion and Flame
- Vol. 193, 363-383
Modelling of diesel spray flames under engine-like conditions using an accelerated Eulerian Stochastic Field method
- 1 July 2018
- Published by Elsevier in Combustion and Flame
- Vol. 193, 363-383
Open AccessModelling of diesel spray flames under engine-like conditions using an accelerated Eulerian Stochastic Field method
- Open Access
- 1 December 2017
- Published by Elsevier in Energy Procedia
- Vol. 142, 1028-1033
Effects of Nozzle Diameter on Diesel Spray Flames: A numerical study using an Eulerian Stochastic Field Method
- 1 December 2017
- Published by Elsevier in Energy Procedia
- Vol. 142, 1028-1033
Open AccessEffects of Nozzle Diameter on Diesel Spray Flames: A numerical study using an Eulerian Stochastic Field Method
- 15 October 2017
- Published by ASME International
Experimental Investigation of Sulfuric Acid Condensation and Corrosion Rate in Motored BUKH DV24 Diesel Engine
The work conducted in this paper presents a novel experimental setup to study sulfuric acid cold corrosion of cylinder liners in large two-stroke marine diesel engines. The process is simulated in a motored light duty BUKH DV24 diesel engine where the charge air contain known amounts of H2SO4 and H2O vapor. Liner corrosion is measured as iron accumulation in the lube oil. Similarly sulfuric acid condensation is assessed by measuring the accumulation of sulfur in the lube oil. To clarify the corrosive effect of sulfuric acid the lube oil utilized for experiments is a sulfur free neutral oil without alkaline additives (Chevron Neutral Oil 600R). Iron and sulfur accumulation in the lube oil is analyzed with an Energy Dispersive X-Ray Fluorescence (ED-XRF) apparatus. Three test cases with different H2SO4 concentrations are run. Results reveal good agreement between sulfuric acid injection flow and the accumulation of both iron and sulfur in the oil.
- 15 October 2017
- Published by ASME International
Experimental Investigation of Sulfuric Acid Condensation and Corrosion Rate in Motored BUKH DV24 Diesel Engine
The work conducted in this paper presents a novel experimental setup to study sulfuric acid cold corrosion of cylinder liners in large two-stroke marine diesel engines. The process is simulated in a motored light duty BUKH DV24 diesel engine where the charge air contain known amounts of H2SO4 and H2O vapor. Liner corrosion is measured as iron accumulation in the lube oil. Similarly sulfuric acid condensation is assessed by measuring the accumulation of sulfur in the lube oil. To clarify the corrosive effect of sulfuric acid the lube oil utilized for experiments is a sulfur free neutral oil without alkaline additives (Chevron Neutral Oil 600R). Iron and sulfur accumulation in the lube oil is analyzed with an Energy Dispersive X-Ray Fluorescence (ED-XRF) apparatus. Three test cases with different H2SO4 concentrations are run. Results reveal good agreement between sulfuric acid injection flow and the accumulation of both iron and sulfur in the oil.