IBIgor Bezbakh

Igor Bezbakh

*This is an algorithmically generated author record based on publicly available information.

Igor Bezbakh has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Establishing the kinetic regularities and energy efficiency of thermally-treated rice drying considering partial vapor pressure

    by Igor Bezbakh, Lyudmila Phylipova, Igor Yarovyi, Nataliia Veselovska, Yevhen Taranenko, Oleksii Zhelvakov, Sergiy Bezbah, Ganna Goncharuk, Oleg Gaponyk, Elena Marenchenko

    The process of drying thermally treated rice has been considered in this study for different energy supply techniques. The task addressed relates to the high energy intensity of convective drying, the duration of the process, as well as the limitations in existing models that do not take into account the partial pressure of steam as the driving force of the drying process. A bench has been designed for measuring the partial pressure of water vapor over the product based on the data from humidity and temperature sensors. The duration of the system reaching thermodynamic equilibrium is no more than 5 minutes. Accuracy in humidity measurement is ±2–5% RH, humidity measurement limits are 31...100% RH. The kinetics of change in the driving force for different drying techniques were studied. Approximate equations have been obtained that describe the change in the driving force and the kinetics of drying. Specific energy consumption was determined. It was found that the minimum energy consumption corresponds to infrared drying of boiled rice and is 4 MJ/kg, while the convective method is the most energy-intensive at 7.3–9.45 MJ/kg. An equation in similarity numbers (modified Stanton and Euler numbers) has been constructed, which includes the difference in partial water vapor pressures. Low energy consumption in drying boiled rice is explained by the destruction of the cellular structure of the grain during cooking. The energy minimum of infrared drying is due to the supply of heat to the rice by radiation without energy losses on air heating. Real-time measurement of the partial water vapor pressure was used according to the data from humidity and temperature sensors. The studies were conducted on heat-treated (boiled and steamed) rice without husks. The results could be used for making instant dry cereals and ready-made meals. The findings are a tool for scaling up drying equipment and optimizing operating modes

  • Open Access

    Designing the structure and determining the operating parameters of a microwave dehydrator for obtaining phyto-concentrates

    by Oleg Burdo, Igor Bezbakh, Mykola Kepin, Alla Burdo, Igor Yevtushenko, Natalya Bahmutian, Lyudmila Phylipova, Dmytro Kharenko

    This study's object is the process of obtaining phyto-concentrates using a continuous microwave dehydrator. The task addressed is associated with the concentration of food solutions in existing evaporators: product sticking to heat exchange surfaces, change in product quality, the need for additional systems for mixing, high energy consumption, inability to achieve high concentrations. The structure of a microwave dehydrator operates under periodic and continuous modes. The dehydrator's productivity has been determined depending on microwave field power, solution type, as well as product type. Wine, apple, and grape juices; coffee and echinacea extracts, as well as extracts with acetone solvent, were investigated as solutions. For water-containing products, the productivity value varied in the range of 0.28…0.32 kg/h. The dehydrator's operating modes have been defined, enabling the preservation of heat-sensitive components of the raw materials. The highest content of ascorbic acid was found in the concentrate of actinidia berries (375 mg) and bioflavonoids (18.5 mg). The concentrate of grape juice exceeds the control sample (directly squeezed juice) by 6.5 times. The high quality indicators of the product and low energy consumption of the dehydrator are attributed to the selectivity of microwave heating, which has a directed effect on polar molecules of moisture and solvent, without overheating the raw materials. The dehydrator was operated under a continuous mode, which makes it possible to increase productivity, processing quality, reduce metal consumption, and simplify its structure. The energy efficiency of the dehydrator is also based on the fact that due to its use it is possible to exclude a conventional dryer from the technological chain. A feature of the dehydrator design is the lack of need for constant operation of the vacuum pump, which ultimately reduces energy consumption. The scope of its application includes food and processing sectors, production of phyto-concentrates, functional drinks, as well as additives. Conditions of use: small businesses and farms working with heat-sensitive raw materials

  • Open Access

    Причини травматизму працівників у морських портах

    by S.M. Peretiaka, V.M. Palaguta, R.Y. Ivanova, I.V. Bezbakh, Р.ю. Іванова, І.в. Безбах

    Проаналізовано статистичні дані про нещасні випадки у портах України. Розглянуті причини високого рівню травматизму серед портових працівників. Морські порти є одними з найбільш небезпечних робочих місць через високу концентрацію транспорту, важкого обладнання та напруженість праці. Робота в порту може відбуватися в складних погодних умовах, що підвищує ризик травматизму. Фізичне та психологічне навантаження, пов’язане з необхідністю швидкого виконання операцій для забезпечення безперебійного руху вантажів посилює ризик травми. На території порту може спостерігатися підвищений рівень забруднення через викиди від транспорту, пил від перевантаження вантажів та інші фактори, що може негативно впливати на здоров'я працівників. Розраховано значення ризику травмування. Проаналізована ефективність існуючих механізмів захисту і запропоновані головні напрями підвищення безпеки. Наголошено, що важливим елементом попередження нещасних випадків є впровадження системи управління безпекою праці, яка передбачає постійний моніторинг ризиків, регулярні інструктажі та навчання працівників. Додатково варто впроваджувати сучасні технології, що допоможуть автоматизувати контроль за безпекою, такі як сенсори для моніторингу стану обладнання та програмне забезпечення для оцінки ризиків.


  • New constructions of dryers for production of environmentally safe cereal products at reduced specific energy consumption

    by Igor Bezbah, Aleksandr Zykov, Valentyna Bandura, Petr Osadchuk, Yurii Paladiichuk, Igor Mazurenko

    The design of an energy-efficient block grain dryer with evaporative-condensing energy supply systems has been developed. The dryer contains a drying shaft, a condenser, a steam generator that comprise an evaporative-condensing module, and a fan. Design features of the dryer enable to carry out the drying process without direct contact of combustion gases and the product. Analytical modeling of the grain drying process has been carried out. It is based on a two-component model of heat transfer between thermosiphons and a layer of bulk material, taking into account evaporation of moisture from the grain. The efficiency of the developed structure has been evaluated according to such indicators as coefficients of heat transfer to grain flow; specific energy consumption. The values of coefficients of heat transfer to grain flow are 60 Wm-2K-1. An increase in the grain flow rate leads to an increase in the heat transfer coefficient. Energy costs approach the minimum when drying at the temperature of the surface of thermosiphons Ts=140 °С for different grain consumptions. Energy consumption is 3.3...5.15 MJ/kg, depending on the surface temperature and air consumption


  • Open Access

    Innovative methods of drying rapeseeds using microwave energy

    by Valentyna Bandura, Igor Bezbah, Ihor Kupchuk, Larisa Fialkovska

    Rape is an important oil crop with a wide range of uses. Harvested rapeseed must be cleaned and dried before processing. The process of drying rapeseed as a small-seeded crop has its own specifics. One of the new drying methods is the use of microwave radiation, the disadvantage of which is...


  • Open Access

    Designing the structure and determining the mode characteristics of the grain dryer based on thermosiphons

    by Igor Bezbah, Aleksandr Zykov, Vsevolod Mordynskyi, Petr Osadchuk, Lyudmila Phylipova, Valentyna Bandura, Igor Yarovyi, Elena Marenchenko

    Energy consumption, environmental issues, product quality are actual problems related to grain drying processes. It is necessary to pay attention to designing new structures of energy-efficient grain dryers. A structure of an energy-efficient grain dryer based on thermosiphons has been designed; its energy consumption is 3.5...6.8 MJ/kg depending on surface temperature and air flow rate. The dryer includes a layer heater, a drying chamber, a heat generator, a heater, a noria for loading the product, and fans. The structural features of the dryer allow the drying process to be carried out without direct contact between the combustion gases and the product. The efficiency of the designed structure was evaluated for such indicators as heat transfer coefficients to the grain flow, specific energy costs, moisture content, the relative humidity of the air leaving the dryer. The values of coefficients of the heat transfer to the grain flow vary within 36...58 W/m2K at speeds 2.5...8 mm/s. An increase in the flow rate by 3.2 times leads to an increase in the heat transfer coefficient by 1.6 times. The moisture content of the air at the outlet of the dryer reaches 60 g/kg, while the relative humidity is 90 %, which is several times higher than the parameters for convective mine grain dryers. Energy consumption for drying at the surface temperature of thermosiphons Ts=142.9 °C for various grain flow rates is close to a minimum. The energy consumption is lower than in existing convective dryers. 21 % is spent on heating grain in the dryer; 54 % ‒ on moisture evaporation; and 23.6 % are losses. If we consider the energy spent on moisture evaporation usable, the efficiency of convective dryers is only 40 % while that of dryers based on thermosiphons is 54.1 %. It is expected that the designed structure could be a solution for small farmers in the post-harvest drying process


  • Open Access

    Development of the design and determination of mode characteristics of block cryoconcentrators for pomegranate juice

    by Oleg Burdo, Igor Bezbakh, Aleksandr Zykov, Yana Fatieieva, Davar Rostami Pour, Petr Osadchuk, Igor Mazurenko, Shao Zhengzheng, Lyudmila Phylipova

    The designs of cryoconcentrators of block type BV-2 and BL-20 have been developed. The influence of design and operating parameters on the kinetics of freezing of pomegranate juice was investigated. A decrease in the operating temperature of the refrigeration unit contributes to a more intensive growth of the ice block. When the temperature of the coolant decreases by 1.2 times, the productivity of the BV-2 unit increases by 27 %, and of the BL-20 unit by 12 %. For BL-20, an increase in the initial concentration by 3 times leads to a decrease in productivity by 2.5...1.5 times. The influence of the temperature of the coolant and the initial concentration of the juice on the rate of concentration change has been determined. At low initial concentrations of solutions (10...15 %), a sharp increase in concentration is observed at the final stage of freezing. The dry matter content of the juice is increased by 16 % at high concentrations, only 4 %. The kinetics of the ice block separation process has been studied. At the first stage (duration 10...15 minutes), the concentration of effluents is 2...3 % higher than the concentration of the solution. On the second, increases by 6...10 %. In the third stage, there is a monotonous decrease in effluent concentration (2.5 % / hour). The results of experimental modeling are generalized. The obtained equation in similarity numbers allows calculating the mass transfer coefficients with an error of no more than 20 %. The developed designs of the BL-20 and BV-2 cryoconcentrators are semi-industrial units. With block cryoconcentration, a concentration of pomegranate juice of 47° Brix was achieved, which is higher than in traditional devices. The results obtained can be applied for further development and creation of industrial plants with optimal improved product parameters.


  • Open Access

    Development of the design and determination of the mode characteristics of the demineralizer for sea water

    by Oleg Burdo, Igor Bezbakh, Yana Fatieieva, Aleksandr Zykov, Petr Osadchuk, Igor Mazurenko, Shao Zhengzheng, Lyudmila Phylipova

    The object of research is block low-temperature installations for obtaining fresh water. Investigated problem: obtaining fresh water from sea using low-temperature technologies. Main scientific results: the design is developed and the operating characteristics of the demineralizer for sea water are determined. The influence of the initial salt content of sea water on the ice formation rate is determined. With an increase in the salinity of 3.5 times, productivity on ice decreases 2.3 times. The kinetics of the salt content in the freezing solution depends on the initial concentration. With an initial salt content of 6.74 g/l, the process rate is 0.4 g/h, with a salt content of 1 g/l – 0.14 g/h With an initial salt content of 6.74 g/l, the process of separating wastewater from the ice block is more intensive. The salt content of the first portion of the effluent is 3.2 times higher than the initial concentration of the solution. A cryoscopic curve was obtained for seawater in the concentration range from 0 to 6.74 g/l. The area of practical use of the research results: studies of the quality of the obtained water showed that the content of nitrates decreases 5 times, the hardness decreases by 2 mg/dm³. The salt content is reduced from 858 mg/dm³ to 560 mg/dm³. Plants for the concentration of food liquids by the block freezing method are designed to produce environmentally friendly products that preserve the bioactive complex of raw materials as much as possible with minimal energy consumption. An innovative technological product: design and operating modes of a block freezing plant for seawater desalination. Scope of application of the innovative technological product: industrial enterprises, the technological process of which requires small volumes of fresh water; to obtain fresh water on oil platforms in the oceans; small hotels, boarding houses on the seaside.

  • Open Access

    DEVELOPMENT OF A CONCEPTUAL MODEL OF A ROBOTIC COMPLEX FOR THE PRODUCTION OF RAVIOLI OF SPECIAL FORMS

    by Oleg Burdo, Igor Bezbakh, Pavel Golubkov, Serhii Shyshov, Aleksander Gavrilov, Sergey Terziev, Tetiana Nedobiichuk

    The article provides a substantiation of the conceptual model of the production process of special forms of dumplings. It is the first stage in the development of a model of this process as a control object. The purpose of which is to form an objective basis for the development of an effective system for automatic process control. The development of the conceptual model presupposes the specification and description of the properties of control channels and acting disturbances to the level of their mathematical model, which can be implemented in a simulation environment. Problems of identification of the mathematical model of the process of the production of dumplings, i. e. obtaining a mathematical description of processes based on the results of its purposeful experimental research, due to its complexity as a control object.The experimental approach, in this case, gives much more reliable results on the properties of the process. An attempt to obtain such general properties on the basis of experimental data would inevitably lead to the need for very complex and lengthy multifactorial experiments and nontrivial procedures for their processing. But this will leave open the question of the adequacy of the model for those conditions of the process and types of raw materials that were not covered by the experiments. Fundamentally important is the fact that the mathematical model of the process is developed as a model of the control object.Model can be used in two ways. This is due to the fact that in the closed circuits of the SAC, the discrepancy between the models can be considered as a manifestation of uncontrolled coordinate and parametric disturbances. It is in conditions of this kind of disturbances that the SAC must fulfill its functional purpose. The developed mathematical model of the production process of special forms of dumplings will be used by us only in the direction, when it is of great importance not so much quantitative as its qualitative correspondence to the original object.

  • Open Access

    Development of power­efficient and environmentally safe coffee product technologies

    by Oleg Burdo, Igor Bezbakh, Aleksandr Zykov, Sergey Terziev, Aleksander Gavrilov, Ilya Sirotyuk, Igor Mazurenko, Yunbo Li

    Development of power­efficient and environmentally safe coffee product technologies