Nasser H. Shalaby
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nasser H. Shalaby has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Salah A. Hassan
Ain Shams University
4 shared publicationsSamia A. Hanafi
Egyptian Petroleum Research Institute, Nasr City, Cairo, Egypt
4 shared publicationsMamdouh S. Elmelawy
Egyptian Petroleum Research Institute, Nasr City, Cairo, Egypt
3 shared publications- Ahmed Mohamed Alsabagh
Egyptian Petroleum Research Institute (EPRI)
2 shared publications - Ahmed. H. Ragab
Department of Chemistry, Faculty of Science, King Khalid University, Abha 62224, Saudi Arabia
2 shared publications Hamdi A. Hassan
2 shared publications
Latest Publications
- Open Access
Waste-Extracted Zn and Ag Co-Doped Spent Catalyst-Extracted V2O5 for Photocatalytic Degradation of Congo Red Dye: Effect of Metal-Nonmetal Co-Doping
The current study applies the eco-friendly principle of “wastes treat wastes”. By swift methods, a composite photocatalyst was prepared from waste-extracted oxides, namely V2O5, Ag, and ZnO. The metal–lixiviant complexes were used as metal precursors, where the lixiviants act as auto-templates and increase the compatibility between the mixed metallic species, and their controlled thermal removal generates pores. The tri-constitute composite catalyst was doped with nitrogen. The constitution, surface composition, and optical properties of the doped catalysts were investigated by XRD, SEM, TEM, BET surface analysis, XPS, diffuse reflectance, and PL spectra. The as-prepared catalysts were employed in the photodegradation of Congo red dye (CR) under visible irradiation at ambient temperature. The degree of Ag dispersion had a significant effect on the bandgap, as did metal and metal-nonmetal co-doping. The efficiency of dye removal changes dramatically with time up to 120 min, after which it begins to decrease. According to the pH effect, the normal pH of Congo red dye (6.12) is optimal. At a catalyst dose of 1 g L−1 and an irradiation period of 120 min, photodegradation efficiency reached 89.9% and 83.4% over [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively. The kinetic study depicted the significant role of mass transfer in the reaction rate. The obtained rate constants were 0.995 mole L−1 S−1 and 0.998 mole L−1 S−1 for [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively.
Open AccessWaste-Extracted Zn and Ag Co-Doped Spent Catalyst-Extracted V2O5 for Photocatalytic Degradation of Congo Red Dye: Effect of Metal-Nonmetal Co-Doping
The current study applies the eco-friendly principle of “wastes treat wastes”. By swift methods, a composite photocatalyst was prepared from waste-extracted oxides, namely V2O5, Ag, and ZnO. The metal–lixiviant complexes were used as metal precursors, where the lixiviants act as auto-templates and increase the compatibility between the mixed metallic species, and their controlled thermal removal generates pores. The tri-constitute composite catalyst was doped with nitrogen. The constitution, surface composition, and optical properties of the doped catalysts were investigated by XRD, SEM, TEM, BET surface analysis, XPS, diffuse reflectance, and PL spectra. The as-prepared catalysts were employed in the photodegradation of Congo red dye (CR) under visible irradiation at ambient temperature. The degree of Ag dispersion had a significant effect on the bandgap, as did metal and metal-nonmetal co-doping. The efficiency of dye removal changes dramatically with time up to 120 min, after which it begins to decrease. According to the pH effect, the normal pH of Congo red dye (6.12) is optimal. At a catalyst dose of 1 g L−1 and an irradiation period of 120 min, photodegradation efficiency reached 89.9% and 83.4% over [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively. The kinetic study depicted the significant role of mass transfer in the reaction rate. The obtained rate constants were 0.995 mole L−1 S−1 and 0.998 mole L−1 S−1 for [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively.
- Open Access
- 27 November 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (6) , 7425-7436
Photocatalytic Performance of Organically Templated Cr-Doped Co3O4 in Remediation of Industrial Wastewater: Effect of Order–Disorder in the Lattice
In photocatalysis, the optical properties and surface parameters significantly affect the catalytic performance. To engineer the optical properties and textural structure, Cr and p-phenylene diamine (PDA) were utilized as dopant and textural structure regulator, respectively. A series of Cr-doped Co3O4 with dopant percentages of 0, 1, 3, and 5, templated PDA at a fixed ratio of 5%, and another un-templated sample with a dopant ratio of 5% were prepared. The co-precipitation method was applied in swift and innovative procedures, where a calculated amount of NaOH was used as a precipitant. The optical properties, dopant concentration quenching, and surface parameters are strongly affected by the order–disorder in the lattice and dopant concentration. The lattice regularity affects the optical properties and the surface parameters along with the dopant concentration. The photocatalysts were evaluated in the disposal of organic pollutants in a representative sample of wastewater collected from different industrial activities. The function of another function was applied to monitor the pollutants' disposal, taking the total organic carbon (TOC) as a function of the pollutants' concentration and the photometric absorbance as a function of the TOC. The kinetic investigation exhibited the significant role of the pore system on the reaction rate.
- 27 November 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (6) , 7425-7436
Open AccessPhotocatalytic Performance of Organically Templated Cr-Doped Co3O4 in Remediation of Industrial Wastewater: Effect of Order–Disorder in the Lattice
In photocatalysis, the optical properties and surface parameters significantly affect the catalytic performance. To engineer the optical properties and textural structure, Cr and p-phenylene diamine (PDA) were utilized as dopant and textural structure regulator, respectively. A series of Cr-doped Co3O4 with dopant percentages of 0, 1, 3, and 5, templated PDA at a fixed ratio of 5%, and another un-templated sample with a dopant ratio of 5% were prepared. The co-precipitation method was applied in swift and innovative procedures, where a calculated amount of NaOH was used as a precipitant. The optical properties, dopant concentration quenching, and surface parameters are strongly affected by the order–disorder in the lattice and dopant concentration. The lattice regularity affects the optical properties and the surface parameters along with the dopant concentration. The photocatalysts were evaluated in the disposal of organic pollutants in a representative sample of wastewater collected from different industrial activities. The function of another function was applied to monitor the pollutants' disposal, taking the total organic carbon (TOC) as a function of the pollutants' concentration and the photometric absorbance as a function of the TOC. The kinetic investigation exhibited the significant role of the pore system on the reaction rate.
- 21 February 2022
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 104 (7) , 1595-1609
One-step catalytic pyrolysis of pre-treated rice straw to biofuel over waste-extracted Ni–H 3 PW 12 O 40 activated nano-catalyst
Alternative, renewable and carbon-neutral fuels are an urgent requirement. Pyrolysis has received the most attention in the conversion of biomass into fuel. The main disadvantages of chemical and physical properties of pyrolysis crude bio-oil include its high oxygen content and acidity. Catalytic fast pyrolysis can overcome this problem. Rice straw is an abundant biomass residual that can be of environmental negative impact and is not of proper use. Therefore, this research work introduces the use of this residual in the production of fuel sources by one-step catalytic pyrolysis with the reusability of the employed catalyst. A waste extraction catalyst modified with acidic and nickel sites has been prepared and was utilised for the proposed target in this study. The removal of silica, lignin and minerals by treatment of the rice straw with KOH and then HNO3 in a green terminated process improved the catalytic biomass conversion from 83% to 96% at a catalyst dose of 5%, at 250°C. The pre-treatment of the rice straw enables the reusability of the catalyst in direct catalytic pyrolysis where the employed catalyst exhibits good stability in four consecutive runs. The used KOH and HNO3 were neutralised by mixing to produce KNO3 as a valuable fertiliser.
- 21 February 2022
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 104 (7) , 1595-1609
One-step catalytic pyrolysis of pre-treated rice straw to biofuel over waste-extracted Ni–H 3 PW 12 O 40 activated nano-catalyst
Alternative, renewable and carbon-neutral fuels are an urgent requirement. Pyrolysis has received the most attention in the conversion of biomass into fuel. The main disadvantages of chemical and physical properties of pyrolysis crude bio-oil include its high oxygen content and acidity. Catalytic fast pyrolysis can overcome this problem. Rice straw is an abundant biomass residual that can be of environmental negative impact and is not of proper use. Therefore, this research work introduces the use of this residual in the production of fuel sources by one-step catalytic pyrolysis with the reusability of the employed catalyst. A waste extraction catalyst modified with acidic and nickel sites has been prepared and was utilised for the proposed target in this study. The removal of silica, lignin and minerals by treatment of the rice straw with KOH and then HNO3 in a green terminated process improved the catalytic biomass conversion from 83% to 96% at a catalyst dose of 5%, at 250°C. The pre-treatment of the rice straw enables the reusability of the catalyst in direct catalytic pyrolysis where the employed catalyst exhibits good stability in four consecutive runs. The used KOH and HNO3 were neutralised by mixing to produce KNO3 as a valuable fertiliser.
- 18 November 2021
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 103 (20) , 8941-8956
Stover ash - extracted mixed oxides surface-doped with Ni for photo-degradation of water organic pollutants
The mesoporous catalytic composite material was prepared from both stover ash (as a source of mixed oxides) and treated rice straw with very low residue on ignition (as a pore-capping agent). X-ray diffraction and BET surface analyses of the as-prepared mesoporous mixed oxides (MMO) exhibited a partially crystalline structure with an average pore diameter of 16.4 nm. To modify the optical properties, Ni nanoparticles were loaded onto the MMO surface via the reduction with hydrazine. Both MMO and the modified material, namely Ni-MMO, were investigated by HR-TEM, IR, X-ray diffraction, BET surface analyses, XPS, PL spectra, and UV-Visible reflectance measurements. In a good agreement, all tests confirmed that Ni nanoparticles interacted with oxides on the surface with restructuring and a new potential crystal system. XPS revealed that Ni generates surface oxygen vacancies (SOV) which induced sub-band levels to stabilise e-/h* pairs. Ni-MMO with low PL intensity showed a high photocatalytic activity in degradation of Rhodamine B dye with a maximum of 99.1% after 180 min under visible irradiation and catalyst dose of 1 g L−1. The reusability test for Ni-MMO exhibits the catalyst stability in four consecutive cycles.
- 18 November 2021
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 103 (20) , 8941-8956
Stover ash - extracted mixed oxides surface-doped with Ni for photo-degradation of water organic pollutants
The mesoporous catalytic composite material was prepared from both stover ash (as a source of mixed oxides) and treated rice straw with very low residue on ignition (as a pore-capping agent). X-ray diffraction and BET surface analyses of the as-prepared mesoporous mixed oxides (MMO) exhibited a partially crystalline structure with an average pore diameter of 16.4 nm. To modify the optical properties, Ni nanoparticles were loaded onto the MMO surface via the reduction with hydrazine. Both MMO and the modified material, namely Ni-MMO, were investigated by HR-TEM, IR, X-ray diffraction, BET surface analyses, XPS, PL spectra, and UV-Visible reflectance measurements. In a good agreement, all tests confirmed that Ni nanoparticles interacted with oxides on the surface with restructuring and a new potential crystal system. XPS revealed that Ni generates surface oxygen vacancies (SOV) which induced sub-band levels to stabilise e-/h* pairs. Ni-MMO with low PL intensity showed a high photocatalytic activity in degradation of Rhodamine B dye with a maximum of 99.1% after 180 min under visible irradiation and catalyst dose of 1 g L−1. The reusability test for Ni-MMO exhibits the catalyst stability in four consecutive cycles.
- Open Access
Phragmites australis (Reed) as an Efficient, Eco-Friendly Adsorbent for Brackish Water Pre-Treatment in Reverse Osmosis: A Kinetic Study
A cost-effective adsorbent was prepared by carbonization of pre-treated Phragmites australis reed at 500 °C. Phragmites australis was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) surface analyses. XRD of the as-prepared adsorbent exhibited a partially crystalline structure with a specific surface area of 211.6 m2/g and an average pore diameter of 4.2 nm. The biosorption potential of novel biosorbent Phragmites australis reed was investigated with a batch scale and continuous flow study. The study was conducted at different constraints to obtain optimum pH conditions, adsorbent dose, contact time, agitation speed, and initial TDS concentration. In order to analyze the properties of the procedure and determine the amount of sodium removal, Langmuir, Freundlich, and Dubinin–Radushkevich isotherms were tested. The optimal values of contact time, pH, and adsorbent dose were found to be 150 min, 4, and 10 g/L, respectively, with an agitation speed of 300 rpm at room temperature (27 °C). The three tested isotherms show that the adsorption of Na+ onto the prepared adsorbent is a hybrid process from physi- and chemisorption. For industrial application, the adsorbent was tested using the adsorbent column technique. Pseudo-first-order, pseudo-second-order, and diffusion models were connected, and it was discovered that the information fit best to the pseudo-second-arrange active model. According to the intraparticle diffusion model, the mechanism goes through four stages before reaching equilibrium. The periodicity test shows that the adsorption ability of Phragmites australis can be recovered by washing with 0.1 M HCl.
Open AccessPhragmites australis (Reed) as an Efficient, Eco-Friendly Adsorbent for Brackish Water Pre-Treatment in Reverse Osmosis: A Kinetic Study
A cost-effective adsorbent was prepared by carbonization of pre-treated Phragmites australis reed at 500 °C. Phragmites australis was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) surface analyses. XRD of the as-prepared adsorbent exhibited a partially crystalline structure with a specific surface area of 211.6 m2/g and an average pore diameter of 4.2 nm. The biosorption potential of novel biosorbent Phragmites australis reed was investigated with a batch scale and continuous flow study. The study was conducted at different constraints to obtain optimum pH conditions, adsorbent dose, contact time, agitation speed, and initial TDS concentration. In order to analyze the properties of the procedure and determine the amount of sodium removal, Langmuir, Freundlich, and Dubinin–Radushkevich isotherms were tested. The optimal values of contact time, pH, and adsorbent dose were found to be 150 min, 4, and 10 g/L, respectively, with an agitation speed of 300 rpm at room temperature (27 °C). The three tested isotherms show that the adsorption of Na+ onto the prepared adsorbent is a hybrid process from physi- and chemisorption. For industrial application, the adsorbent was tested using the adsorbent column technique. Pseudo-first-order, pseudo-second-order, and diffusion models were connected, and it was discovered that the information fit best to the pseudo-second-arrange active model. According to the intraparticle diffusion model, the mechanism goes through four stages before reaching equilibrium. The periodicity test shows that the adsorption ability of Phragmites australis can be recovered by washing with 0.1 M HCl.
- 13 June 2021
- Published by Springer Nature in Journal of Porous Materials
- Vol. 28 (5) , 1553-1562
Electrostatic immobilization of ionic liquids onto SBA-15 as heterogenized catalysts for esterification of oleic acid with trimethylolpropane
- 13 June 2021
- Published by Springer Nature in Journal of Porous Materials
- Vol. 28 (5) , 1553-1562
Electrostatic immobilization of ionic liquids onto SBA-15 as heterogenized catalysts for esterification of oleic acid with trimethylolpropane
- 23 May 2018
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 58 (5) , 387-394
Can Mesoporous TiO2-Al2O3-Supported NiMoS OR CoMoS Effectively Perform in Ultra-Deep Desulfurization of Gas Oil?
Waste aluminum foil was used for preparation of mesoporous TiO2-Al2O3using starch as a textural modifier. The catalytic species, Mo and Ni or Co were loaded onto the mesoporous support, following...
- 23 May 2018
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 58 (5) , 387-394
Can Mesoporous TiO2-Al2O3-Supported NiMoS OR CoMoS Effectively Perform in Ultra-Deep Desulfurization of Gas Oil?
Waste aluminum foil was used for preparation of mesoporous TiO2-Al2O3using starch as a textural modifier. The catalytic species, Mo and Ni or Co were loaded onto the mesoporous support, following...
- 1 January 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (1) , 22-32
A study on optimization of acid sites concentration versus pore dimensions in modified solid acid catalysts for biodiesel production
The acid sites concentration of silica sulfuric acid was optimized against pore dimensions depending on the intensity of silanol groups as a key for binding modifier molecules. The texturally modified rice husk silica, of determined intensity of silanol groups, was functionalized with different loadings of SO3H groups to produce solid acid catalysts with different concentrations of acid sites and different sizes of the pore systems. The catalysts were employed in trans-esterification of waste-cocking oil. The obtained optimum catalytic activity was attributed to the proper compensation between acid sites intensity and pore dimensions. The estimated TOF for methyl ester production was found to decrease with the increase of SO3H loading on the catalyst surface. The role of compatibility of the reactants phase with the catalyst nature could be validated by the observed much higher activity of sulfonated lignin in the studied esterification reaction than the modified RHS-acid catalysts under study.
- 1 January 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (1) , 22-32
A study on optimization of acid sites concentration versus pore dimensions in modified solid acid catalysts for biodiesel production
The acid sites concentration of silica sulfuric acid was optimized against pore dimensions depending on the intensity of silanol groups as a key for binding modifier molecules. The texturally modified rice husk silica, of determined intensity of silanol groups, was functionalized with different loadings of SO3H groups to produce solid acid catalysts with different concentrations of acid sites and different sizes of the pore systems. The catalysts were employed in trans-esterification of waste-cocking oil. The obtained optimum catalytic activity was attributed to the proper compensation between acid sites intensity and pore dimensions. The estimated TOF for methyl ester production was found to decrease with the increase of SO3H loading on the catalyst surface. The role of compatibility of the reactants phase with the catalyst nature could be validated by the observed much higher activity of sulfonated lignin in the studied esterification reaction than the modified RHS-acid catalysts under study.
- 1 July 2017
- Published by Springer Nature in Refractories and Industrial Ceramics
- Vol. 58 (2) , 136-144
Insulating Refractory Bricks from Water Treatment Sludge and Rice Husk Ash
- 1 July 2017
- Published by Springer Nature in Refractories and Industrial Ceramics
- Vol. 58 (2) , 136-144
Insulating Refractory Bricks from Water Treatment Sludge and Rice Husk Ash