Józef Lelątko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Józef Lelątko has a total of 134 co-authors. Here are the top co-authors by number of shared publications:
- Tomasz Goryczka
Institute of Materials Science, University of Silesia in Katowice, 75 Pułku Piechoty 1A, 41-500 Chorzów, Poland
23 shared publications Henryk Morawiec
University of Silesia
10 shared publicationsH. Morawiec
University of Silesia, Institute of Material Science, 40‐007 Katowice, Bankowa 12, Poland
9 shared publications- Tadeusz Wierzchoń
Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland
9 shared publications - Jaroslaw Polanski
Institute of Chemistry, University of Silesia, 75 Pułku Piechoty 1a, 41-500 Chorzow, Poland
7 shared publications - Danuta Stróż
Institute of Materials Engineering, University of Silesia in Katowice, 75 Pułku Piechoty 1A St., 41-500 Chorzów, Poland
6 shared publications
Latest Publications
- 1 December 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (15) , 5010-5017
Structure and luminescent properties of oxyfluoride glass-ceramics with YF3:Eu3+ nanocrystals derived by sol-gel method
- 1 December 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (15) , 5010-5017
Structure and luminescent properties of oxyfluoride glass-ceramics with YF3:Eu3+ nanocrystals derived by sol-gel method
- 1 May 2019
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 60 (5) , 693-697
Structure and Mechanical Properties of Multi-Functional Layer Deposited on Surface of Ni–Ti Shape Memory Alloy
A thin layer, about 25 nm thick, was produced in glow discharge deposition process on the surface of the NiTi shape memory alloy. Structural and chemical studies revealed that the layer consisted of two sublayers. About 7 nm thick one, adhering closely to the NiTi substrate and formed from the nanocrystalline titanium nitride was followed by 17 nm of the amorphous titanium oxide layer. The technological parameters of the glow discharge process caused that the presence of the R-phase in the matrix was identified.
- 1 May 2019
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 60 (5) , 693-697
Structure and Mechanical Properties of Multi-Functional Layer Deposited on Surface of Ni–Ti Shape Memory Alloy
A thin layer, about 25 nm thick, was produced in glow discharge deposition process on the surface of the NiTi shape memory alloy. Structural and chemical studies revealed that the layer consisted of two sublayers. About 7 nm thick one, adhering closely to the NiTi substrate and formed from the nanocrystalline titanium nitride was followed by 17 nm of the amorphous titanium oxide layer. The technological parameters of the glow discharge process caused that the presence of the R-phase in the matrix was identified.
- 1 March 2019
- Published by Elsevier in Optical Materials
- Vol. 89, 276-282
Reddish-orange Eu3+-doped sol-gel emitters based on LaF3 nanocrystals – Synthesis, structural and photoluminescence investigations
- 1 March 2019
- Published by Elsevier in Optical Materials
- Vol. 89, 276-282
Reddish-orange Eu3+-doped sol-gel emitters based on LaF3 nanocrystals – Synthesis, structural and photoluminescence investigations
- 12 March 2018
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 51 (2) , 411-419
Paracrystalline structure of gold, silver, palladium and platinum nanoparticles
Metallic nanoparticles are of great importance because of their unique physical, chemical, antimicrobial, diagnostic, therapeutic, biomedical, sensing, biosensing, catalytic and optical properties. Detailed knowledge of the atomic scale structure of these materials is essential for understanding their activities and for exploiting their potential. This paper reports structural studies of silica-supported silver, gold, palladium and platinum nanoparticles using X-ray diffraction and high-resolution transmission electron microscopy. Electron microscopy observation allowed the determination of nanoparticle sizes, which were estimated to be in the range of 45–470 Å, and their distribution. The obtained histograms exhibit a multimodal distribution of the investigated nanoparticle sizes. The X-ray diffraction data were analyzed using the Rietveld method in the form of Williamson–Hall plots, the PDFgui fitting procedure and model-based simulation. The Williamson–Hall plots provide evidence for the presence of strain in all investigated samples. The PDFgui fitting results indicate that the investigated nanoparticles consist of atomic clusters with different sizes and degrees of disorder as well as slightly different lattice parameters. The detailed structural characterization performed via model-based simulations proves that all samples exhibit a face-centered cubic type structure with paracrystalline distortion. The degree of disorder predicted by the paracrystalline theory is correlated with the sizes of the nanoparticles. The catalytic properties of the investigated noble metals are discussed in relation to their disordered structure.
- 12 March 2018
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 51 (2) , 411-419
Paracrystalline structure of gold, silver, palladium and platinum nanoparticles
Metallic nanoparticles are of great importance because of their unique physical, chemical, antimicrobial, diagnostic, therapeutic, biomedical, sensing, biosensing, catalytic and optical properties. Detailed knowledge of the atomic scale structure of these materials is essential for understanding their activities and for exploiting their potential. This paper reports structural studies of silica-supported silver, gold, palladium and platinum nanoparticles using X-ray diffraction and high-resolution transmission electron microscopy. Electron microscopy observation allowed the determination of nanoparticle sizes, which were estimated to be in the range of 45–470 Å, and their distribution. The obtained histograms exhibit a multimodal distribution of the investigated nanoparticle sizes. The X-ray diffraction data were analyzed using the Rietveld method in the form of Williamson–Hall plots, the PDFgui fitting procedure and model-based simulation. The Williamson–Hall plots provide evidence for the presence of strain in all investigated samples. The PDFgui fitting results indicate that the investigated nanoparticles consist of atomic clusters with different sizes and degrees of disorder as well as slightly different lattice parameters. The detailed structural characterization performed via model-based simulations proves that all samples exhibit a face-centered cubic type structure with paracrystalline distortion. The degree of disorder predicted by the paracrystalline theory is correlated with the sizes of the nanoparticles. The catalytic properties of the investigated noble metals are discussed in relation to their disordered structure.
- 1 June 2017
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 206, 16-23
Oxide passivated Ni-supported Ru nanoparticles in silica: A new catalyst for low-temperature carbon dioxide methanation
- 1 June 2017
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 206, 16-23
Oxide passivated Ni-supported Ru nanoparticles in silica: A new catalyst for low-temperature carbon dioxide methanation
- 1 January 2017
- Published by Elsevier in Materials Characterization
- Vol. 123, 256-263
Impact of microstructure on the thermoelectric properties of the ternary compound Ce 3 Cu 3 Sb 4
- 1 January 2017
- Published by Elsevier in Materials Characterization
- Vol. 123, 256-263
Impact of microstructure on the thermoelectric properties of the ternary compound Ce 3 Cu 3 Sb 4
- 1 October 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 130 (4) , 1094-1096
Effect of Creep on Crystallographic Orientation in Single Crystal Superalloy
- 1 October 2016
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 130 (4) , 1094-1096
Effect of Creep on Crystallographic Orientation in Single Crystal Superalloy
- 21 April 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 687, 19-24
The Structure and Shape Memory of the Hot Extruded NiTi Alloy
The paper presents results of structural studies of hot extruded NiTi shape memory alloy that is in the B2 phase at room temperature. Texture of the alloy was determined from the X-ray diffraction measurements. It was found that in result of 60 % sample reduction (at a cross-section of a bar formed by hot extrusion) weak axial texture - type B2 was formed. The volume of the grains oriented in this way was approx. 20 %. Basing on metallographic observations it was also found that the size of the grains formed as a result of the thermomechanical treatment was uniform with the average area of 1700 μm2. This information is significant from the point of view of functional properties. Hot extruded alloy revealed presence of the reversible martensitic transformation. Its characteristic temperatures were slight higher than in as-cast alloy. Moreover, the extruded NiTi alloy showed 100 % of the shape recovery.
- 21 April 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 687, 19-24
The Structure and Shape Memory of the Hot Extruded NiTi Alloy
The paper presents results of structural studies of hot extruded NiTi shape memory alloy that is in the B2 phase at room temperature. Texture of the alloy was determined from the X-ray diffraction measurements. It was found that in result of 60 % sample reduction (at a cross-section of a bar formed by hot extrusion) weak axial texture - type B2 was formed. The volume of the grains oriented in this way was approx. 20 %. Basing on metallographic observations it was also found that the size of the grains formed as a result of the thermomechanical treatment was uniform with the average area of 1700 μm2. This information is significant from the point of view of functional properties. Hot extruded alloy revealed presence of the reversible martensitic transformation. Its characteristic temperatures were slight higher than in as-cast alloy. Moreover, the extruded NiTi alloy showed 100 % of the shape recovery.
- 21 April 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 687, 11-18
The Structure and Properties Formation of the NiTi Shape Memory Rods after Hot Rotary Forging
Shape memory effects, the course and characteristic temperatures of phase transitions and mechanical properties and surface properties of NiTi alloys strongly depend on the chemical composition, the production process used and the plastic working and thermomechanical treatment as well as surface treatment. The test alloy was obtained by vacuum metallurgy by melting the components in a graphite crucible and casting into a graphite ingot mould. In order to obtain the rods in the process of hot plastic working, hot forging was applied using a smith hammer and rotary hot forging on a swaging machine. The resulting rods were subjected to an appropriate heat treatment and thermo mechanical treatment to obtain, at room temperature, a parent phase structure B2.The paper presents the results of the research of NiTi rods after hot rotary forging. The phase composition of the samples of the tested alloy after different heat treatments were determined by X-ray powder diffraction technique. It was found that at room temperature, depending upon the processing the samples had a structure parent phase with a small amount of martensite. The courses of phase transitions and the changes of the temperature characteristic were determined on the basis of the recorded DSC curves. It was found that the test rate after aging in the temperature range of 400-500 °C transitions take place involving the rhombohedral R phase. The temperature ranges of shape recovery of samples after various heat treatments were determined by recording the recovery of the shape during heating, in tests performed according to the standard ASTM 2082-06.
- 21 April 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 687, 11-18
The Structure and Properties Formation of the NiTi Shape Memory Rods after Hot Rotary Forging
Shape memory effects, the course and characteristic temperatures of phase transitions and mechanical properties and surface properties of NiTi alloys strongly depend on the chemical composition, the production process used and the plastic working and thermomechanical treatment as well as surface treatment. The test alloy was obtained by vacuum metallurgy by melting the components in a graphite crucible and casting into a graphite ingot mould. In order to obtain the rods in the process of hot plastic working, hot forging was applied using a smith hammer and rotary hot forging on a swaging machine. The resulting rods were subjected to an appropriate heat treatment and thermo mechanical treatment to obtain, at room temperature, a parent phase structure B2.The paper presents the results of the research of NiTi rods after hot rotary forging. The phase composition of the samples of the tested alloy after different heat treatments were determined by X-ray powder diffraction technique. It was found that at room temperature, depending upon the processing the samples had a structure parent phase with a small amount of martensite. The courses of phase transitions and the changes of the temperature characteristic were determined on the basis of the recorded DSC curves. It was found that the test rate after aging in the temperature range of 400-500 °C transitions take place involving the rhombohedral R phase. The temperature ranges of shape recovery of samples after various heat treatments were determined by recording the recovery of the shape during heating, in tests performed according to the standard ASTM 2082-06.