Miroslav Špano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Miroslav Špano has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Jaromír Říha
Brno University of Technology
4 shared publications Antje Bornschein
KD Ingenieur-Consult GmbH, Dept. Fachbereich Wasserbau , Dresden , Germany
2 shared publications- Bohuslav Rittich
Faculty of Chemistry, Brno University of Technology, Brno, Czech Republic
2 shared publications Dagmar Šrůtková
Academy of Science of the Czech Republic, v.v.i.
2 shared publicationsReinhard Pohl
Institut für Wasserbau und Technische Hydromechanik, Fakultät Bauingenieurwesen , Technische Universität Dresden , Dresden , Germany
2 shared publicationsVladimír Dráb
Dairy Research Institute
2 shared publications
Latest Publications
- Open Access
- 1 June 2022
- Published by Walter de Gruyter GmbH in Slovak Journal of Civil Engineering
- Vol. 30 (2) , 12-21
Wave Run-Ups and Overtopping Affected by Oblique Wave Approaches and Currents
To quantify the effect of a current on the height of a wave’s run-up and overtopping combined with an oblique wave approach, the “FlowDike” hydraulic research project was carried out. Tests were performed on two dike slopes of 1:3 and 1:6. Waves were generated across (perpendicular to) the physical model and also inclined in-plane to the stream axis. Oblique waves were generated both towards and along the flow’s direction. The effect of the current and of the wave direction on the height of the wave run-up and amount of the wave overtopping was expressed by means of a combined correction factor for the wave’s inclination and flow velocity. The results of the research confirmed that the flow velocity had only a small effect.
- 1 June 2022
- Published by Walter de Gruyter GmbH in Slovak Journal of Civil Engineering
- Vol. 30 (2) , 12-21
Open AccessWave Run-Ups and Overtopping Affected by Oblique Wave Approaches and Currents
To quantify the effect of a current on the height of a wave’s run-up and overtopping combined with an oblique wave approach, the “FlowDike” hydraulic research project was carried out. Tests were performed on two dike slopes of 1:3 and 1:6. Waves were generated across (perpendicular to) the physical model and also inclined in-plane to the stream axis. Oblique waves were generated both towards and along the flow’s direction. The effect of the current and of the wave direction on the height of the wave run-up and amount of the wave overtopping was expressed by means of a combined correction factor for the wave’s inclination and flow velocity. The results of the research confirmed that the flow velocity had only a small effect.
- Open Access
Bacterial Diversity in the Asphalt Concrete Lining of the Upper Water Reservoir of a Pumped-Storage Scheme
Asphalt concrete linings (ACLs) are frequently used in pumped-storage hydropower schemes with frequently oscillating reservoir water levels. ACLs can be damaged during operation, which shortens their service life. One type of damage is the formation of blisters. In this study, the bacterial diversity in damaged and undamaged portions of the ACL of an upper water reservoir was evaluated. Matrix-Assisted Laser Desorption/Ionization–Time of Flight Mass Spectrometry (MALDI-TOF MS) was employed for the identification of the bacterial strains. No bacteria were detected growing inside the undamaged dense layer. Low bacterial diversity (2 and 4 morphotypes) was found in the upper part that has no contact with the reservoir water and in the lowest part that is permanently under water, respectively. More complex bacterial diversity (16 morphotypes covered by 2 different genera and 4 species) was found on the mastic coating of the ACL, which was alternately under and above the water. Very complex bacterial compositions (53 morphotypes covered by at least 13 different species from 6 genera) were found in samples taken from open blisters. Bacterial genera that are known to utilize asphalt products as a source of nutrition were found in the open blisters. The results reflect the importance of bacterial diversity in blisters and their possible role in ACL degradation.
Open AccessBacterial Diversity in the Asphalt Concrete Lining of the Upper Water Reservoir of a Pumped-Storage Scheme
Asphalt concrete linings (ACLs) are frequently used in pumped-storage hydropower schemes with frequently oscillating reservoir water levels. ACLs can be damaged during operation, which shortens their service life. One type of damage is the formation of blisters. In this study, the bacterial diversity in damaged and undamaged portions of the ACL of an upper water reservoir was evaluated. Matrix-Assisted Laser Desorption/Ionization–Time of Flight Mass Spectrometry (MALDI-TOF MS) was employed for the identification of the bacterial strains. No bacteria were detected growing inside the undamaged dense layer. Low bacterial diversity (2 and 4 morphotypes) was found in the upper part that has no contact with the reservoir water and in the lowest part that is permanently under water, respectively. More complex bacterial diversity (16 morphotypes covered by 2 different genera and 4 species) was found on the mastic coating of the ACL, which was alternately under and above the water. Very complex bacterial compositions (53 morphotypes covered by at least 13 different species from 6 genera) were found in samples taken from open blisters. Bacterial genera that are known to utilize asphalt products as a source of nutrition were found in the open blisters. The results reflect the importance of bacterial diversity in blisters and their possible role in ACL degradation.
- Open Access
- 1 January 2016
- Published by Airiti Press, Inc. in International Journal of Pavement Research and Technology
- Vol. 9 (1) , 73-81
Investigation on the temperature of the asphalt-concrete facing of embankment dams
Asphalt concrete is a traditional material used for the constructions of upstream sealing of reservoir dams, particularly in upper reservoirs of pumped storage hydroelectric plants. The asphalt layer is often exposed to significant fluctuations of temperature caused, for example, by heating the facing from the sun and by its subsequent rapid cooling by water during reservoir periodical filling. To better understand the physical phenomena and behaviour of the facing in terms of vapour diffusion, the state of stress, etc., it is necessary to know temperature phenomena in the asphalt facing. This paper describes the measurement of temperature in the asphalt facing of the Dlouhe Strane pumped storage hydroelectric plant and its evaluation using 1D numerical model of heat flow in the asphalt concrete facing. Numerical simulation for selected load scenarios enabled the temperature phenomena that take place in the construction of the asphalt-concrete facing to be quantified. The analysis shows that during insolation, the asphalt facing is exposed to the significant temperature rise on its surface and also over its whole thickness. Similarly during frost weather the facing becomes frozen in its entire thickness. During the day cycle the temperature in the asphalt layers changes significantly. However, the temperature in the underlying rockfill dam body becomes steady approximately at the depth of 1.0m
- 1 January 2016
- Published by Airiti Press, Inc. in International Journal of Pavement Research and Technology
- Vol. 9 (1) , 73-81
Open AccessInvestigation on the temperature of the asphalt-concrete facing of embankment dams
Asphalt concrete is a traditional material used for the constructions of upstream sealing of reservoir dams, particularly in upper reservoirs of pumped storage hydroelectric plants. The asphalt layer is often exposed to significant fluctuations of temperature caused, for example, by heating the facing from the sun and by its subsequent rapid cooling by water during reservoir periodical filling. To better understand the physical phenomena and behaviour of the facing in terms of vapour diffusion, the state of stress, etc., it is necessary to know temperature phenomena in the asphalt facing. This paper describes the measurement of temperature in the asphalt facing of the Dlouhe Strane pumped storage hydroelectric plant and its evaluation using 1D numerical model of heat flow in the asphalt concrete facing. Numerical simulation for selected load scenarios enabled the temperature phenomena that take place in the construction of the asphalt-concrete facing to be quantified. The analysis shows that during insolation, the asphalt facing is exposed to the significant temperature rise on its surface and also over its whole thickness. Similarly during frost weather the facing becomes frozen in its entire thickness. During the day cycle the temperature in the asphalt layers changes significantly. However, the temperature in the underlying rockfill dam body becomes steady approximately at the depth of 1.0m
- 28 July 2015
- Published by Springer Nature in European Food Research and Technology
- Vol. 241 (6) , 861-869
Selection of potential probiotic Lactobacillus strains of human origin for use in dairy industry
- 28 July 2015
- Published by Springer Nature in European Food Research and Technology
- Vol. 241 (6) , 861-869
Selection of potential probiotic Lactobacillus strains of human origin for use in dairy industry
- Open Access
- 1 September 2012
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 60 (3) , 174-184
The Influence of Current on the Height of Wind Wave Run-Up: A comparison of experimental results with the Czech National Standard
The Influence of Current on the Height of Wind Wave Run-Up: A comparison of experimental results with the Czech National Standard: One of the basic questions related to the safety of dikes and river levees is the size of the freeboard. One of the important parameters for freeboard design is the height of waves and wave run-up on levee slopes. Routine and standardised calculations of wave run-up deal with the freeboards of dams where wind waves originate on the still water of the reservoir. In the case of running water in streams (thereinafter only "currents") the effect of wave and current interaction on wave run-up is usually not taken into account due to the lack of reliable knowledge regarding the phenomenon. In the Czech Republic this question is topical in the case of large rivers such as the Elbe, the Vltava and the Morava. Within the framework of the projects Hydralab III and NAZV QI 92A139, hydraulic research and further analysis focused on wave run-up as a result of the combination of current and wind wave parameters were performed. The laboratory research was carried out in a hydraulic flume with a wavemaker on the right bank and a levee with a slope of 1:3 installed on the left bank opposite the wavemaker. Waves were generated both perpendicular and oblique to the levee axis; the angle of oblique wave attack varied within the range of ± 30°. The aim of this paper is to compare the results of the mentioned research with recommendations mentioned in the Czech National Standard CSN 75 0255Calculation of wave effects on water structuresand to quantify the effect of current on the wave run-up height.
- 1 September 2012
- Published by Walter de Gruyter GmbH in Journal of Hydrology and Hydromechanics
- Vol. 60 (3) , 174-184
Open AccessThe Influence of Current on the Height of Wind Wave Run-Up: A comparison of experimental results with the Czech National Standard
The Influence of Current on the Height of Wind Wave Run-Up: A comparison of experimental results with the Czech National Standard: One of the basic questions related to the safety of dikes and river levees is the size of the freeboard. One of the important parameters for freeboard design is the height of waves and wave run-up on levee slopes. Routine and standardised calculations of wave run-up deal with the freeboards of dams where wind waves originate on the still water of the reservoir. In the case of running water in streams (thereinafter only "currents") the effect of wave and current interaction on wave run-up is usually not taken into account due to the lack of reliable knowledge regarding the phenomenon. In the Czech Republic this question is topical in the case of large rivers such as the Elbe, the Vltava and the Morava. Within the framework of the projects Hydralab III and NAZV QI 92A139, hydraulic research and further analysis focused on wave run-up as a result of the combination of current and wind wave parameters were performed. The laboratory research was carried out in a hydraulic flume with a wavemaker on the right bank and a levee with a slope of 1:3 installed on the left bank opposite the wavemaker. Waves were generated both perpendicular and oblique to the levee axis; the angle of oblique wave attack varied within the range of ± 30°. The aim of this paper is to compare the results of the mentioned research with recommendations mentioned in the Czech National Standard CSN 75 0255Calculation of wave effects on water structuresand to quantify the effect of current on the wave run-up height.
- 1 October 2011
- Published by Elsevier in Journal of Microbiological Methods
- Vol. 87 (1) , 10-16
Efficiency of PCR-based methods in discriminating Bifidobacterium longum ssp. longum and Bifidobacterium longum ssp. infantis strains of human origin
- 1 October 2011
- Published by Elsevier in Journal of Microbiological Methods
- Vol. 87 (1) , 10-16
Efficiency of PCR-based methods in discriminating Bifidobacterium longum ssp. longum and Bifidobacterium longum ssp. infantis strains of human origin
- Open Access
- 2 February 2011
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- Vol. 1 (32)
ON THE EFFECT OF CURRENT ON WAVE RUN-UP AND WAVE OVERTOPPING
Intention of the project FlowDike-D is to quantify the impacts of current and wind on wave run-up and wave overtopping and to consider these processes in existing design formulae for estuarine, river and sea dikes. Physical model tests were carried out in the shallow water basin at DHI (Hørsholm/Denmark) for two different dike geometries (1:3 and 1:6 sloped dike). The paper introduces the model setup and test programme followed by a short description of the applied instrumentation. The test results for wave run-up and wave overtopping with oblique and non-oblique wave attack, but without current, correspond well with existing formulae from the EurOtop-Manual (2007). The influence of current parallel to the dike combined with different angles of wave attack on wave overtopping and wave run-up has been quantified. A distinction was made between wave attack with and against the current.
- 2 February 2011
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- Vol. 1 (32)
Open AccessON THE EFFECT OF CURRENT ON WAVE RUN-UP AND WAVE OVERTOPPING
Intention of the project FlowDike-D is to quantify the impacts of current and wind on wave run-up and wave overtopping and to consider these processes in existing design formulae for estuarine, river and sea dikes. Physical model tests were carried out in the shallow water basin at DHI (Hørsholm/Denmark) for two different dike geometries (1:3 and 1:6 sloped dike). The paper introduces the model setup and test programme followed by a short description of the applied instrumentation. The test results for wave run-up and wave overtopping with oblique and non-oblique wave attack, but without current, correspond well with existing formulae from the EurOtop-Manual (2007). The influence of current parallel to the dike combined with different angles of wave attack on wave overtopping and wave run-up has been quantified. A distinction was made between wave attack with and against the current.
- 10 December 2009
- Published by Taylor & Francis
- p. 103-106
Evaluation of viscous models for simulation of flow over round-shaped weirs
- 10 December 2009
- Published by Taylor & Francis
- p. 103-106
Evaluation of viscous models for simulation of flow over round-shaped weirs
- 1 January 2008
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1048 (1) , 806-809
Application of a 2D Turbulence Model for Estimation of the Discharge Coefficient on Round‐shaped Weirs
The Czech Republic was affected by extreme floods at the end of 20th and at the beginning of 21 st centuries. As a response to these events and according to the worldwide trend a new law was adopted. The law requires safety management of 10 000‐year flood passage. Many dams in the Czech Rep. (especially the older ones) no longer comply with this requirement. Therefore, significant upgrades of their emergency spillways have to be proposed. Round‐shaped weirs are often used for this purpose. They are easy to build, which is their main advantage. Round‐shaped weirs were used for example in the reconstruction and capacity enhancement of the emergency spillway on the Bystřička dam or the Šance dam. One of the most important parameters of each spillway is its capacity. The capacity is directly influenced by the weir shape, which is represented by the discharge coefficient. A 2D standard k‐ε turbulence model of incompressible open channel flow was used for estimation of the discharge coefficient of a round‐shaped weir. Water levels were traced using the volume of fluid method (VOF). Numerical simulations were performed using commercial software ANSYS‐Flotran (finite element method) and ANSYS‐Fluent (finite volume method). Discharge coefficients were computed from the weir equation. All results from the simulations were further compared with the results from hydraulic research. Also, a comparison of pressures along the weir surface was made.
- 1 January 2008
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1048 (1) , 806-809
Application of a 2D Turbulence Model for Estimation of the Discharge Coefficient on Round‐shaped Weirs
The Czech Republic was affected by extreme floods at the end of 20th and at the beginning of 21 st centuries. As a response to these events and according to the worldwide trend a new law was adopted. The law requires safety management of 10 000‐year flood passage. Many dams in the Czech Rep. (especially the older ones) no longer comply with this requirement. Therefore, significant upgrades of their emergency spillways have to be proposed. Round‐shaped weirs are often used for this purpose. They are easy to build, which is their main advantage. Round‐shaped weirs were used for example in the reconstruction and capacity enhancement of the emergency spillway on the Bystřička dam or the Šance dam. One of the most important parameters of each spillway is its capacity. The capacity is directly influenced by the weir shape, which is represented by the discharge coefficient. A 2D standard k‐ε turbulence model of incompressible open channel flow was used for estimation of the discharge coefficient of a round‐shaped weir. Water levels were traced using the volume of fluid method (VOF). Numerical simulations were performed using commercial software ANSYS‐Flotran (finite element method) and ANSYS‐Fluent (finite volume method). Discharge coefficients were computed from the weir equation. All results from the simulations were further compared with the results from hydraulic research. Also, a comparison of pressures along the weir surface was made.