DZDong Zhou

Dong Zhou

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dong Zhou has a total of 216 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nanofluid wetting of Cu enables thin lithium negative electrodes for high-energy and long-cycling lithium metal batteries

    by Wei Wu, Qilong Wu, Wenting Liu, De Ning, Ming Chen, Jie Zhang, Fengping Zhang, Xuhao Wang, Dong Zhou, Man Wang, et al.

    Exploiting thin Li foils ≤ 20 μm is required for high-energy-density and long-cycling-lifespan battery, but is severely hindered by the poor processability of Li, as well as its inhomogeneous plating behaviors and resulting low Coulombic efficiency. Herein, an approach balancing Li supply and consumption is fulfilled by designing thin molten-salt-derived, nanocomposite Li@LiX metal negative electrodes. Benefitting from the formation of nanofluid due to the spontaneous reaction of inorganic nanoparticles in molten Li, the bonding states at both Li surface and Li|Cu interface are effectively regulated, displaying an enhanced wetting behaviour of Li on Cu. This approach enables the fabrication of an 800-nm-thick Li-based negative electrode foil as well as the formation of an inorganic-rich interphase upon cycling, which suppresses Li consumption by reducing corrosion susceptibility. As a result, practical pouch cells composed of 10-μm-thick Li@lithium bis(fluorosulfonyl)imide (LiFSI) and LiFePO 4 offer stable cycling over 250 cycles, while those composed of 20-μm-thick Li@LiFSI and LiNi 0.92 Co 0.03 Mn 0.05 O 2 with an areal capacity of 4.6 mAh cm −2 achieve 100 cycles, yielding specific energy of 498 Wh kg −1 and energy density of 1,142 Wh L −1 , indicating that this design strategy is applicable to lithium metal batteries.

  • Regulating high-sodium P2 layered oxides through rational lattice modulation for fast kinetics and superior structural stability

    by Zeya Hu, Xingxing Yin, Jiajun Yu, Hairong Li, Mengyue Li, Kaili Li, Xuan He, Xiaokang Ju, Tianyu Zhu, Qidi Wang, et al.

  • Open Access

    Atomic and Molecular Structure Regulated In Situ Cross-Linked Polyurethane Gel Electrolyte for High-Performance Lithium Metal Batteries

    by Jialun Ni, Yong Zeng, De Ning, Xuan He, Xiaokang Ju, Xueling Liu, Rui Gao, Yingchun Xu, Ruijie Du, Dong Zhou, et al.

    The incompatibility of conventional electrolytes with high-voltage cathodes and lithium metal anodes limits the performance of lithium metal batteries (LMBs). Here, an in situ cross-linked polyurethane gel electrolyte (G-P3 AR) is designed through atomic and molecular structure regulation. The polyester segments widen the highest occupied molecular orbital–lowest unoccupied molecular orbital gap, extending the electrochemical stability window to 4.97 V for compatibility with NCM811 cathodes. Polyether segments exhibit a lower Li + binding energy, reducing the desolvation barrier and enhancing anode stability. At the atomic level, sp 2 -hybridized boron in the chain extender immobilizes anions (TFSI − and DFOB − ) through Lewis acid–base interactions, raising the Li + transference number to 0.78 and enabling exceptional rate capability (157.7 mAh g −1 at 2 C in the Li||NCM811 cell). Hydrogen bonding between the polymer and solvent restructures the solvation sheath, promoting inorganic-rich interphases. The Li|G-P3 AR|NCM811 cell retains 81.7% capacity after 500 cycles at 0.5 C charge/1 C discharge, demonstrating a rational electrolyte design strategy for high-performance LMBs.


  • Open Access

    Origin of crack propagation in lithium cobalt oxide positive electrode for lithium-ion batteries

    by Wenguang Zhao, Zijian Li, Mingyang Li, Hengyu Ren, Cong Lin, Haocong Yi, Shengyu Wu, Xiaohu Wang, Jun Wang, Bin Fei, et al.

    Although the anionic activity in layered oxide positive electrodes is partially understood, the mechanism by which it induces internal crack propagation under high-voltage conditions remains unclear, severely limiting stable cycle life and available capacity. In this study, the mechanism underlying internal crack propagation is elucidated in LiCoO2 under harsh float-charge conditions at 60 °C and a potential of 4.6 V vs. Li+/Li. We reveal that sequential phase transitions from O3 to O1 and then to a cation-mixed phase during deep Li+ extraction generate significant lattice-mismatch stresses that initiate internal cracks. Crucially, the accompanying anionic activity drives the migration of the oxidized lattice On− (0 < n < 2) towards these cracks, where it even accumulates as molecular O2 that can be released upon crack propagation to the surface. It is identified that the sustained O1tocation-mixed phase transition and the bulk lattice On− migration synergistically drive the interior crack propagation, ultimately leading to LiCoO2 disintegration and electrochemical degradation. This work not only deepens our understanding of the anionic activity in layered positive electrodes but also provides mechanistic insights for the future design of stable LiCoO2 positive electrodes.


  • Roles of Slab-Gliding-Induced Surface Nano-Steps in High-Voltage Instability of LiCoO 2

    by Wenguang Zhao, Zijian Li, Tongsheng Deng, Hengyu Ren, Haocong Yi, Xiaohu Wang, Feng Jin, Cong Lin, Zhihao Shen, Shiming Chen, et al.

    Rapid capacity decay caused by lattice oxygen (lattice-O) loss under high-voltage operation remains a critical challenge for layered LiCoO2 (LCO) cathodes. Recently, various surface modification strategies have been explored to suppress lattice-O loss, yet the underlying mechanisms remain controversial. Herein, we identify slab-gliding-induced surface nanosteps on LCO and elucidate their role in driving lattice-O loss. These nanosteps (10-20 nm per step) are induced by local Co-O slab gliding during phase transitions upon deep delithiation, thereby exposing numerous active lattice On- (0 < n < 2) sites on the (003) and (104) planes, where oxygen vacancies (OVs) can form with significantly reduced formation energies. Consequently, this accelerates lattice-O loss and promotes the formation of a surface Li+-blocking layer, ultimately causing a rapid capacity decay. We further demonstrate that even if a rock-salt (RS) phase forms electrochemically in situ (e-RS) on the LCO surface, it fails to suppress the lattice-O loss due to the emergence of surface nanosteps. In contrast, a prefabricated RS layer (p-RS) with enhanced mechanical robustness effectively inhibits the formation of such nanosteps, thereby intrinsically suppressing lattice-O loss during cycling. This work identifies slab-gliding-induced surface nanosteps as a key structural trigger for lattice-O loss and demonstrates that prefabricated RS coatings offer an effective route to stabilize high-voltage LCO cathodes.


  • Open Access

    Interfacial engineering enables stable cycling of high voltage Li-rich cathodes in PEO-based all-solid-state batteries

    by Yuanyuan Du, Zhenyao Wei, Qingwen Gu, Qiao Zhang, Lirong Liao, Runji Chen, Junhao Li, Wenguang Zhao, Zhaoping Liu, Liangtao Yang, et al.

    Poly(ethylene oxide)-based solid polymer electrolytes (PEO-SPEs) are regarded as promising alternatives to liquid electrolyte in batteries due to their improved safety and good compatibility with lithium-metal anode. However, the decomposition of PEO matrix at high voltage that leads to capacity degradation, hindering its further deployment in high-voltage all-solid-state lithium-metal batteries (ASSLMBs). Herein, we studied the failure mechanism of PEO-SPEs with high-capacity Li-rich layered cathode and reported a strategy of using an Al2O3 coating to improve electrochemical performance. The anion redox of Li1.2Ni0.13Co0.13Mn0.54O2 (LR114) generates reactive oxygen species, causing the terminal hydrogen of PEO to dissociate into H+, which combines with TFSI– to form HTFSI. HTFSI initiates the further autocatalytic decomposition of PEO, which induces the dissolution of transition metals and formation of the spinel-like phase on the surface of LR114. By integrating Al2O3 protective layer on cathodes, it adsorbs the TFSI–/FSI– anions preferentially, leading to the formation of a LiF-rich cathode-electrolyte interphase (CEI), which in turn inhibits the decomposition of PEO. The obtained Li-In|PEO|Al2O3@LR114 ASSLMBs exhibit better cycling performance with a capacity retention of 93.5% after 100 cycles at 0.2 C. This study demonstrates the potential of interfacial engineering to control the chemical composition of electrode-electrolyte interphase in high-voltage ASSLMBs.


  • Open Access

    Author Correction: Substitution and electrochemistry in layered oxide cathode materials for sodium-ion batteries

    by Liangtao Yang, Xingxing Yin, Jun Wang, Yanan Sun, Yongchun Li, Zhenggang Zhang, Zhongqing Liu, Si-Min Huang, Philipp Adelhelm, Dong Zhou


  • Top Cited Papers

    Substitution and electrochemistry in layered oxide cathode materials for sodium-ion batteries

    by Liangtao Yang, Xingxing Yin, Jun Wang, Yanan Sun, Yongchun Li, Zhenggang Zhang, Zhongqing Liu, Si-Min Huang, Philipp Adelhelm, Dong Zhou

    Substitution is a vital strategy for developing high-performance sodium layered oxides (SLOs), which demonstrates great potential for making sodium-ion batteries a viable alternative to lithium-ion batteries. Numerous studies have been conducted on substituted SLOs; however, each substitute exhibits varied effects on the structure and electrochemical performance of the SLOs, and no clear design principles have been established. Clarifying the relationship among substitution, structure and performance is therefore important to enable a rational design strategy for high-performance SLOs. In this Review, the up-to-date substitution guidelines and the current understanding of how substitution affects the structure and electrochemistry in SLOs are discussed, and the site preference and characteristic redox features of different types of substitutes are outlined. The inherent challenges and opportunities for the innovation of better-performing SLOs are summarized, paving the way for accelerating the commercialization of SLO-based sodium-ion batteries and the realization of their applications ranging from electric vehicles to grid energy storage systems.


  • Crystal Modulation of Mn‐Based Layered Oxide toward Long‐Enduring Anionic Redox with Fast Kinetics for Sodium‐Ion Batteries

    by Gaoyuan Zhang, XingXing Yin, De Ning, Yan Chai, Ruijie Du, Dingbang Hao, Chunling Wang, Xueling Liu, Rui Gao, Jun Wang, et al.

    Mn‐based layered oxide cathodes for sodium‐ion batteries with anionic redox reactions hold great potential for energy storage applications due to their ultra‐high capacity and cost effectiveness. However, achieving high capacity requires overcoming challenges such as oxygen‐redox failure, sluggish kinetics, and structural degradation. Herein, we employ an innovative crystal modulation strategy, using Mn‐based Na 0.72 Li 0.24 Mn 0.76 O 2 as a representative cathode material, which shows that the highly exposed {010} active facets enable an enhanced rate capability (119.6 mAh g −1 at 10 C) with fast kinetics. Meanwhile, the reinforced Mn−O bond inhibits excessive oxidation of lattice oxygen and O−O cohesion loss, stabilizing and maintaining a long‐enduring reversible oxygen‐redox activity (100 % high capacity retention after 100 cycles at 0.5 C and 84.28 % retention after 300 cycles at 5 C). Time‐resolved operando two‐dimensional X‐ray diffraction reveals the robust structural stability, zero‐strain behavior, and suppressed phase transition with ultra‐low volume variation during cycling at different rates (0.1 C: 1.75 %, 1 C: 0.31 %, 5 C: 0.04 %). Additionally, the full cell coupled with hard carbon achieves a high energy density of approximately 211 Wh kg −1 with superior performance. This work highlights the significance of crystal modulation and presents a universal approach in developing Mn‐based oxide cathodes with stable anionic redox for high‐performance sodium‐ion batteries.