Jinbo Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jinbo Zhang has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Liao Yang
Fudan Univ, Dept Opt Sci & Engn, Shanghai Engn Res Ctr Ultraprecis Opt Mfg, Shanghai 200433, Peoples R China
5 shared publicationsRong-Jun Zhang
Fudan Univ, Dept Opt Sci & Engn, Shanghai Engn Res Ctr Ultraprecis Opt Mfg, Shanghai 200433, Peoples R China
5 shared publications- Yu-Xiang Zheng
Fudan University
4 shared publications Liang-Yao Chen
Fudan Univ, Dept Opt Sci & Engn, Shanghai Engn Res Ctr Ultraprecis Opt Mfg, Shanghai 200433, Peoples R China
3 shared publications- Lin Wang
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao, China
3 shared publications Shang-Dong Yang
Fudan Univ, Dept Opt Sci & Engn, Shanghai Engn Res Ctr Ultraprecis Opt Mfg, Shanghai 200433, Peoples R China
3 shared publications
Latest Publications
- 9 May 2023
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 62 (25) , e202303315
Synthesis of Sequence‐specific Poly(ester‐carbonate) Copolymers via Chemoselective Terpolymerization Controlled by the Stoichiometric Ratio of Phosphazene/Triethylborane
Chemoselective terpolymerization can produce polymer materials with diverse compositions and sequential structures, and thus have attracted considerable attention in the field of polymer synthesis. However, the intrinsic complexity of three‐component system also brings great chanllenge, in regard to the reactivity and selectivity of different monomers. Herein, we report the terpolymerization of CO2/epoxide/anhydride by a binary organocatalytic C3N3‐Py‐P3/TEB (triethylborane) system. Both the activity and chemoselectivity were highly dependent upon the molar ratio of C3N3‐Py‐P3 to TEB, and sequence‐controlled poly(ester‐carbonate) copolymers were readily synthesized through one‐pot/one‐step methodology by tuning the stoichiometric ratio of phosphazene/TEB. In particular, C3N3‐Py‐P3/TEB with a molar ratio of 1/0.5 exhibited an unprecedentedly high chemoselectivity for ring‐opening alternating copolymerization (ROAC) of cyclohexene oxide (CHO) and phthalic anhydride (PA) first and then ROAC of CO2/CHO. Thus, well‐defined triblock polycarbonate‐b‐polyester‐b‐polycarbonate copolymers can be produced from the mixture of CO2, CHO and PA using a bifunctional initiator. With C3N3‐Py‐P3/TEB=1/1, tapered copolymers were obtained, while random copolymers with high content of polycarbonate (PC) were synthesized with further increasing the amount of TEB. The mechanism of the unexpected chemoselectivity was further investigated by DFT calculations.
- 9 May 2023
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 62 (25) , e202303315
Synthesis of Sequence‐specific Poly(ester‐carbonate) Copolymers via Chemoselective Terpolymerization Controlled by the Stoichiometric Ratio of Phosphazene/Triethylborane
Chemoselective terpolymerization can produce polymer materials with diverse compositions and sequential structures, and thus have attracted considerable attention in the field of polymer synthesis. However, the intrinsic complexity of three‐component system also brings great chanllenge, in regard to the reactivity and selectivity of different monomers. Herein, we report the terpolymerization of CO2/epoxide/anhydride by a binary organocatalytic C3N3‐Py‐P3/TEB (triethylborane) system. Both the activity and chemoselectivity were highly dependent upon the molar ratio of C3N3‐Py‐P3 to TEB, and sequence‐controlled poly(ester‐carbonate) copolymers were readily synthesized through one‐pot/one‐step methodology by tuning the stoichiometric ratio of phosphazene/TEB. In particular, C3N3‐Py‐P3/TEB with a molar ratio of 1/0.5 exhibited an unprecedentedly high chemoselectivity for ring‐opening alternating copolymerization (ROAC) of cyclohexene oxide (CHO) and phthalic anhydride (PA) first and then ROAC of CO2/CHO. Thus, well‐defined triblock polycarbonate‐b‐polyester‐b‐polycarbonate copolymers can be produced from the mixture of CO2, CHO and PA using a bifunctional initiator. With C3N3‐Py‐P3/TEB=1/1, tapered copolymers were obtained, while random copolymers with high content of polycarbonate (PC) were synthesized with further increasing the amount of TEB. The mechanism of the unexpected chemoselectivity was further investigated by DFT calculations.
- Open Access
- 16 December 2020
- Published by Atlantis Press SARL
- p. 124-128
Teaching Reform and Practice of Medical Microbiology Course Based on Innovative and Entrepreneurial Talent Training Mode
- 16 December 2020
- Published by Atlantis Press SARL
- p. 124-128
Open AccessTeaching Reform and Practice of Medical Microbiology Course Based on Innovative and Entrepreneurial Talent Training Mode
- 25 February 2020
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 32 (21) , 215401
Pressure induced band gap narrowing and phase transitions in Dy 2 Ti 2 O 7
An isostructural phase transition and a cubic to tetragonal phase transition in spin-frustrated pyrochlore Dy 2 Ti 2 O 7 (DTO) at 35 GPa and 46 GPa, respectively, were detected by x-ray diffraction (XRD) and Raman spectroscopy studies at room temperature under high pressure. The band gap of DTO gradually increased with the increasing pressure up to 20 GPa, after which it narrowed significantly around 35 GPa, and further manifested with a slight discontinuity around 46 GPa. Below 35 GPa, the evolution of band gap with pressure maintained a close relationship with the Ti–O bond length and the distortion of TiO 6 octahedron. The remarkable narrowing of the band gap around 35 GPa implied the changes of the band structure and confirmed the isostructural phase transition. These findings provide an in-depth understanding of the evolution of the structure and the band gap of DTO under high pressure.
- 25 February 2020
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 32 (21) , 215401
Pressure induced band gap narrowing and phase transitions in Dy 2 Ti 2 O 7
An isostructural phase transition and a cubic to tetragonal phase transition in spin-frustrated pyrochlore Dy 2 Ti 2 O 7 (DTO) at 35 GPa and 46 GPa, respectively, were detected by x-ray diffraction (XRD) and Raman spectroscopy studies at room temperature under high pressure. The band gap of DTO gradually increased with the increasing pressure up to 20 GPa, after which it narrowed significantly around 35 GPa, and further manifested with a slight discontinuity around 46 GPa. Below 35 GPa, the evolution of band gap with pressure maintained a close relationship with the Ti–O bond length and the distortion of TiO 6 octahedron. The remarkable narrowing of the band gap around 35 GPa implied the changes of the band structure and confirmed the isostructural phase transition. These findings provide an in-depth understanding of the evolution of the structure and the band gap of DTO under high pressure.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 56-60
Online Monitoring Device for Partial Discharge in High-Voltage Switchgear Based on Capacitance Coupling Method
There are many problems in traditional manual inspection, such as poor real-time performance, complex operation and large environmental impact on monitoring results when using ultrasonic and ultra high frequency (UHF) inspection methods. In order to realize online monitoring of partial discharge (PD) in high-voltage switchgears, a live display capacitance sensor equipped with high-voltage switchgear is proposed to acquire discharge pulse and monitor the discharge information of switchgear in real time. With the technology of FPGA, the sampling frequency of 50MHz is used to collect one million data points in 10 milliseconds and a half cycle. Hanning window function data processing technology and fast Fourier transform (FFT) technology are used to obtain the high frequency discharge spectrum of the internal ports and insulators of high-voltage switchgear cabinet, thus realizing the online monitoring of PD, and greatly reducing the cost of the monitoring circuit. It is convenient for popularization and application, and meets the online monitoring requirements of PD through practical tests.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 56-60
Online Monitoring Device for Partial Discharge in High-Voltage Switchgear Based on Capacitance Coupling Method
There are many problems in traditional manual inspection, such as poor real-time performance, complex operation and large environmental impact on monitoring results when using ultrasonic and ultra high frequency (UHF) inspection methods. In order to realize online monitoring of partial discharge (PD) in high-voltage switchgears, a live display capacitance sensor equipped with high-voltage switchgear is proposed to acquire discharge pulse and monitor the discharge information of switchgear in real time. With the technology of FPGA, the sampling frequency of 50MHz is used to collect one million data points in 10 milliseconds and a half cycle. Hanning window function data processing technology and fast Fourier transform (FFT) technology are used to obtain the high frequency discharge spectrum of the internal ports and insulators of high-voltage switchgear cabinet, thus realizing the online monitoring of PD, and greatly reducing the cost of the monitoring circuit. It is convenient for popularization and application, and meets the online monitoring requirements of PD through practical tests.
- 1 January 2019
- Published by Elsevier in Applied Surface Science
- Vol. 465, 532-536
Dispersion properties in the visible range of carrier concentration of topologically protected Bi1-xSex films revealed by spectroscopic ellipsometry
- 1 January 2019
- Published by Elsevier in Applied Surface Science
- Vol. 465, 532-536
Dispersion properties in the visible range of carrier concentration of topologically protected Bi1-xSex films revealed by spectroscopic ellipsometry
- Open Access
- 1 September 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (9) , 095012
In situ high-pressure spectroscopic studies using moissanite (4H-SiC) anvils
We examined the Raman scattering and IR absorption spectroscopy of 4H-SiC and its performance as an anvil material for high-pressure UV-visible absorption spectroscopic measurements. The first- and second-order Raman peaks of 4H-SiC and diamond do not coincide. 4H-SiC does not have obvious signals from 2330-5000 cm-1, suggesting that 4H-SiC anvils are beneficial for high-pressure studies of samples whose Raman signals locate in the region of diamond. Above 1800 cm-1, the transmitted signal of 4H-SiC in the IR absorption spectra, measured through 4.6 mm thickness is much higher than that of type IIa diamond. An in situ high-pressure UV-visible absorption spectroscopy study on CdI2 was carried out up to 28.0 GPa using 4H-SiC anvil cells (4H-SAC) with a 400 μm culet and the acquired band gap narrowed with increasing pressure. These results show that 4H-SiC has an excellent performance in high-pressure spectroscopic studies.
- 1 September 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (9) , 095012
Open AccessIn situ high-pressure spectroscopic studies using moissanite (4H-SiC) anvils
We examined the Raman scattering and IR absorption spectroscopy of 4H-SiC and its performance as an anvil material for high-pressure UV-visible absorption spectroscopic measurements. The first- and second-order Raman peaks of 4H-SiC and diamond do not coincide. 4H-SiC does not have obvious signals from 2330-5000 cm-1, suggesting that 4H-SiC anvils are beneficial for high-pressure studies of samples whose Raman signals locate in the region of diamond. Above 1800 cm-1, the transmitted signal of 4H-SiC in the IR absorption spectra, measured through 4.6 mm thickness is much higher than that of type IIa diamond. An in situ high-pressure UV-visible absorption spectroscopy study on CdI2 was carried out up to 28.0 GPa using 4H-SiC anvil cells (4H-SAC) with a 400 μm culet and the acquired band gap narrowed with increasing pressure. These results show that 4H-SiC has an excellent performance in high-pressure spectroscopic studies.
- 10 May 2018
- Published by American Physical Society (APS) in Physical Review B
- Vol. 97 (17) , 174102
Pressure-induced structural and semiconductor-semiconductor transitions inThe effect of pressure on the structural, vibrational, and electronic properties of Mg-doped Cr bearing spinel was studied up to 55 GPa at room-temperature using x-ray diffraction, Raman spectroscopy, electrical transport measurements, and ab initio calculations. We found that the ambient-pressure phase is cubic (spinel-type, ) and underwent a pressure-induced structural transition to a tetragonal phase (space group ) above 28 GPa. The ab initio calculation confirmed this first-order phase transition. The resistivity of the sample decreased at low pressures with the existence of a low-pressure (LP) phase and started to increase with the emergence of a high-pressure (HP) phase. The temperature dependent resistivity experiments at different pressures illustrated the wide band gap semiconducting nature of both the LP and HP phases with different activation energies, suggesting a semiconductor-semiconductor transition at HP. No evidence of chemical decomposition or a semiconductor-metal transition was observed in our studies.- 10 May 2018
- Published by American Physical Society (APS) in Physical Review B
- Vol. 97 (17) , 174102
Pressure-induced structural and semiconductor-semiconductor transitions inThe effect of pressure on the structural, vibrational, and electronic properties of Mg-doped Cr bearing spinel was studied up to 55 GPa at room-temperature using x-ray diffraction, Raman spectroscopy, electrical transport measurements, and ab initio calculations. We found that the ambient-pressure phase is cubic (spinel-type, ) and underwent a pressure-induced structural transition to a tetragonal phase (space group ) above 28 GPa. The ab initio calculation confirmed this first-order phase transition. The resistivity of the sample decreased at low pressures with the existence of a low-pressure (LP) phase and started to increase with the emergence of a high-pressure (HP) phase. The temperature dependent resistivity experiments at different pressures illustrated the wide band gap semiconducting nature of both the LP and HP phases with different activation energies, suggesting a semiconductor-semiconductor transition at HP. No evidence of chemical decomposition or a semiconductor-metal transition was observed in our studies.- 1 November 2017
- Published by Elsevier in Applied Surface Science
- Vol. 421, 899-904
Ellipsometric study on temperature dependent optical properties of topological bismuth film
- 1 November 2017
- Published by Elsevier in Applied Surface Science
- Vol. 421, 899-904
Ellipsometric study on temperature dependent optical properties of topological bismuth film
- 31 May 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (26) , 265304
Optical constants of e-beam evaporated and annealed Nb2O5thin films with varying thickness
Niobium pentoxide (Nb 2 O 5 ) films with different thicknesses were prepared using the electron beam evaporation method and then annealed at temperatures from 300 °C to 800 °C before being characterized by variable-angle spectroscopic ellipsometry, x-ray diffraction, etc. The results showed that the optical constants and microstructures of Nb 2 O 5 films exhibit a strong dependence on the annealing temperature. In the visible light region, the refractive indices show a positive correlation with the annealing temperature from 300 °C to 600 °C, but a negative correlation from 600 °C to 800 °C. The amorphous Nb 2 O 5 film converts into TT- Nb 2 O 5 (pseudo-hexagonal) after annealing at 500–600 °C, and into T-Nb 2 O 5 (orthorhombic) after annealing at 700–800 °C.
- 31 May 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (26) , 265304
Optical constants of e-beam evaporated and annealed Nb2O5thin films with varying thickness
Niobium pentoxide (Nb 2 O 5 ) films with different thicknesses were prepared using the electron beam evaporation method and then annealed at temperatures from 300 °C to 800 °C before being characterized by variable-angle spectroscopic ellipsometry, x-ray diffraction, etc. The results showed that the optical constants and microstructures of Nb 2 O 5 films exhibit a strong dependence on the annealing temperature. In the visible light region, the refractive indices show a positive correlation with the annealing temperature from 300 °C to 600 °C, but a negative correlation from 600 °C to 800 °C. The amorphous Nb 2 O 5 film converts into TT- Nb 2 O 5 (pseudo-hexagonal) after annealing at 500–600 °C, and into T-Nb 2 O 5 (orthorhombic) after annealing at 700–800 °C.
- 5 May 2016
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 120 (19) , 10686-10690
Ellipsometric Study on Size-Dependent Melting Point of Nanometer-Sized Indium Particles
- 5 May 2016
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 120 (19) , 10686-10690
Ellipsometric Study on Size-Dependent Melting Point of Nanometer-Sized Indium Particles