Viktors Gutakovskis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Viktors Gutakovskis has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- A. Avisane
Riga Technical University, Riga, Latvia
1 shared publication - A. Gerina-Ancane
Riga Technical University, Riga, Latvia
1 shared publication - A. Steklejns
Riga Technical University, Riga, Latvia
1 shared publication Ajay Varma Buddaraju
1 shared publicationAnita Avisane
1 shared publicationAntons Steklejns
1 shared publication
Latest Publications
- 9 February 2023
- Published by Riga Technical University
Precision of Stainless Steel Turning Process Depending on Al2O3 Nano-coated Cutting Tool Wear
In the PhD Thesis a method for determining the roughness of a turned surface for hard-to-machine materials has been developed using increased processing parameters, the application of a turning process without cooling emulsion, using new cutting tools, and the cutting process has been investigated. The Thesis presents the study on the chip formation process and the result of cutting tool wear using the tools produced by different manufacturers. A literature review is presented and research directions are defined. The results of material turning of two groups of stainless steel structures are reviewed. Several mathematical models of the turning process have been developed for predicting surface roughness using regression analysis. The influence of material alloying elements on the chip formation process has been studied. The accuracy of the regression prediction models has been evaluated and an experimental model has been tested. Finite element method modelling of the turning process has been represented and the obtained data, which could not be obtained before, with the help of a practical experiment have been obtained.
- 9 February 2023
- Published by Riga Technical University
Precision of Stainless Steel Turning Process Depending on Al2O3 Nano-coated Cutting Tool Wear
In the PhD Thesis a method for determining the roughness of a turned surface for hard-to-machine materials has been developed using increased processing parameters, the application of a turning process without cooling emulsion, using new cutting tools, and the cutting process has been investigated. The Thesis presents the study on the chip formation process and the result of cutting tool wear using the tools produced by different manufacturers. A literature review is presented and research directions are defined. The results of material turning of two groups of stainless steel structures are reviewed. Several mathematical models of the turning process have been developed for predicting surface roughness using regression analysis. The influence of material alloying elements on the chip formation process has been studied. The accuracy of the regression prediction models has been evaluated and an experimental model has been tested. Finite element method modelling of the turning process has been represented and the obtained data, which could not be obtained before, with the help of a practical experiment have been obtained.
- 9 February 2023
- Published by Riga Technical University
Nerūsējošā tērauda apvirpošanas procesa precizitāte atkarībā no Al2O3 nano pārklāta griezējinstrumenta nodiluma
Promocijas darbā izstrādāta apvirpotas virsmas raupjuma noteikšanas metode grūti apstrādājamām materiālam palielinātos apstrādes režīmos virpošanās procesā bez dzesēšanas emulsijas lietošanas, izmantojot jaunus griezējinstrumentus, kā arī ir izpētīts griešanas process, pētot skaidu veidošanos un griezējinstrumenta nodiluma rezultātu, lietojot analoģiskus instrumentus. Veikts literatūras apskats, un definēti pētījumu virzieni. Apskatītas divu nerūsējošo tēraudu struktūru grupu materiālu apvirpošanas rezultāti, izstrādāti vairāki apvirpošanas procesa matemātiskie modeļi virsmas raupjuma prognozēšanai, lietojot regresijas analīzi. Pētīta materiālu leģējošo elementu ietekme uz skaidu veidošanās procesu, izvērtēta regresijas prognozēšanas modeļu precizitāte, kā arī veikta eksperimentālā modeļa atbilstības pārbaude un apvirpošanas procesa galīgo elementu metodes modelēšana, iegūstot datus, ko nebija iespējams noskaidrot ar praktiskā eksperimenta palīdzību.
- 9 February 2023
- Published by Riga Technical University
Nerūsējošā tērauda apvirpošanas procesa precizitāte atkarībā no Al2O3 nano pārklāta griezējinstrumenta nodiluma
Promocijas darbā izstrādāta apvirpotas virsmas raupjuma noteikšanas metode grūti apstrādājamām materiālam palielinātos apstrādes režīmos virpošanās procesā bez dzesēšanas emulsijas lietošanas, izmantojot jaunus griezējinstrumentus, kā arī ir izpētīts griešanas process, pētot skaidu veidošanos un griezējinstrumenta nodiluma rezultātu, lietojot analoģiskus instrumentus. Veikts literatūras apskats, un definēti pētījumu virzieni. Apskatītas divu nerūsējošo tēraudu struktūru grupu materiālu apvirpošanas rezultāti, izstrādāti vairāki apvirpošanas procesa matemātiskie modeļi virsmas raupjuma prognozēšanai, lietojot regresijas analīzi. Pētīta materiālu leģējošo elementu ietekme uz skaidu veidošanās procesu, izvērtēta regresijas prognozēšanas modeļu precizitāte, kā arī veikta eksperimentālā modeļa atbilstības pārbaude un apvirpošanas procesa galīgo elementu metodes modelēšana, iegūstot datus, ko nebija iespējams noskaidrot ar praktiskā eksperimenta palīdzību.
- Open Access
- 1 February 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (1) , 267-273
Usage of Cold Forcing Method for a Gas Turbine Engine of Supersonic Transport
The article discusses the current state of development of supersonic transport, analyses the main limitation of the use of gas turbine engines when flying at high supersonic flight speeds, proposes a method for expanding the range of GTE limitations in these flight modes of the aircraft, using...
- 1 February 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (1) , 267-273
Open AccessUsage of Cold Forcing Method for a Gas Turbine Engine of Supersonic Transport
The article discusses the current state of development of supersonic transport, analyses the main limitation of the use of gas turbine engines when flying at high supersonic flight speeds, proposes a method for expanding the range of GTE limitations in these flight modes of the aircraft, using...
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2803 (1) , 040011
Experimental investigation of the machining process of AISI 304 during dry metal cutting process using modern nanocoated cutting tools
As the wide application of stainless steel is increasing and cutting tool materials and coatings are developing in the world, the research and predictions in the fields of its wear and distribution are becoming more and more topical. Thus, research of processing parameters and factors influencing them is crucial. Stainless steel is steady, and it is a material that is difficult to process. It contains various alloy elements which increase its flexibility and hardness, and when turned make the processing very difficult, since the chip formation process is complicated. In modern automated mass or large series production, the chips obtained using current technology are not accepted. Thus, the research of the chip formation process is crucial. The influence of stainless steel (AISI420 and AISI 304) martensitic and austenitic structures were investigated and analyzed during the turning using the Duratomic nanocoated cutting tools. The Duratomic nanocoated cutting tools in comparison with the other known tools have larger wear resistance in the rough turning in complex with the bigger amount of the removed material. The better results were also achieved in exact processing with higher cutting speed and lower cutting, despite a significant increase in the cutting temperature. The use of Duratomic nanocoated cutting tools well coincides with the so-called clean manufacturing, which means, for example, not using a cutting fluid. For manufacturing such tools the wear-resistant multilayer nanocoatings are deposited by PVD Physical Vapour Deposition) on cemented carbide. Each layer has different composition/properties such as hardness, toughness, etc., and, as a result of such architecture, there are better functional properties in comparison with the well-known coated cutting tolls with a single layer of the same thickness (2-12 µm). In this research, the Duratomic nanocoated cutting tools are examined during dry machining by variation of the machining parameters. The temperature field distribution in the cutting tool, and the chip formation process were examined as well. Since the wear resistance of the cutting tool has a great influence on the roughness of the machined surface, and chip formation process, the influence of the alloy elements was taken into account. The mathematical model of the cutting process is elaborated and analyzed. The better functional properties of the Duratomic nanocoated cutting tools with the appropriate inserts in comparison to other analog cutting inserts by different manufacturers are proven.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2803 (1) , 040011
Open AccessExperimental investigation of the machining process of AISI 304 during dry metal cutting process using modern nanocoated cutting tools
As the wide application of stainless steel is increasing and cutting tool materials and coatings are developing in the world, the research and predictions in the fields of its wear and distribution are becoming more and more topical. Thus, research of processing parameters and factors influencing them is crucial. Stainless steel is steady, and it is a material that is difficult to process. It contains various alloy elements which increase its flexibility and hardness, and when turned make the processing very difficult, since the chip formation process is complicated. In modern automated mass or large series production, the chips obtained using current technology are not accepted. Thus, the research of the chip formation process is crucial. The influence of stainless steel (AISI420 and AISI 304) martensitic and austenitic structures were investigated and analyzed during the turning using the Duratomic nanocoated cutting tools. The Duratomic nanocoated cutting tools in comparison with the other known tools have larger wear resistance in the rough turning in complex with the bigger amount of the removed material. The better results were also achieved in exact processing with higher cutting speed and lower cutting, despite a significant increase in the cutting temperature. The use of Duratomic nanocoated cutting tools well coincides with the so-called clean manufacturing, which means, for example, not using a cutting fluid. For manufacturing such tools the wear-resistant multilayer nanocoatings are deposited by PVD Physical Vapour Deposition) on cemented carbide. Each layer has different composition/properties such as hardness, toughness, etc., and, as a result of such architecture, there are better functional properties in comparison with the well-known coated cutting tolls with a single layer of the same thickness (2-12 µm). In this research, the Duratomic nanocoated cutting tools are examined during dry machining by variation of the machining parameters. The temperature field distribution in the cutting tool, and the chip formation process were examined as well. Since the wear resistance of the cutting tool has a great influence on the roughness of the machined surface, and chip formation process, the influence of the alloy elements was taken into account. The mathematical model of the cutting process is elaborated and analyzed. The better functional properties of the Duratomic nanocoated cutting tools with the appropriate inserts in comparison to other analog cutting inserts by different manufacturers are proven.
- Open Access
- 20 April 2021
- Published by IntechOpen
Performance Assessment of the Thermodynamic Cycle in a Multi-Mode Gas Turbine Engine
This chapter discusses the direction of development of promising multimode aviation gas turbine engines (GTE). It is shown that the development of GTE is on the way to increase the parameters engine workflow: gas temperatures in front of the turbine (T*G) and the degree of pressure increase in the compressor (P*C). It is predicted that the next generation engines will operate with high parameters of the working process, T*G = 2000–2200 K, π*C = 60–80. At this temperature of gases in front of the turbine, the working mixture in the combustion chamber (CC) is stoichiometric, which sharply narrows the range of stable operation of the CC and its efficiency drops sharply in off-design gas turbine engine operation modes. To expand the range of effective and stable work, it is proposed to use an advanced aviation GTE: Adaptive Type Combustion Chamber (ATCC). A scheme of the ATCC and the principles of its regulation in the system of a multi-mode gas turbine engine are presented. The concept of an adaptive approach is given in this article. There are two main directions for improving the characteristics of a promising aviation gas turbine engine. One is a complication of the concepts of aircraft engines and the other one is an increase in the parameters of the working process, the temperature of the gases in front of the turbine (T*G) and the degree of increasing pressure behind the compressor (π*C). It is shown how the principles of adaptation are used in these areas. The application of the adaptation principle in resolving the contradiction of the possibility of obtaining optimal characteristics of a high-temperature combustion chamber (CC) of a gas turbine engine under design (optimal) operating conditions and the impossibility of their implementation when these conditions change in the range of acceptable (non-design) gas turbine operation modes is considered in detail. The use of an adaptive approach in the development of promising gas turbine engines will significantly improve their characteristics and take into account unknown challenges.
- 20 April 2021
- Published by IntechOpen
Open AccessPerformance Assessment of the Thermodynamic Cycle in a Multi-Mode Gas Turbine Engine
This chapter discusses the direction of development of promising multimode aviation gas turbine engines (GTE). It is shown that the development of GTE is on the way to increase the parameters engine workflow: gas temperatures in front of the turbine (T*G) and the degree of pressure increase in the compressor (P*C). It is predicted that the next generation engines will operate with high parameters of the working process, T*G = 2000–2200 K, π*C = 60–80. At this temperature of gases in front of the turbine, the working mixture in the combustion chamber (CC) is stoichiometric, which sharply narrows the range of stable operation of the CC and its efficiency drops sharply in off-design gas turbine engine operation modes. To expand the range of effective and stable work, it is proposed to use an advanced aviation GTE: Adaptive Type Combustion Chamber (ATCC). A scheme of the ATCC and the principles of its regulation in the system of a multi-mode gas turbine engine are presented. The concept of an adaptive approach is given in this article. There are two main directions for improving the characteristics of a promising aviation gas turbine engine. One is a complication of the concepts of aircraft engines and the other one is an increase in the parameters of the working process, the temperature of the gases in front of the turbine (T*G) and the degree of increasing pressure behind the compressor (π*C). It is shown how the principles of adaptation are used in these areas. The application of the adaptation principle in resolving the contradiction of the possibility of obtaining optimal characteristics of a high-temperature combustion chamber (CC) of a gas turbine engine under design (optimal) operating conditions and the impossibility of their implementation when these conditions change in the range of acceptable (non-design) gas turbine operation modes is considered in detail. The use of an adaptive approach in the development of promising gas turbine engines will significantly improve their characteristics and take into account unknown challenges.
- Open Access
- 1 January 2021
- Published by DAAAM International
- p. 0555-0565
Study and Analysis of Machine and Tool Parameters of Stainless-steel Turning Using Multi Coated Tools
- 1 January 2021
- Published by DAAAM International
- p. 0555-0565
Open AccessStudy and Analysis of Machine and Tool Parameters of Stainless-steel Turning Using Multi Coated Tools
- 1 July 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 260, 219-226
The Effect of the Cutting Parameters on the Machined Surface Roughness
From the invention of turning machine or lathe, some engineers are trying to increase the turning productivity. The increase of productivity is following after the breakout in instrumental area, such as the hard alloy instrument and resistance to wear cutting surfaces. The potential of cutting speed has a certain limit. New steel marks and cutting surfaces types allow significantly increase cutting and turning speeds. For the most operation types the productivity increase begins from the feeding increase. But the increase of feeding goes together with machined surface result decreasement. Metal cutting with high feeding is one of the most actual problems in the increasing of manufacturing volume but there are some problems one of them is the cutting forces increasement and larger metal removal rate, which decrease the cutting tool life significantly. Increasing of manufacturing volume, going together with the cutting instrument technology and material evolution, such as the invention of the carbide cutting materials and wear resistant coatings such as TiC and Ti(C,N). Each of these coating have its own properties and functions in the metal cutting process. Together with this evolution the cutting tool geometry and machining parameters dependencies are researched. Traditionally for the decreasing the machining time of one part, the cutting parameters were increased, decreasing by this way the machining operation quantity. In our days the wear resistance of the cutting tools increasing and it is mostly used one or two machining operations (medium and fine finishing). The purpose of the topic is to represent the experimental results of the stainless steel turning process, using increased cutting speeds and feeding values, to develop advanced processing technology, using new modern coated cutting tools by CVD and PVD methods. After investigation of the machined surface roughness results, develop the mathematical model of the cutting process using higher values of the cutting parameters.
- 1 July 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 260, 219-226
The Effect of the Cutting Parameters on the Machined Surface Roughness
From the invention of turning machine or lathe, some engineers are trying to increase the turning productivity. The increase of productivity is following after the breakout in instrumental area, such as the hard alloy instrument and resistance to wear cutting surfaces. The potential of cutting speed has a certain limit. New steel marks and cutting surfaces types allow significantly increase cutting and turning speeds. For the most operation types the productivity increase begins from the feeding increase. But the increase of feeding goes together with machined surface result decreasement. Metal cutting with high feeding is one of the most actual problems in the increasing of manufacturing volume but there are some problems one of them is the cutting forces increasement and larger metal removal rate, which decrease the cutting tool life significantly. Increasing of manufacturing volume, going together with the cutting instrument technology and material evolution, such as the invention of the carbide cutting materials and wear resistant coatings such as TiC and Ti(C,N). Each of these coating have its own properties and functions in the metal cutting process. Together with this evolution the cutting tool geometry and machining parameters dependencies are researched. Traditionally for the decreasing the machining time of one part, the cutting parameters were increased, decreasing by this way the machining operation quantity. In our days the wear resistance of the cutting tools increasing and it is mostly used one or two machining operations (medium and fine finishing). The purpose of the topic is to represent the experimental results of the stainless steel turning process, using increased cutting speeds and feeding values, to develop advanced processing technology, using new modern coated cutting tools by CVD and PVD methods. After investigation of the machined surface roughness results, develop the mathematical model of the cutting process using higher values of the cutting parameters.