Jian Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jian Wu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Lanzhong Guo
Changshu Institute of Technology
5 shared publicationsTonggang Liu
College of Mechanical and Electrical Engineering, China University of Mining and Technology, Xuzhou, China
3 shared publicationsXinyong Li
Changshu Institute of Technology
3 shared publicationsKesheng Wang
Department of Mechanical and Industrial Engineering, Norwegian University of Science and Technology, Trondheim, Norway
2 shared publicationsKnut Sørby
Department of Mechanical and Industrial Engineering, Norwegian University of Science and Technology, Trondheim, Norway
2 shared publicationsPeijun Jiao
Changshu Institute of Technology
2 shared publications
Latest Publications
- 15 February 2025
- Published by Springer Nature
- p. 370-376
A Symmetric Differential Algorithm for Detecting the Action State of an Elevator Brake
- 15 February 2025
- Published by Springer Nature
- p. 370-376
A Symmetric Differential Algorithm for Detecting the Action State of an Elevator Brake
- Open Access
- 20 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 15 (6) , 1-11
Cross-Layer Feature Fusion and Decentration Aberration Correction of Circular Points for Automated Guided Vehicle Terminal Positioning
To address the visual detection and positioning challenge of the Automated Guided Vehicle (AGV) terminal, this study proposed a high-precision target recognition and positioning strategy based on cross-layer feature fusion and eccentricity error correction. In the remote coarse positioning stage, small number of receiver domains underwent continuous multi-layer convolution, which broadened the receptive field of a single element in the feature map of a small circular target. Next, a cross-layer connection feature pyramid was constructed, and the deconvolution module was utilized to enlarge the feature map and fuse it with the shallow features, focusing more on the fine-grained image recognition and enhancing the applicability of circular marker detection. In the near-end fine positioning stage, the factors impacting the deviation between the projection point of the circular feature center and the fitting center were analyzed. Based on this analysis, the deviation of the iterative fitting center was corrected to approximate the real center projection sub-pixel coordinates. The experimental results demonstrated that the proposed method achieved dynamic positioning accuracy of better than 2.0 mm, static positioning accuracy of better than 1.5 mm, and a false recognition rate of less than 1.33% in the range of 3 m from AGV to the tray. Consequently, this method has significant application potential in enabling rapid and stable terminal vision positioning.
- 20 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 15 (6) , 1-11
Open AccessCross-Layer Feature Fusion and Decentration Aberration Correction of Circular Points for Automated Guided Vehicle Terminal Positioning
To address the visual detection and positioning challenge of the Automated Guided Vehicle (AGV) terminal, this study proposed a high-precision target recognition and positioning strategy based on cross-layer feature fusion and eccentricity error correction. In the remote coarse positioning stage, small number of receiver domains underwent continuous multi-layer convolution, which broadened the receptive field of a single element in the feature map of a small circular target. Next, a cross-layer connection feature pyramid was constructed, and the deconvolution module was utilized to enlarge the feature map and fuse it with the shallow features, focusing more on the fine-grained image recognition and enhancing the applicability of circular marker detection. In the near-end fine positioning stage, the factors impacting the deviation between the projection point of the circular feature center and the fitting center were analyzed. Based on this analysis, the deviation of the iterative fitting center was corrected to approximate the real center projection sub-pixel coordinates. The experimental results demonstrated that the proposed method achieved dynamic positioning accuracy of better than 2.0 mm, static positioning accuracy of better than 1.5 mm, and a false recognition rate of less than 1.33% in the range of 3 m from AGV to the tray. Consequently, this method has significant application potential in enabling rapid and stable terminal vision positioning.
- 26 January 2023
- Published by Springer Nature
- p. 711-718
Design of an Automated Stereoscopic Warehouse Device Applied in Experimental Teaching
- 26 January 2023
- Published by Springer Nature
- p. 711-718
Design of an Automated Stereoscopic Warehouse Device Applied in Experimental Teaching
- 21 February 2021
- Published by Springer Nature in Tribology Letters
- Vol. 69 (2) , 1-6
A Pin-on-Disk Tribometer for Friction and Lubricating Performance in mm-Scale
- 21 February 2021
- Published by Springer Nature in Tribology Letters
- Vol. 69 (2) , 1-6
A Pin-on-Disk Tribometer for Friction and Lubricating Performance in mm-Scale
- 23 January 2021
- Published by Springer Nature
- p. 339-346
Effect of Lubricant Viscosity on the Friction Behavior of the mm-scale Specimen
- 23 January 2021
- Published by Springer Nature
- p. 339-346
Effect of Lubricant Viscosity on the Friction Behavior of the mm-scale Specimen
- 2 December 2020
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (3) , 035002
A measuring method for micro force based on MEMS planar torsional spring
In order to measure the micro force in a micro-nano device, a new measuring method for micro force is introduced. In this paper, a measuring system based on a micro-electro-mechanical systems (MEMS) planar torsional spring is presented, which contains a support block, MEMS planar torsional spring, a support arm, and a laser displacement detection system. The micro force has been obtained by measuring the moving distance of the light spot which is reflected by the MEMS planar torsional spring. The spring sample has been prepared with laser processing technology, and the stiffness is obtained by theoretical calculation, simulation, and calibration. The results show that the torsional stiffness of the MEMS planar torsional spring is 3.7181 Nm rad −1 . The measurement system has a measuring range of ±159 mN. The maximum error of mean in repeated measurement is 1.25% of the reference value, and the repeatability standard deviation is a maximum 4.44% of the reference value.
- 2 December 2020
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 32 (3) , 035002
A measuring method for micro force based on MEMS planar torsional spring
In order to measure the micro force in a micro-nano device, a new measuring method for micro force is introduced. In this paper, a measuring system based on a micro-electro-mechanical systems (MEMS) planar torsional spring is presented, which contains a support block, MEMS planar torsional spring, a support arm, and a laser displacement detection system. The micro force has been obtained by measuring the moving distance of the light spot which is reflected by the MEMS planar torsional spring. The spring sample has been prepared with laser processing technology, and the stiffness is obtained by theoretical calculation, simulation, and calibration. The results show that the torsional stiffness of the MEMS planar torsional spring is 3.7181 Nm rad −1 . The measurement system has a measuring range of ±159 mN. The maximum error of mean in repeated measurement is 1.25% of the reference value, and the repeatability standard deviation is a maximum 4.44% of the reference value.
- 3 January 2020
- Published by Springer Nature in Lecture Notes in Electrical Engineering
- p. 52-58
Effect of Cerium on Microstructure and Friction of MoS2 Coating
- 3 January 2020
- Published by Springer Nature in Lecture Notes in Electrical Engineering
- p. 52-58
Effect of Cerium on Microstructure and Friction of MoS2 Coating
- 3 January 2020
- Published by Springer Nature
- p. 59-66
A Machine Vision Method for Elevator Braking Detection
- 3 January 2020
- Published by Springer Nature
- p. 59-66
A Machine Vision Method for Elevator Braking Detection
- 15 December 2018
- Published by Springer Nature
- p. 694-700
Study on the Torque of Sleeve Permanent Magnetic Couplings
- 15 December 2018
- Published by Springer Nature
- p. 694-700
Study on the Torque of Sleeve Permanent Magnetic Couplings