HAHassan Obaid Abbas

Hassan Obaid Abbas

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hassan Obaid Abbas has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Controlled Liquefaction of Earth Dam under Dual Water Level Conditions

    by Ahmed M. Mahdi, Hassan O. Abbas, Saad Sh. Sammen

    This study investigates the seismic response and liquefaction potential of the Al-Adhaim Dam under maximum and normal reservoir water levels using coupled hydromechanical finite element analysis in GeoStudio Quake/W 2025. Dynamic loading was applied using the Ali Al-Gharbi earthquake record, and six monitoring points were analyzed for pore water pressure, effective stresses, displacement, acceleration, and Cycle Stress Ratio (CSR). At maximum water level, upstream pore pressure increased from 1000 kPa to 1200 kPa (≈20%) at peak shaking (t = 14 s), while vertical effective stress at a critical downstream–upstream transition point decreased from 750 kPa to 420 kPa (≈44% reduction). The highest CSR values were recorded in upstream saturated zones (CSR = 3.805 and 3.498), compared to a negligible value downstream (CSR = 0.065). Under normal water level, pore pressures were limited to 400–700 kPa with lower effective stress loss and reduced CSR values, indicating improved stability. The results confirm that maximum reservoir level represents the governing seismic condition, significantly increasing liquefaction susceptibility in deep upstream saturated zones.

  • Open Access

    Parametric Study of Pullout Resistance of Anchored Pile Group under Inclined Loading in Dense Sand

    by Safa Adnan Qais, Hassan Obaid Abbas

    Screw pile foundations are gaining significance in geotechnical engineering due to their rapid installation, high tensile capacity, and effectiveness in supporting structures under uplift loads, like transmission towers and offshore platforms. Despite their extensive use, little is known about how screw pile groups behave under inclined pullout loading. This study investigates the pullout performance of single and double helix pile groups in sandy soil with a relative density 68%, under inclined pullout loads at angles of 10°, 20°, and 45° from horizontal. An experimental program was conducted on groups with spacing (1.5Dh and 4.5Dh) (where Dh is the helix diameter 20mm), the shaft diameter 10 mm and embedded length ratio (L/D = 36) to evaluate the influence of load inclination, number of helix and pile spacing on group inclined pullout capacity. According to the results, when pile spacing increased from (1.5Dh to 4.5Dh), inclined pullout capacity improved by roughly (18 to 30%) because less interactions occurred. Additionally, double-helix piles better than single-helix piles in terms of pullout resistance under all conditions evaluated, with an improvement of 19%. when the inclination angle decreased, the pullout capacity increased. The findings provide useful information for screw pile group design under inclined pullout loads.


  • Open Access

    Performance of Batter Piles Supported Sheet Wall Subjected to Seepage and Cyclic Loading Adjacent Strip Footing

    by Shaimaa Ahmed Abdulhadi, Hassan Obaid Abbas

    One of the earliest methods of anchoring in civil engineering projects is sheet walls. A practical experiment was carried out in this work on a sheet wall that was laterally anchored in sandy soil for 100 cycles at a cyclic loading ratio (CLR) of 40% and seepage conditions. The length of the anchor bar (40 cm), the length of the pile (40 cm), the angles between the inclined piles (10°, 15°, and 25°), and the distance between the anchor bars (S/H = 1/3, 2/3, and 1) were among the characteristics that were examined. Furthermore, the ground surface was subjected to a linear load of 5 kPa. According to the test results, the lateral displacement of the sheet wall increased by (52-73) %, (78-82) %, and (2-10) % for angles between batter piles (θ =10°, 15°, and 25°), respectively, when the distance between the anchor bars was increased from 1/3 to 2/3 and subsequently to 1. As the distance between the anchor bars increase from 1 to 2/3 and finally to 1/3, the tilting of the strip foundation and the vertical settling close to the metal sheet wall reduced. When the distance between the anchor bars was 1/3, the anchored metal sheet wall system performed better and was safer under cyclic loads and seepage condition.

  • Open Access

    Cyclic Behavior of Sheet Pile Wall Under Seepage Anchored Conditions

    by Shaimaa A. Abdul Hadi, Hassan O. Abbas

    Sheet pile walls have been considered the hoariest anchoring techniques used in civil engineering projects. In this study, experimental work was achieved on a laterally anchored sheet pile wall installed below a cycling load in sandy soil with a ratio (CLR) of 40% for 100 cycles. Several parameters were considered, including anchor rod length of (40 cm), pile length (30 cm), and angles between batter piles 100, 150, and 250). In addition, a linear load of 5 kPa applied on ground surface near sheet pile wall and a spacing between anchors of 10 cm was considered. The batter piles were installed at a distance of 40 cm from the sheet pile wall. The test results showed that the increase of angles between batter piles from 10° to 15° and 25° leads to a reduction of the lateral displacement of the sheet pile wall by 7.1% and 64.3%, respectively. Strip footing tilting and total settlement near the sheet pile wall reduced as the angles between anchored batter piles increased from 10° to 15° and 25°. The wall system, which is made from anchored sheet pile, has been exposed to cyclic load was effective and safer when the inclination angle between the batter piles is 25°.

  • Open Access

    Mapping of Allowable Bearing Capacity for Square and Strip Footing of Al-Khalis City

    by Abeer Jasim, Hassan Obaid

    This research uses Geographic Information Systems (GIS) to assess the allowable bearing capacity of shallow foundations in AI-Khalis District, located along the Diyala River about 20 kilometres northeast of Baghdad within the Diyala Governorate. From 12 exploration sites, each containing several boreholes, around 35 test records were gathered at different depths. The database contained unit weights, soil classification, and results from the Standard Penetration Test (SPT). The correlation and modification of the SPT results were used to calculate the undrained shear strength (Cu). Subsequently. Terzaghi's equations were used to determine the permissible soil bearing capacity for two types of foundations: square (B= 1.5 m) and strip (B 1 m) at excavation depths of 1 and 2 metres. The data were then collected in an Excel file and entered into the Geographic Information System (GIS) to produce maps. The results revealed a significant variation in the permissible soil bearing capacity across different depths, i.e., it gradually increases with depth. This study aims to provide geotechnical engineers with an initial view of the type of foundation and the number of layers.

  • Open Access

    Influence of Ali Al -Gharbi Earthquake on Braced Excavation in Silty Clay Soil (Numerical Study)

    by Hadeel Khaleel Abd Al-Ameer, Hassan Obaid Abbas

    The design of the braced excavation system is one of the important and necessary matters for the implementation of various projects. The braced excavation system is used to support excavations in temporary projects, so there are shortcomings in the study of this aspect, although sometimes there are many projects that take long periods of time especially the projects of underground tunnels and high buildings. This was the main reason for the study. Therefore, the possibility of exposing the drilling system to earthquakes is great, especially in seismically active areas. If the drilling system is exposed to an earthquake, it can cause great human and material losses, so it must be designed against earthquakes so that ensure complete collapse and failure does not occur. This study aims to investigate the behavior of braced excavations under the influence of the Ali Al-Gharbi earthquake in both x- and y- directions. A numerical study is carried out on braced excavation system of (14×6) m and depth 9m using software Plaxis 3D. The braced excavation system consists of three type of bracing system with three levels of strut and wales connected with sheet pile wall to support sides of excavation and prevent them from collapsing. The results of study showed that the horizontal displacement of braced excavation system is (100-155) % more than vertical displacement (settlement) with seismic time when system is subjected to Ali Al-Gharbi earthquake in both directions with the other factors remaining constant. The stiffness of sheet pile wall also play an important role increases and decreases lateral displacement in both direction. Also, the results showed that the movement of of braced excavation system depends on several factors like as type of soil, time acceleration and the direction of earthquake. Settlement of Ali Al-Gharbi earthquake in Y- direction is 13% more than in X-direction.


  • Open Access

    The Behavior of Braced Excavation in Silty Clay Soil under El-Centro Seismic

    by Hadeel K. Abd- Alameer, Hassan O. Abbas

    Braced excavation is one of the important systems used to support soil from collapse during excavation. A braced excavation system may be exposed to seismic load and undergoes more forces through the significant vibration of the surrounding soil in addition to the static and lateral loads of soil and nearby structures. The investigation of the braced excavation under the effect of earthquake behavior is still limited or poorly described. Further, this paper presents a numerical study to evaluate the vertical settlement and horizontal displacement of sheet pile wall embedded in silty clay soil in Baqubah city under the influence of the acceleration time history of the 1940 El-Centro earthquake. The study utilized the software PLAXIS 3D. A three-dimensional analysis of the braced system with dimensions of 14m×6m and an excavation depth of 7m was achieved. Three levels of strut and wale layers were used, and five struts for each level. The penetration depth for the sheet pile wall was 9m. The study showed that the El-Centro earthquake laterally moved the braced excavation system as a block mass due to the existence of the excavation system in soft silty clay. The lateral displacement reached approximately 150mm. The differences in lateral earth pressure on sheet pile wall depth a few seconds before and after the earthquake were very small.