Barbara Swatowska
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Barbara Swatowska has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
Tomasz Stapinski
AGH University of Science and Technology, Department of Electronics, Mickiewicza Av. 30, 30-059 Kraków, Poland
6 shared publicationsPiotr Panek
3 shared publications- Gabriela Lewińska
Institute of Electronics, AGH University of Krakow, 30 Mickiewicza Ave, 30-059 Krakow, Poland
2 shared publications - Grzegorz Wroblewski
Warsaw University of Technology
2 shared publications Janusz Jaglarz
Institute of Physics, Cracow University of Technology, Kraków, Poland
2 shared publications- Katarzyna Gawlińska-Nęcek
Institute of Metallurgy and Materials Science PAS, Reymonta 25, 30-059 Krakow, Poland
2 shared publications
Latest Publications
- Open Access
The Influence of the Solar Cell Structure and Material Composition on Its Quantum Efficiency
This study examines the influence of device architecture and substrate materials on the external quantum efficiency (EQE) of high-performance solar cells. A diverse array of photovoltaic technologies was evaluated, including formamidinium lead iodide CH5N2PbI3 (FAPI) perovskite cells and various silicon-based designs, such as Passivated Emitter and Rear Cell (PERC), Back Integrated Contact (BIC), and Bifacial structures. Quantum characteristics were determined through wavelength-dependent photocurrent measurements utilizing a precision monochromator system. Our results reveal that device structure is a primary determinant of charge carrier collection efficiency; specifically, Bifacial and PERCs achieved superior short-circuit current densities (Jsc) of 40.98 mA/cm2 and 39.42 mA/cm2, respectively. Notably, the EQE(λ) profile of Bifacial cells under n-side illumination exhibits a near-ideal rectangular shape, indicating an optimized spectral response throughout the operating spectrum. Furthermore, the analysis investigates the role of surface recombination velocity and the efficacy of advanced passivation layers—specifically Al2O3 and SiNx—in enhancing quantum performance by mitigating recombination state density. Our findings demonstrate that the strategic integration of advanced passivation layers (Al2O3 and SiNx) with optimized architectures, such as PERC and Bifacial designs, is paramount for maximizing charge carrier collection and achieving record-high current densities reaching 40.98 mA/cm2. A comprehensive analysis of solar cell performance involves spectral response (SR) and external quantum efficiency (EQE) as functions of wavelength. Additionally, SR-based current density analysis enables more accurate evaluation of cell parameters than standard I–V characterization.
Open AccessThe Influence of the Solar Cell Structure and Material Composition on Its Quantum Efficiency
This study examines the influence of device architecture and substrate materials on the external quantum efficiency (EQE) of high-performance solar cells. A diverse array of photovoltaic technologies was evaluated, including formamidinium lead iodide CH5N2PbI3 (FAPI) perovskite cells and various silicon-based designs, such as Passivated Emitter and Rear Cell (PERC), Back Integrated Contact (BIC), and Bifacial structures. Quantum characteristics were determined through wavelength-dependent photocurrent measurements utilizing a precision monochromator system. Our results reveal that device structure is a primary determinant of charge carrier collection efficiency; specifically, Bifacial and PERCs achieved superior short-circuit current densities (Jsc) of 40.98 mA/cm2 and 39.42 mA/cm2, respectively. Notably, the EQE(λ) profile of Bifacial cells under n-side illumination exhibits a near-ideal rectangular shape, indicating an optimized spectral response throughout the operating spectrum. Furthermore, the analysis investigates the role of surface recombination velocity and the efficacy of advanced passivation layers—specifically Al2O3 and SiNx—in enhancing quantum performance by mitigating recombination state density. Our findings demonstrate that the strategic integration of advanced passivation layers (Al2O3 and SiNx) with optimized architectures, such as PERC and Bifacial designs, is paramount for maximizing charge carrier collection and achieving record-high current densities reaching 40.98 mA/cm2. A comprehensive analysis of solar cell performance involves spectral response (SR) and external quantum efficiency (EQE) as functions of wavelength. Additionally, SR-based current density analysis enables more accurate evaluation of cell parameters than standard I–V characterization.
- Open Access
- 16 June 2026
- Published by Elsevier in SSRN Electronic Journal
Correlation between phase composition and oxygen sensing response in single- and dual-doped copper oxide
Copper oxides are prominent candidates for gas sensing applications due to their inherent p-type semiconducting nature, high chemical and ambient stability, and low cost. In this work, we investigate the influence of potassium, calcium, and Ca/Zn dual doping on the phase composition, optical properties, and oxygen sensing response of copper oxide thin films. XRD analysis reveals a mixed CuO/Cu2O system, where the relative phase composition is strongly affected by dopant incorporation, which preferentially stabilizes the Cu2O phase. Gas sensing measurements demonstrate that single potassium and calcium doping does not significantly enhance the response magnitude but effectively accelerates sensor kinetics at elevated temperature (300°C), reducing response time from 195 s for the reference sample to 157 s and 55 s for K- and Ca- doped samples, respectively. In contrast, co-doping of copper oxide by Ca and Zn simultaneously promotes efficient oxygen adsorption, thereby enhancing the sensor response and shortening the response time within the operating temperature range of 150–250°C.
- 16 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCorrelation between phase composition and oxygen sensing response in single- and dual-doped copper oxide
Copper oxides are prominent candidates for gas sensing applications due to their inherent p-type semiconducting nature, high chemical and ambient stability, and low cost. In this work, we investigate the influence of potassium, calcium, and Ca/Zn dual doping on the phase composition, optical properties, and oxygen sensing response of copper oxide thin films. XRD analysis reveals a mixed CuO/Cu2O system, where the relative phase composition is strongly affected by dopant incorporation, which preferentially stabilizes the Cu2O phase. Gas sensing measurements demonstrate that single potassium and calcium doping does not significantly enhance the response magnitude but effectively accelerates sensor kinetics at elevated temperature (300°C), reducing response time from 195 s for the reference sample to 157 s and 55 s for K- and Ca- doped samples, respectively. In contrast, co-doping of copper oxide by Ca and Zn simultaneously promotes efficient oxygen adsorption, thereby enhancing the sensor response and shortening the response time within the operating temperature range of 150–250°C.
- Open Access
Controlling the Functional Properties of K0.5Bi0.5TiO3 Ceramics Using E-Poling
Lead-free K0.5Bi0.5TiO3 (KBT) ceramics were prepared using a finely tuned convectional solid-state reaction method. Their phase transitions in unpoled and poled states were examined. The temperature-dependent evolution of the reflections sensitive to structural changes and their 2Θ-positions indicated two temperature-driven phase transitions: tetragonal–tetragonal at about 200 °C, and tetragonal–cubic at around 400 °C. These structural transformations are further corroborated by studies examining Raman spectroscopy, dielectric properties, and mechanical properties. It was demonstrated that a prior E-field poling process significantly influences the polar state, causing an increase in the local degree of order, as well as the transformation of the cubic phase into the tetragonal one. This stabilizes and widens the temperature range of the ferroelectric phase. It was found that phase transformations in KBT are accompanied by a softening of the mechanical behavior similarly to improper ferroelastic transformations. The results demonstrate that KBT possesses favorable structural, dielectric, and mechanical characteristics, making it a potential candidate for electronic applications. The present study provides a clear understanding of the multi-scale structural behavior in multi-phase KBT, bridging micro-heterogeneity behaviors and macro-properties, and demonstrates an effective method of tuning the properties of KBTs by E-poling with a low electric field.
Open AccessControlling the Functional Properties of K0.5Bi0.5TiO3 Ceramics Using E-Poling
Lead-free K0.5Bi0.5TiO3 (KBT) ceramics were prepared using a finely tuned convectional solid-state reaction method. Their phase transitions in unpoled and poled states were examined. The temperature-dependent evolution of the reflections sensitive to structural changes and their 2Θ-positions indicated two temperature-driven phase transitions: tetragonal–tetragonal at about 200 °C, and tetragonal–cubic at around 400 °C. These structural transformations are further corroborated by studies examining Raman spectroscopy, dielectric properties, and mechanical properties. It was demonstrated that a prior E-field poling process significantly influences the polar state, causing an increase in the local degree of order, as well as the transformation of the cubic phase into the tetragonal one. This stabilizes and widens the temperature range of the ferroelectric phase. It was found that phase transformations in KBT are accompanied by a softening of the mechanical behavior similarly to improper ferroelastic transformations. The results demonstrate that KBT possesses favorable structural, dielectric, and mechanical characteristics, making it a potential candidate for electronic applications. The present study provides a clear understanding of the multi-scale structural behavior in multi-phase KBT, bridging micro-heterogeneity behaviors and macro-properties, and demonstrates an effective method of tuning the properties of KBTs by E-poling with a low electric field.
- Open Access
Application Properties of ZnO and AZO Thin Films Obtained by the ALD Method
The thin layers of ZnO and ZnO: Al (Al doped zinc oxide—AZO) were deposited by the atomic deposition layer (ALD) method on silicon and glass substrates. The structures were deposited using diethylzinc (DEZ) and deionized water as zinc and oxygen precursors. A precursor of trimethylaluminum (TMA) was used to introduce the aluminum dopant. The present study of ALD-deposited ZnO and AZO films was motivated by their applications in photovoltaics. We attempted to expose several properties of such films. Structural, optical (including ellipsometric measurements) and electrical investigations were performed. We discussed the relations between samples doped with different Al fractions and their properties.
Open AccessApplication Properties of ZnO and AZO Thin Films Obtained by the ALD Method
The thin layers of ZnO and ZnO: Al (Al doped zinc oxide—AZO) were deposited by the atomic deposition layer (ALD) method on silicon and glass substrates. The structures were deposited using diethylzinc (DEZ) and deionized water as zinc and oxygen precursors. A precursor of trimethylaluminum (TMA) was used to introduce the aluminum dopant. The present study of ALD-deposited ZnO and AZO films was motivated by their applications in photovoltaics. We attempted to expose several properties of such films. Structural, optical (including ellipsometric measurements) and electrical investigations were performed. We discussed the relations between samples doped with different Al fractions and their properties.
- 5 January 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 137, 106830
The investigation of PV systems quantum efficiency in various irradiation condition
- 5 January 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 137, 106830
The investigation of PV systems quantum efficiency in various irradiation condition
- 1 July 2019
- Published by Emerald Publishing in Microelectronics International
- Vol. 36 (3) , 90-94
The influence of emitter resistance on the electrical parameters of mono- and multicrystalline silicon solar cells
Purpose: The purpose of this study was the comparison and analysis of the electrical parameters of two kinds of silicon solar cells (mono- and multicrystalline) of different emitter resistance. Design/methodology/approach: By controlling of diffusion parameters, silicon mono- (Cz-Si) and multicrystalline (mc-Si) solar cells with different emitter resistance values were produced – 22 and 48 Ω/□. On the basis of current-voltage measurements of cells and contact resistance mapping, the properties of final solar cells based on two different materials were compared. Additionally, the influence of temperature on PV cells efficiency and open circuit voltage (Uoc) were investigated. The PC1D simulation was useful to determine spectral dependence of external quantum efficiency of solar cells with different emitter resistance. The silicon solar cells of 25 cm2 area and 240 µm thickness were investigated. Findings: Considering the all stages of cell technology, the best structure is silicon solar cell with sheet resistance (Rsheet) of 45-48 Ω/□. Producing of an emitter with this resistance allowed to obtain cells with a fill factor between 0.725 and 0.758, Uoc between 585 and 612 mV, short circuit current (Isc) between 724 and 820 mA. Originality/value: Measurements and analysis confirmed that mono- and multicrystalline silicon solar cells with 48 Ω/□ emitter resistance have better parameters than cells with Rsheet of 22 Ω/□. The contact resistance is the highest for mc-Si with Rsheet of 48 Ω/□ and reaches the value 3.8 Ωcm.
- 1 July 2019
- Published by Emerald Publishing in Microelectronics International
- Vol. 36 (3) , 90-94
The influence of emitter resistance on the electrical parameters of mono- and multicrystalline silicon solar cells
Purpose: The purpose of this study was the comparison and analysis of the electrical parameters of two kinds of silicon solar cells (mono- and multicrystalline) of different emitter resistance. Design/methodology/approach: By controlling of diffusion parameters, silicon mono- (Cz-Si) and multicrystalline (mc-Si) solar cells with different emitter resistance values were produced – 22 and 48 Ω/□. On the basis of current-voltage measurements of cells and contact resistance mapping, the properties of final solar cells based on two different materials were compared. Additionally, the influence of temperature on PV cells efficiency and open circuit voltage (Uoc) were investigated. The PC1D simulation was useful to determine spectral dependence of external quantum efficiency of solar cells with different emitter resistance. The silicon solar cells of 25 cm2 area and 240 µm thickness were investigated. Findings: Considering the all stages of cell technology, the best structure is silicon solar cell with sheet resistance (Rsheet) of 45-48 Ω/□. Producing of an emitter with this resistance allowed to obtain cells with a fill factor between 0.725 and 0.758, Uoc between 585 and 612 mV, short circuit current (Isc) between 724 and 820 mA. Originality/value: Measurements and analysis confirmed that mono- and multicrystalline silicon solar cells with 48 Ω/□ emitter resistance have better parameters than cells with Rsheet of 22 Ω/□. The contact resistance is the highest for mc-Si with Rsheet of 48 Ω/□ and reaches the value 3.8 Ωcm.
- 2 July 2018
- Published by Emerald Publishing in Microelectronics International
- Vol. 35 (3) , 177-180
Antireflective and passivation properties of the photovoltaic structure with Al2O3 layer of different thickness
Purpose: The purpose of this study is to verify the possibility of applying alumina (Al2O3) as the passivation and antireflective coating in silicon solar cells. Design/methodology/approach: Model of a studied structure contains the following layers: Al2O3/n+/n-type Si/p+/Al2O3. Optical parameters of the aluminium oxide films on silicon wafers were measured in the range of wavelengths from 250 to 1,400 nm with a spectrophotometer Perkin Elmer Lambda 900. The minority carrier lifetime at the start of the n-type Si base material and after each of the next technological process was analysed by a quasi-steady-state photoconductance technique. The electrical parameters of the solar cells fabricated with four different thickness of the Al2O3 layer were determined on the basis of the current-voltage (I-V) characteristics. The silicon solar cells of 25 cm2 area and 300 µm thickness were investigated. Findings: The optimum thickness of alumina as passivation layer is 90 nm. However, considering also antireflective properties of the first layer of a photovoltaic cell, the best structure is silicon with alumina passivation layer of 30 nm thickness and with TiO2 antireflective coatings of 60 nm thickness. Such solution has allowed to produce the cells with the fill factor of 0.77 and open circuit voltage of 618 mV. Originality/value: Measurements confirmed the possibility of applying the Al2O3 as a passivation and antireflective coating (obtained by atomic layer deposition method) for improving the efficiency of solar cells.
- 2 July 2018
- Published by Emerald Publishing in Microelectronics International
- Vol. 35 (3) , 177-180
Antireflective and passivation properties of the photovoltaic structure with Al2O3 layer of different thickness
Purpose: The purpose of this study is to verify the possibility of applying alumina (Al2O3) as the passivation and antireflective coating in silicon solar cells. Design/methodology/approach: Model of a studied structure contains the following layers: Al2O3/n+/n-type Si/p+/Al2O3. Optical parameters of the aluminium oxide films on silicon wafers were measured in the range of wavelengths from 250 to 1,400 nm with a spectrophotometer Perkin Elmer Lambda 900. The minority carrier lifetime at the start of the n-type Si base material and after each of the next technological process was analysed by a quasi-steady-state photoconductance technique. The electrical parameters of the solar cells fabricated with four different thickness of the Al2O3 layer were determined on the basis of the current-voltage (I-V) characteristics. The silicon solar cells of 25 cm2 area and 300 µm thickness were investigated. Findings: The optimum thickness of alumina as passivation layer is 90 nm. However, considering also antireflective properties of the first layer of a photovoltaic cell, the best structure is silicon with alumina passivation layer of 30 nm thickness and with TiO2 antireflective coatings of 60 nm thickness. Such solution has allowed to produce the cells with the fill factor of 0.77 and open circuit voltage of 618 mV. Originality/value: Measurements confirmed the possibility of applying the Al2O3 as a passivation and antireflective coating (obtained by atomic layer deposition method) for improving the efficiency of solar cells.
- Open Access
- 1 March 2018
- Published by Walter de Gruyter GmbH
Properties of a-Si:N:H films beneficial for silicon solar cells applications
Amorphous silicon-nitride thin films a-Si:N:H were obtained by plasma enhanced chemical vapour deposition (PECVD) method from SiH 4+ NH 3at 13.56 MHz. The process parameters were chosen to obtain the films of properties suitable for optoelectronic and mechanical applications. FTIR analysis of a-Si:N:H films indicated the presence of numerous hydrogen bonds (Si-H and N-H) which passivate structural defects in multicrystalline silicon and react with impurities. The morphological investigations show that the films are homogeneous. The deposition of a-Si:N:H layers leads to the decrease in friction coefficient of used substrates. Optical properties were optimised to obtain the films of low effective reflectivity, large energy gap E gfrom 2.4 to 2.9 eV and refractive index in the range of 1.9 to 2.2. Reduction of friction coefficient for monocrystalline silicon after covering with a-Si:N:H films was observed: from 0.25 to 0.18 for 500 cycles.
- 1 March 2018
- Published by Walter de Gruyter GmbH
Open AccessProperties of a-Si:N:H films beneficial for silicon solar cells applications
Amorphous silicon-nitride thin films a-Si:N:H were obtained by plasma enhanced chemical vapour deposition (PECVD) method from SiH 4+ NH 3at 13.56 MHz. The process parameters were chosen to obtain the films of properties suitable for optoelectronic and mechanical applications. FTIR analysis of a-Si:N:H films indicated the presence of numerous hydrogen bonds (Si-H and N-H) which passivate structural defects in multicrystalline silicon and react with impurities. The morphological investigations show that the films are homogeneous. The deposition of a-Si:N:H layers leads to the decrease in friction coefficient of used substrates. Optical properties were optimised to obtain the films of low effective reflectivity, large energy gap E gfrom 2.4 to 2.9 eV and refractive index in the range of 1.9 to 2.2. Reduction of friction coefficient for monocrystalline silicon after covering with a-Si:N:H films was observed: from 0.25 to 0.18 for 500 cycles.
- 22 December 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10175, 101750V-101750V-9
Boron liquid solution deposited by spray method for p-type emitter formation in crystalline Si solar cells
- 22 December 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10175, 101750V-101750V-9
Boron liquid solution deposited by spray method for p-type emitter formation in crystalline Si solar cells
- 22 December 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10175, 101751C-101751C-7
a-SiCxNy:H thin films for applications in solar cells as passivation and antireflective coatings
- 22 December 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10175, 101751C-101751C-7
a-SiCxNy:H thin films for applications in solar cells as passivation and antireflective coatings