PBPeter Barbosa

Peter Barbosa

*This is an algorithmically generated author record based on publicly available information.

Peter Barbosa has a total of 83 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Highly Efficient GaN-Based Three-Phase Three-Level Flying Capacitor Inverter With Integrated Triangular Current Mode Control and Clamped Discontinuous Pulsewidth Modulation

    by Nidhi Haryani, Ripun Phukan, Laszlo Huber, Anup Anurag, Juan Ruiz, Peter Barbosa

    Multi-level Flying Capacitor (FC) converters enable the use of lower voltage devices for high voltage systems resulting in high efficiency and high density through the effect of frequency multiplication. Soft-switched integrated Triangular Current Mode (iTCM) based FC inverters can push the efficiency further. iTCM has the advantage of ZVS turn-on like TCM while reducing the ripple on the grid side by inserting an LC-branch between grid-side inductor and the PWM bridge. In this letter, a Gallium Nitride (GaN) based three-phase three-level FC inverter operating in iTCM + Clamped Discontinuous Pulse Width Modulation (DPWM) is presented with the addition of just one LC-branch per phase. The efficiency achieved is 99.16% at 600 V, 11 kW and a minimum inductor current frequency of 300 kHz which is much higher than state-of-the-art two-level converters operating in TCM/ iTCM. As compared to TCM and conventional iTCM, iTCM+DPWM leads to 70% and 25% lower ripple on grid current respectively, thus paving the path for EMI filter size reduction with soft-switched multi-level converters.


  • Matrix-Based Inductor Structure for MV Applications

    by Anup Anurag, Rudy Wang, Peter Barbosa

    Acrucial aspect of designing medium voltage (MV) converters is the design of the MV inductor, which demands a reliable insulation design that can achieve good performance, manufacturability, modularity, and repeatability. This article shows the design and development of a novel modular medium voltage high-frequency inductor using a matrix-based concept to achieve both the inductance requirement and high-voltage insulation. The concept uses the air gap of the inductor to achieve the required inductance and medium-voltage insulation. The design is carried out using five separate cores and the partial discharge (PD) voltage of 5 kV RMS between the individual core structures is observed experimentally, which translates to a PD voltage of 20 kV for the entire structure. Experimental results in a 20 kW, 10 kV silicon carbide (SiC) mosfet-based converter has been shown to demonstrate the feasibility of the inductor design in high-voltage applications. The medium-voltage matrix inductor design is aimed at providing an air insulated, modular, and easily manufacturable solution to design medium voltage magnetic structures for commercial applications.

  • PCB Based Inductor Structure for MV Applications

    by Anup Anurag, Peter Barbosa

    Silicon carbide (SiC) power semiconductor devices have opened up new areas of applications such as solid-state transformers for medium voltage (MV) high power applications. One of the key enabling factor for MV systems is the design of the MV inductor. The use of inductors in MV systems calls for a reliable insulation design of the inductor along with achieving good performance and more importantly offering good manufacturability and repeatability for the design. This letter focuses on the design of high frequency inductors and demonstrates a novel potting-free, simple to manufacture structure of the MV inductor using PCB based windings. The structure takes advantage of the voltage distribution in the windings to grade the electric field inside the PCB structure, and thus achieve a partial-discharge (PD) free operation. A peak PD inception voltage of 15.5 kV is showcased experimentally for the structure. This PCB based structure is also compared with other designs to demonstrate the advantages and challenges brought upon by the proposed designs. PD and electric field simulation results validate the design and operation of the inductor structures. The MV inductor design is aimed at providing a reliable and repeatable method to design and manufacture MV inductors for commercial applications.


  • Common Source Inductance Compensation Technique for Dynamic Current Balancing in SiC MOSFETs Parallel Operations

    by Boyi Zhang, Ruxi Wang, Peter Barbosa, Qianyi Cheng, Yu-Hsuan Tsai, Wen-Sheng Wang, Wen-Shang Lai, Fu-Yuan Shih

    In high-current applications such as traction inverters, SiC MOSFETs are paralleled to increase the current rating. One major issue with paralleling SiC MOSFETs is the dynamic current imbalance. The unbalanced dynamic current could lead to severe device and system failures. A well-known root cause of dynamic current imbalance is the parasitic inductance imbalance due to asymmetrical layout. In this paper, a common source inductance (CSI) compensation technique is proposed for SiC MOSFETs in parallel operations to reduce the dynamic current imbalance due to layout asymmetry. With the proposed technique, the dynamic current among paralleled switches is evenly distributed even when the layout is not symmetrical. The improved current sharing is achieved by designing the common source inductance of each paralleled device inversely proportional to its power loop inductance. Because of the balanced dynamic current, the reliability of the circuit with the proposed layout can be significantly improved. In addition, the proposed CSI compensation technique could help reduce the peak current in case of a short circuit, hence improving module reliability. The proposed technique is an easy-to-implement design that requires no additional components. A half-bridge configuration with SiC discrete devices in parallel and a multi-chip power module with SiC dies in parallel are built to verify the effectiveness of the proposed technique. The proposed technique could improve the current sharing in both prototypes.


  • High-Voltage Isolated Power Supply Structure for Gate Drivers of Medium-Voltage SiC Devices

    by Anup Anurag, Peter Barbosa

    This letter proposes two novel gate driver isolation structures with potted PCB windings and cylindrical rod-based cores to drive medium voltage (MV) silicon carbide (SiC) devices. The first design uses two cylindrical rod cores, each for the primary and secondary winding, and uses a coupling coil to improve the magnetic coupling between the primary and the secondary side. The second design improves upon the first design and uses a single cylindrical core for both the primary and the secondary windings, eliminates the coupling coil, and brings upon the ability to drive a half-bridge structure. Both structures are designed to maintain the required insulation standards. The isolation structures achieve a peak partial discharge (PD) voltage greater than 15 kV peak, with an isolation capacitance within 5 pF. The structure of the PCB windings and the ferrite cores for the designs provides excellent repeatability and easy manufacturability. Experimental results validate the design and operation of the gate driver isolation structures.


  • Design and Optimization of an Integrated Resonant Inductor With High-Frequency Transformer for Wide Gain Range DC–DC Resonant Converters in Electric Vehicle Charging Applications

    by Satyaki Mukherjee, Peter Barbosa

    Large-scale adoption of wide band gap semiconductors in switched-mode power converters enables miniaturization of power electronic systems. With switching frequencies approaching a few hundred kilohertz–megahertz range, efficient and compact design of magnetic components are crucial for future generation power supplies in data centers or electric vehicle (EV) applications. In a typical two-stage AC–DC power supply, the DC–DC stage is often constructed using a resonant converter with galvanic isolation provided by a high-frequency transformer. In such systems, the integration of an inductor in the resonant network with the transformer helps improve power density and reduces component count and cost. However, the integration of magnetic components can result in increased losses, deteriorating the performance of the power conversion system. In this article, a magnetic structure along with an optimization methodology is presented to integrate a predefined resonant inductor as leakage inductance of the high-frequency transformer achieving minimum penalty on converter efficiency using planar core geometry and printed circuit board (PCB)-based windings. The proposed methodology is applied to integrate a $\rm{7.8} \rm{\mu }\rm{H}$ inductor with a 2:1 transformer for a 6.6-kW, 500-kHz LCL-T resonant DC–DC stage utilizing gallium nitride transistors in an onboard battery charging converter. On the prototype converter using the optimized integrated magnetic component, a peak efficiency of 98.4% was obtained using PCB windings. Furthermore, the integrated magnetic component achieved 64-kW/L power density in the demonstrator prototype.


  • Analysis, Design, and Performance Evaluation of SiC Active Soft-Switching Cell for 1-ph/3-ph Universal Voltage Input PFC for On-Board Charger Applications

    by Tomas Sadilek, Laszlo Huber, Yungtaek Jang, Peter Barbosa, Iqbal Husain

    In this article, a detailed analysis, design, and experimental evaluation of a continuous-conduction-mode, pulsewidth modulated, boost-type active soft-switching cell suitable for 1-ph/3-ph universal input voltage power factor correction (PFC) rectifier for on-board charging applications is introduced. The soft-switching cell features zero-voltage switching and simple control. The evaluation of the concept was performed on a 1-ph/3-ph combo 7.2-kW/12.5-kW prototype designed to operate at 230 V RMS 1–ph and 480 V RMS 3-ph line input and deliver 650–750 V output. At full load and 150 kHz switching frequency, the prototype achieves 98.8% efficiency in 3-ph operation and 98% efficiency in 1-ph interleaved operation. The soft-switching PFC concept naturally morphs between an interleaved totem-pole converter for 1-ph ac line voltage and a 3-ph converter for 3-ph ac line voltage.


  • Top Cited Papers

    Operation, Control, and Applications of the Modular Multilevel Converter: A Review

    by Suman Debnath, Jiangchao Qin, Behrooz Bahrani, Maryam Saeedifard, Peter Barbosa

    The modular multilevel converter (MMC) has been a subject of increasing importance for medium/high-power energy conversion systems. Over the past few years, significant research has been done to address the technical challenges associated with the operation and control of the MMC. In this paper, a general overview of the basics of operation of the MMC along with its control challenges are discussed, and a review of state-of-the-art control strategies and trends is presented. Finally, the applications of the MMC and their challenges are highlighted.


  • Average Power Balancing Control of a STATCOM Based on the Cascaded H-Bridge PWM Converter With Star Configuration

    by Chia-Tse Lee, Bo-Siang Wang, Sheng-Wan Chen, Shih-Feng Chou, Jun-Lin Huang, Po-Tai Cheng, Hirofumi Akagi, Peter Barbosa

    This paper presents the average power balancing (APB) control method for the modular multilevel cascaded converter based on single-star bridge cells in the static synchronous compensator applications. The proposed control method accomplishes both the reactive power compensation and the dc bus voltage balancing control even under grid voltage sags. The low-voltage ride-through capability of the proposed method will become more and more important as more distributed generation resources are integrated into the grid. Laboratory test results are provided to validate the proposed APB control method.