William A. Baeslack
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
William A. Baeslack has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
K. H. Hou
Ohio State University
5 shared publicationsF. D. Mullins
Materials Laboratory, Air Force Wright Aeronautical Laboratories
4 shared publicationsF. H. Froes
University of Idaho
4 shared publicationsD. Phillips
Edison Welding Institute
3 shared publicationsD. W. Becker
3 shared publicationsD.J Evans
Air Force Research Laboratory, Materials and Manufacturing Directorate, WPAFB, OH 45433, USA
3 shared publications
Latest Publications
- 1 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (2) , 676-679
Orientation relationships and morphology of S phase in friction stir welded Al–Cu–Mg alloy
- 1 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (2) , 676-679
Orientation relationships and morphology of S phase in friction stir welded Al–Cu–Mg alloy
- 1 March 2007
- Published by Elsevier in Scripta Materialia
- Vol. 56 (6) , 513-516
Study of microstructural evolution in friction-stir welded thin-sheet Al–Cu–Li alloy using transmission-electron microscopy
- 1 March 2007
- Published by Elsevier in Scripta Materialia
- Vol. 56 (6) , 513-516
Study of microstructural evolution in friction-stir welded thin-sheet Al–Cu–Li alloy using transmission-electron microscopy
- 21 April 2006
- Published by Springer Nature in Journal of Materials Science
- Vol. 41 (10) , 2939-2951
Structure, properties and fracture of friction stir welds in a high-temperature Al-8.5Fe-1.3V–1.7Si alloy (AA-8009)
- 21 April 2006
- Published by Springer Nature in Journal of Materials Science
- Vol. 41 (10) , 2939-2951
Structure, properties and fracture of friction stir welds in a high-temperature Al-8.5Fe-1.3V–1.7Si alloy (AA-8009)
- 1 May 2004
- Published by Springer Nature in Journal of Materials Research
- Vol. 19 (5) , 1374-1386
Degradation and failure mechanisms in thermally exposed Au–Al ball bonds
During the manufacturing and the service life of Au–Al wire bonded electronic packages, the ball bonds experience elevated temperatures and hence accelerated interdiffusion reactions that promote the transformation of the Au–Al phases and the growth of creep cavities. In the current study, these service conditions were simulated by thermally exposing Au–Al ball bonds at 175 and 250 °C for up to 1000 h. The Au–Al phase transformations and the growth of cavities were characterized by scanning electron microscopy. The volume changes associated with the transformation of the intermetallic phases were theoretically calculated, and the effect of the phase transformations on the growth of cavities was studied. The as-bonded microstructure of a Au–Al ball bond typically consisted of an alloyed zone and a line of discontinuous voids (void line) between the Au bump and the bonded Al metallization. Thermal exposure resulted in the nucleation, growth, and the transformation of the Au–Al phases and the growth of cavities along the void line. Theoretical analysis showed that the phase transformations across and lateral to the ball bond result in significant volumetric shrinkage. The volumetric shrinkage results in tensile stresses and promotes the growth of creep cavities at the void line. Cavity growth is higher at the crack front due to stress concentration, which was initially at the edge of the void line. The crack propagation occurs laterally by the coalescence of sufficiently grown cavities at the void line resulting in the failure of the Au–Al ball bonds.
- 1 May 2004
- Published by Springer Nature in Journal of Materials Research
- Vol. 19 (5) , 1374-1386
Degradation and failure mechanisms in thermally exposed Au–Al ball bonds
During the manufacturing and the service life of Au–Al wire bonded electronic packages, the ball bonds experience elevated temperatures and hence accelerated interdiffusion reactions that promote the transformation of the Au–Al phases and the growth of creep cavities. In the current study, these service conditions were simulated by thermally exposing Au–Al ball bonds at 175 and 250 °C for up to 1000 h. The Au–Al phase transformations and the growth of cavities were characterized by scanning electron microscopy. The volume changes associated with the transformation of the intermetallic phases were theoretically calculated, and the effect of the phase transformations on the growth of cavities was studied. The as-bonded microstructure of a Au–Al ball bond typically consisted of an alloyed zone and a line of discontinuous voids (void line) between the Au bump and the bonded Al metallization. Thermal exposure resulted in the nucleation, growth, and the transformation of the Au–Al phases and the growth of cavities along the void line. Theoretical analysis showed that the phase transformations across and lateral to the ball bond result in significant volumetric shrinkage. The volumetric shrinkage results in tensile stresses and promotes the growth of creep cavities at the void line. Cavity growth is higher at the crack front due to stress concentration, which was initially at the edge of the void line. The crack propagation occurs laterally by the coalescence of sufficiently grown cavities at the void line resulting in the failure of the Au–Al ball bonds.
- 1 April 2004
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 33 (4) , 340-352
Phase transformations in thermally exposed Au-Al ball bonds
- 1 April 2004
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 33 (4) , 340-352
Phase transformations in thermally exposed Au-Al ball bonds
- 1 April 2004
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 35 (4) , 1273-1280
Partial diffusion reactions and the associated volume changes in thermally exposed Au-Al ball bonds
- 1 April 2004
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 35 (4) , 1273-1280
Partial diffusion reactions and the associated volume changes in thermally exposed Au-Al ball bonds
- 1 March 2003
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 344 (1-2) , 300-311
Effect of long term aging on the microstructural stability and mechanical properties of Ti–6Al–2Cr–2Mo–2Sn–2Zr alloy
- 1 March 2003
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 344 (1-2) , 300-311
Effect of long term aging on the microstructural stability and mechanical properties of Ti–6Al–2Cr–2Mo–2Sn–2Zr alloy
- 1 February 2003
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 343 (1-2) , 210-226
Effect of heat treatment and silicon addition on the microstructure development of Ti–6Al–2Cr–2Mo–2Sn–2Zr alloy
- 1 February 2003
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 343 (1-2) , 210-226
Effect of heat treatment and silicon addition on the microstructure development of Ti–6Al–2Cr–2Mo–2Sn–2Zr alloy
- 1 August 1999
- Published by Elsevier in Scripta Materialia
- Vol. 41 (6) , 659-665
On the stability of ω phase in Ti-6-22-22S and Ti-6-4 alloys
- 1 August 1999
- Published by Elsevier in Scripta Materialia
- Vol. 41 (6) , 659-665
On the stability of ω phase in Ti-6-22-22S and Ti-6-4 alloys
- 1 August 1998
- Published by Elsevier in Acta Materialia
- Vol. 46 (13) , 4485-4495
Precipitation of ordered α2 phase in Ti–6–22–22 alloy
- 1 August 1998
- Published by Elsevier in Acta Materialia
- Vol. 46 (13) , 4485-4495
Precipitation of ordered α2 phase in Ti–6–22–22 alloy