YMYevhenii O. Modlo

Yevhenii O. Modlo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yevhenii O. Modlo has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Device for Slip Control of the Rolls of the Crimping Mill

    by Viacheslav Khyzhniak, Oleksandr Lytovchenko, Yuliia Lytovchenko, Yevhenii Modlo, Mykola Zhukov

  • Development of a Software Tool for Implementing an Algorithm for Solving a Two-Factor Transportation Problem with Weighting Coefficients

    by Maksym O. Chyzhmotria, Oleksii V. Chyzhmotria, Tetiana A. Vakaliuk, Iryna S. Mintii, Yevhenii O. Modlo

  • Open Access

    Method for representing the electromechanical characteristics of an electric traction drive with sequentially excited DC motors

    by Andrii Pyrozhenko, Yevhenii Modlo, Viacheslav Khyzhniak, Yuliia Lytovchenko, Oleksandr Lytovchenko

    The shortcomings that occur during the construction of the electromechanical characteristics of a traction electric drive with DC motors of series excitation are presented. An analysis of known methods of constructing the specified electromechanical characteristics is carried out, such as by universal characteristic, by known catalog data of the engine. Based on the analysis, a number of shortcomings of known methods of constructing the electromechanical characteristics of a traction electric drive with DC motors of series excitation and their inconsistency with existing requirements are revealed. The dependence of the magnetic flux of DC motors with series excitation on the load on the shaft is the cause of the nonlinearity of their electromechanical characteristics. Factories - manufacturers of such engines provide experimentally obtained universal characteristics (expressed in relative units). Using them, it is possible to construct a universal mechanical characteristic, from which it is possible to proceed to the characteristics of the selected engine. To do this, it is necessary to multiply the values I, M and ω laid out along the axes by their nominal values. In this case, it is usually necessary to change the scale grid of the graph, since the previous one will correspond to the fractional value of the quantities plotted on the axes. The presented method of constructing electromechanical characteristics according to the universal characteristic has an error of up to 30%, which is associated both with the nonlinearity of the electromechanical characteristics of DC motors with series excitation, and with the need for a graphic transition from the universal characteristic to the characteristic of a specific traction motor. The method of constructing electromechanical characteristics according to catalog data has similar disadvantages. A method of constructing electromechanical characteristics analytically is proposed, which allows avoiding the disadvantages.

  • Open Access

    Digital measurement of shaft rotation speed based on encoder signal: error analysis and adaptive method

    by Oleksandr Lytovchenko, Yuliia Lytovchenko, Viacheslav Khyzhniak, Yevhenii Modlo

    The article analyzes the errors of digital measurement of speed (DVS) of rotation of the electric drive shaft using the signal of the angle sensor (AOS), which is part of the encoder, since in modern process automation systems (AUS TP) two different measuring devices are traditionally used to control the position and speed of rotation of the drive motor shaft: an encoder and a tachogenerator. The aim of the work is to develop an adaptive method for digital measurement of shaft rotation speed with reduced methodological error based on the existing encoder. The essence of the method is to count the number of pulses of a highly stable clock generator (timer) during one signal period. The methodological and dynamic components of the error are considered, their analytical dependencies and the results of numerical modeling for low-speed and high-speed mechanisms of metallurgical production are given. A method for reducing methodological error by increasing the measurement base is proposed and tested. The implementation of an economical DCS system based on a 16-bit microcontroller is shown, which provides a combination of position and speed measurement functions in a single sensor and eliminates the need to use a tachogenerator. The cost of the proposed solution is 6-7 times lower than the cost of a traditional scheme using a tachogenerator, since the indicated cost of the proposed solution is about 450 UAH (microcontroller and minimal wiring), which is significantly lower than the cost of an industrial tachogenerator (from 3000 UAH). The exclusion of the tachogenerator also simplifies installation, reduces the dimensions of the control cabinet and increases the reliability of the system by reducing the number of components.

  • Open Access

    DAC with 50 Hz AC voltage output, errors and operating algorithms

    by Viacheslav Khyzhniak, Yevhenii Modlo, Yuliia Lytovchenko, Oleksandr Lytovchenko, Andrii Pyrozhenko

    The article investigates the basic principles of operation of a 10-bit digital-to-analog converter (DAC) for generating an alternating voltage with a frequency of 50 Hz. The sources of errors that arise during the operation of the DAC are considered, including the discreteness of the output signal, inaccuracies of the generation algorithm and the influence of the load. In particular, the methodological error, which is 0.015%, and the frequency error, which reaches 0.5 Hz, are analyzed. This indicates that the developed system meets modern standards of accuracy and stability of signals. As an example, a digital-to-analog converter with the following characteristics is used: bit capacity - 10 bits, speed - no more than 25 μs, output voltage - ±10 V, discharge capacity - 10 mV, error - 0.01%, load resistance - 510 Ohm, the period of the timer pulses in the controller where the DAC is located is 1 μs. The article presents a digital interpolation algorithm that allows to reduce errors at the output and improve the quality of the sinusoidal signal. The procedure for timer synchronization and output signal generation based on numerical calculations is described in detail. Particular attention is paid to minimizing the so-called "jamminess" of the sinusoidal wave in the area of its passage through zero. This is achieved by introducing an auxiliary voltage shift, which allows to ensure a smooth transition between signal levels. A significant part of the work is devoted to the use of analog filtering and digital interpolation to improve the shape of the output signal. Such methods allow to significantly reduce distortion and ensure high accuracy of voltage reproduction even with significant load changes. In addition, the authors of the article offer an optimized table of signal generation steps, which allows to reduce calculation time and improve the energy efficiency of the system. The practical results of the article have wide application in the field of electronics, including the development of automatic control systems, measuring equipment, as well as in the field of electric power. The obtained data can be used for both industrial and educational purposes, for training future specialists.

  • Quantum enhanced machine learning: An overview

    by Pavlo V. Zahorodko, Yevhenii O. Modlo, Olga O. Kalinichenko, Tetiana V. Selivanova, Serhiy O. Semerikov

    Machine learning is now widely used almost everywhere, primarily for forecasting. The main idea of the work is to identify the possibility of achieving a quantum advantage when solving machine learning problems on a quantum computer.

  • WebAR development tools: An overview

    by Dmytro S. Shepiliev, Yevhenii O. Modlo, Yuliia V. Yechkalo, Viktoriia V. Tkachuk, Mykhailo M. Mintii, Iryna S. Mintii, Oksana M. Markova, Tetiana V. Selivanova, Olena M. Drashko, Olga O. Kalinichenko, et al.

    Web augmented reality (WebAR) development tools aimed at improving the visual aspects of learning are far from being visual and available themselves. This causing problems of selecting and testing WebAR development tools for CS undergraduates mastering in web-design basics. The research is aimed at conducting comparative analysis of WebAR tools to select those appropriated for beginners.

  • Open Access

    The Use of Mobile Internet Devices in Teaching Bachelors of Electromechanics Modeling of Technical Objects

    by Yevhenii Modlo, Ruslan Shaida, Oleksandr Lytovchenko

  • Virtual Chemical Laboratories as a Tools of Supporting the Learning Research Activity of Students in Chemistry While Studying the Topic "Solutions"

    by Pavlo Nechypurenko, Olha Evangelist, Tetiana Selivanova, Yevhenii Modlo

    The article discusses the importance of student research activities for the effective formation of the key competencies of a future specialist in the field of chemistry. The theme “Solutions” is defined as one of the most important in the school chemistry course and at the same time as the most suitable for the implementation of educational research activity of students. To support students’ research activities, two types of virtual chemical laboratories are used: distance and imitation. The combination of these types of virtual chemical laboratories in the study of the topic “Solutions” provides an opportunity to take advantage of each of them and increase the level of support for educational and research activities of students. The conditions and ways of using virtual chemical laboratories to provide students with research activities when studying the topic “Solutions” are examined. Examples of developed virtual chemical works and their essence are given. Based on the implementation of virtual chemical laboratories in the educational process of various educational institutions, it is justified the assumption about the effectiveness of using the developed virtual chemical research to develop students’ research activities when studying the topic “Solutions”.

  • Methods of using mobile Internet devices in the formation of the general professional component of bachelor in electromechanics competency in modeling of technical objects

    by Yevhenii O. Modlo, Serhiy O. Semerikov, Ruslan P. Shajda, Stanislav T. Tolmachev, Oksana M. Markova, Pavlo P. Nechypurenko, Tetiana V. Selivanova

    The article describes the components of methods of using mobile Internet devices in the formation of the general professional component of bachelor in electromechanics competency in modeling of technical objects: using various methods of representing models; solving professional problems using ICT; competence in electric machines and critical thinking. On the content of learning academic disciplines “Higher mathematics”, “Automatic control theory”, “Modeling of electromechanical systems”, “Electrical machines” features of use are disclosed for Scilab, SageCell, Google Sheets, Xcos on Cloud in the formation of the general professional component of bachelor in electromechanics competency in modeling of technical objects. It is concluded that it is advisable to use the following software for mobile Internet devices: a cloud-based spreadsheets as modeling tools (including neural networks), a visual modeling systems as a means of structural modeling of technical objects; a mobile computer mathematical system used at all stages of modeling; a mobile communication tools for organizing joint modeling activities.