TMToshiyuki Mihara

Toshiyuki Mihara

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Toshiyuki Mihara has a total of 84 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhancement of photoluminescence of glass phosphor by nanoimprint of moth-eye structure

    by Kenji Shinozaki, Ryosuke Kamakura, Shunsuke Murai, Toshiyuki Mihara, Naoyuki Kitamura, Yuki Kawachiya, Katsuhisa Tanaka, Tomoko Akai

    We demonstrated that a moth-eye surface pattern on the luminous inorganic glass could enhance the photoluminescence (PL) intensity notably. A moth-eye pattern of a square array of cones at pitch of 250 nm was fabricated on Eu3+-doped MgF2–MgO–BaO–B2O3 glass by thermal nanoimprinting at 520°C. A simulation with rigorous coupled-wave analysis demonstrated that the surface structure could reduce the surface reflectance in the optical input for the excitation wavelength λ of 405 nm, i.e., −1.1% for p-polarized light, 10.6% for s-polarized light, and 4.1% for non-polarized light in total of a half round angle for the irradiation from a surface light source. The angularly dependent PL of the excitation angle on the nanoimprinted glass was measured by an excitation of UV laser diode (λ = 405 nm). The enhancements of ∼0% for p-polarized light and ∼9% for s-polarized light were observed at the incident angle = 5°.


  • Fabrication and evaluation of active spectral filter with metal-insulator-metal structure for visible light communication

    by Kensuke Murai, Yasushi Oshikane, Fumihiko Yamamoto, Kou Hattori, Shoichi Mochizuki, Toshiyuki Mihara, Motohiro Nakano

    Plasmonic spectral filter based on a metal-insulator-metal (MIM) structure is one of the candidates of active devices with white LEDs in the ubiquitous network society. In order to make this filter electrically active, “silver alloy and quartz-coated silver films” and “PLZT films by the dry and wet processes” were fabricated and evaluated under high annealing temperatures. The quartz-coated silver film and the PLZT film by the dry process” could be possible as the metal and insulator layers, respectively. The issue of thickness determination of the insulator layer is also discussed.

  • Pattern transfer of nanostructures onto glass using nanoimprint films

    by Chia-Lung Lee, Toshiyuki Mihara, Masaru Yamashita, Tomoko Akai

  • Power Generation of a p ‐Type Ca 3 Co 4 O 9 / n ‐Type CaMnO 3 Module

    by Saori Urata, Ryoji Funahashi, Toshiyuka Mihara, Atsuko Kosuga, Satoshi Sodeoka, Takahiro Tanaka

    Thermoelectric modules composed of eight pairs of p ‐type Ca 2.7 Bi 0.3 Co 4 O 9 (Co‐349) and n ‐type CaMn 0.98 Mo 0.02 O 3 (Mn‐113) bulks were constructed using Ag electrodes and paste including powder of the n ‐type oxide. The former bulks were prepared by hot pressing. On the other hand, the latter were densified using a cold isostatic pressing technique and sintered in atmospheric pressure. Dimensions of both oxide legs were 5 mm wide and thick and 4.5 mm high. An alumina plate was used as a substrate, and there was no alumina plate on the other side of the modules. When the substrate side was heated, the module could generate up to 1.0 V and 0.17 W of open circuit voltage ( V O ) and maximum power ( P max ), respectively, at a hot‐side temperature of 1273 K (furnace temperature as a heat source) and a cold‐side temperature of 298 K (circulated water temperature) in air. But internal resistance R I reached a value of 1.5 Ω, which is about six times higher than the calculated one from resistivity of both p ‐ and n ‐type bulks. When the substrate side was cooled, V O and P max reached 0.7 V and 0.34 W of V O and P max , respectively, at a furnace temperature of 1273 K.


  • Mechanical properties of oxide materials

    by S. Urata, R. Funahashi, T. Mihara, A. Kosuga, N. Miyasou

    Thermoelectric modules composed of eight pairs of p-type Ca3Co4O9 (Co-349) and n-type CaMnO3 (Mn-113) or LaNiO3 (Ni-113) bulks were constructed using Ag electrodes, paste, and alumina substrate. In these modules, it was reported that after power generation at 1273K of the hot side heater temperature the Mn-113 legs were broken near the alumina substrate. To make the mechanism of the destruction clear, coefficient of thermal expansion (CTE), three-point bending strength, and microstructure were investigated. The CTE of the Co-349 and Ni-113 bulks is closer than that of the Mn-113 one to the alumina substrate. The three-point bending strength of the Co-349 and Ni-113 bulks are higher than that of Mn-113 one. These are the reasons of the destruction of the Mn-113 legs near the alumina substrate in the modules by heating. Lower relative density of the Mn-113 bulks than the other oxide ones leads low bending strength. The Mn-113 grains, moreover, are grown much more than other oxides. This allows cracks to run easily in the Mn-113 bulks. The stronger bending strength, thermal expansion closer to the substrate, higher relative density, and smaller grains for the Ni-113 and Co-349 bulks than those for the Mn-113 bulks are the reasons of destruction of the latter bulks.

  • Thermoelectrical properties of A-site substituted Ca1−xRexMnO3 system

    by D. Flahaut, T. Mihara, R. Funahashi, N. Nabeshima, K. Lee, H. Ohta, K. Koumoto

    CaMnO3 is an electron-doped compound which belongs to the perovskite family. Despite its high Seebeck coefficient S value, the figure of merit at high temperature remains low due to its large resistivity ρ(ρ300K=2Ωcm) . To optimize the performance of this material in terms of thermoelectric properties, several substitutions have been attempted on the Ca site to decrease the ρ . Structure and thermoelectric properties of polycrystalline samples Ca1−xAxMnO3 (A=Yb , Tb, Nd, and Ho) have been investigated. Although ρ strongly depends on the ionic radius ⟨rA⟩ and carrier concentration, we have shown that the thermal conductivity κ is mainly driven by the atomic weight of the A site and decreases with it. Therefore, it seems that the S , ρ , and κ could be controlled separately. For instance, the highest dimensionless ZT (=0.16) has been obtained at 1000K in the air for Ca0.9Yb0.1MnO3 .


  • Fabrication of Oxide Thermoelectric Module Consisting of Multi-Layered Thick Films

    by S. Horii, M. Sakurai, T. Okamoto, J. Shimoyama, K. Kishio, T. Uchikoshi, T.S. Suzuki, Y. Sakka, R. Funahashi, T. Mihara

    We report the fabrication and thermoelectric properties of a multi-layered unicouple of [Ca2CoO3-delta]0.62CoO2 (Ca349; p-type) and Ca0.9La0.1MnO3-delta (Mn113; n-type). The multi-layered thick films consisting of Ca349, Mn113 and Al2O3 were prepared using an electrophoretic deposition (EPD) method. In particular, the Ca349 layer was deposited under a magnetic field of 3 T and strongly c-axis-grain-oriented microstructure was obtained. The unicouple of hot-forged Ca349 and Mn113 layers generated 85 mV of voltage in DeltaT ~450 K and, however, showed remarkably high internal resistance due to porous microstructure of the Mn113 layer. The development of a densification process for the n-type layer is an important for improving higher power density


  • Preparation of p-type materials thin-film by using buffer layer

    by D. Flahaut, T. Mihara, R. Funahashi

    c-axis oriented Ca2.7Bi0.3Co4O 9 thin films have been grown on glass substrate. Deposition with a buffer-layer has also been attempted. Two orientations of the CeO 2 buffer layer can be obtained, (111) and (100) depending on deposition conditions. 349 phase is well grown on the buffer layer but no peaks are detected on X-Ray patterns. T Seebeck coefficient of the 349 phase reaches -60muV.K-1 but the resistivity remains high

  • A portable thermoelectric-power-generating module composed of oxide devices

    by R. Funahashi, M. Mikami, T. Mihara, S. Urata, N. Ando

    High power density is a strong point of thermoelectric generation. Exploitation of this salient characteristic would make thermoelectric modules promising candidates for mobile power applications. Here we show how power can be generated using a small thermoelectric module composed of 140 pairs of oxide thermoelectric unicouples. The module weighs 19.8g and its dimensions are 53mm long, 32mm wide, and 5.0mm thick. The hot-pressed thermoelectric oxide bulk materials used were connected with a Ag paste, incorporating oxide powder, and Ag electrodes. The module’s open circuit voltage increases with increasing hot-side temperature (TH) and reaches 4.5V at a TH of 1072K in air. No deterioration in output power was seen when power generation was carried out ten times at a TH of 723K with intermediate cooling to room temperature. The module was successfully used to charge a lithium-ion battery in a mobile phone.


  • OS4-9 Development of a heat exchangeable thermoelectric module

    by Ryoji Funahashi, Saori Urata, Toshiyuki Mihara, Kanako Iwasaki, Yoshinori Hisazumi, Akeshi Kegasa