Antti Kemppinen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Antti Kemppinen has a total of 122 co-authors. Here are the top co-authors by number of shared publications:
- Emma Mykkänen
VTT Technical Research Centre of Finland
11 shared publications J. P. Pekola
Low Temperature Laboratory, Department of Applied Physics, Aalto University School of Science, PO Box 13500, Aalto 00076, Finland
9 shared publications- Antti Juhani Manninen
Centre for Metrology and Accreditation (MIKES), Espoo, Finland
8 shared publications - Janne Samuel Lehtinen
VTT Technical Research Centre of Finland
8 shared publications - Mikko Möttönen
Aalto University
6 shared publications - Mika Prunnila
VTT Technical Research Centre of Finland
5 shared publications
Latest Publications
- Open Access
- 19 August 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (17) , 6770-6781
Atomic Layer Deposition of Superconductive Niobium Carbonitride Thin Films
Transition metal carbonitrides (TMCN) are stable materials with excellent catalytic and superconductive properties. Atomic layer deposition (ALD) stands out as the optimal method for the fabrication of these materials, enabling their use in future applications. In this study, we deposit ALD NbC x N y films at 250–450 °C with NbF5 and 1,4-bis(trimethylsilyl)–1,4-dihydropyrazine on Si, Ru, TiN, and soda lime glass. We analyze the film growth characteristics, composition, and phase. The films show substrate-enhanced growth on Si with a growth per cycle (GPC) of 1.3 Å. Additionally, the films were superconductive as-deposited and had a superconducting critical temperature (T c ) of 14.5 K after annealing at 950 °C. This work expands the range of TMCNs deposited by ALD and demonstrates the applicability of ALD for thin film materials with a high T c .
- 19 August 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (17) , 6770-6781
Open AccessAtomic Layer Deposition of Superconductive Niobium Carbonitride Thin Films
Transition metal carbonitrides (TMCN) are stable materials with excellent catalytic and superconductive properties. Atomic layer deposition (ALD) stands out as the optimal method for the fabrication of these materials, enabling their use in future applications. In this study, we deposit ALD NbC x N y films at 250–450 °C with NbF5 and 1,4-bis(trimethylsilyl)–1,4-dihydropyrazine on Si, Ru, TiN, and soda lime glass. We analyze the film growth characteristics, composition, and phase. The films show substrate-enhanced growth on Si with a growth per cycle (GPC) of 1.3 Å. Additionally, the films were superconductive as-deposited and had a superconducting critical temperature (T c ) of 14.5 K after annealing at 950 °C. This work expands the range of TMCNs deposited by ALD and demonstrates the applicability of ALD for thin film materials with a high T c .
- 13 December 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (6)
Efficient electronic cooling by niobium-based superconducting tunnel junctions
- 13 December 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (6)
Efficient electronic cooling by niobium-based superconducting tunnel junctions
- Open Access
- 1 July 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (7)
Effect of ion irradiation on superconducting thin films
We demonstrate ion irradiation by argon or gallium as a wafer-scale post-processing method to increase disorder in superconducting thin films. We study several widely used superconductors, both single-elements and compounds. We show that ion irradiation increases normal-state resistivity in all our films, which is expected to enable tuning their superconducting properties, for example, toward a higher kinetic inductance. We observe an increase in superconducting transition temperature for Al and MoSi and a decrease for Nb, NbN, and TiN. In MoSi, ion irradiation also improves the mixing of the two materials. We demonstrate the fabrication of an amorphous and homogeneous film of MoSi with uniform thickness, which is promising, for example, for superconducting nanowire single-photon detectors.
- 1 July 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (7)
Open AccessEffect of ion irradiation on superconducting thin films
We demonstrate ion irradiation by argon or gallium as a wafer-scale post-processing method to increase disorder in superconducting thin films. We study several widely used superconductors, both single-elements and compounds. We show that ion irradiation increases normal-state resistivity in all our films, which is expected to enable tuning their superconducting properties, for example, toward a higher kinetic inductance. We observe an increase in superconducting transition temperature for Al and MoSi and a decrease for Nb, NbN, and TiN. In MoSi, ion irradiation also improves the mixing of the two materials. We demonstrate the fabrication of an amorphous and homogeneous film of MoSi with uniform thickness, which is promising, for example, for superconducting nanowire single-photon detectors.
- Open Access
- 9 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (15)
Thermal resistance in superconducting flip-chip assemblies
Cryogenic microsystems that utilize different 3D integration techniques are being actively developed, e.g., for the needs of quantum technologies. 3D integration can introduce opportunities and challenges to the thermal management of low temperature devices. In this work, we investigate sub-1 K inter-chip thermal resistance of a flip-chip bonded assembly, where two silicon chips are interconnected by compression bonding via indium bumps. The total thermal contact area between the chips is 0.306 mm2, and we find that the temperature dependence of the inter-chip thermal resistance follows the power law of αT−3, with α=7.7–15.4 K4μm2/nW. The T−3 relation indicates phononic interfacial thermal resistance, which is supported by the vanishing contribution of the electrons to the thermal conduction, due to the superconducting interconnections. Such a thermal resistance value can introduce a thermalization bottleneck in particular at cryogenic temperatures. This can be detrimental for some applications, yet it can also be harnessed. We provide an example of both cases by estimating the parasitic overheating of a cryogenic flip-chip assembly operated under various heat loads as well as simulate the performance of solid-state junction microrefrigerators utilizing the observed thermal isolation.
- 9 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (15)
Open AccessThermal resistance in superconducting flip-chip assemblies
Cryogenic microsystems that utilize different 3D integration techniques are being actively developed, e.g., for the needs of quantum technologies. 3D integration can introduce opportunities and challenges to the thermal management of low temperature devices. In this work, we investigate sub-1 K inter-chip thermal resistance of a flip-chip bonded assembly, where two silicon chips are interconnected by compression bonding via indium bumps. The total thermal contact area between the chips is 0.306 mm2, and we find that the temperature dependence of the inter-chip thermal resistance follows the power law of αT−3, with α=7.7–15.4 K4μm2/nW. The T−3 relation indicates phononic interfacial thermal resistance, which is supported by the vanishing contribution of the electrons to the thermal conduction, due to the superconducting interconnections. Such a thermal resistance value can introduce a thermalization bottleneck in particular at cryogenic temperatures. This can be detrimental for some applications, yet it can also be harnessed. We provide an example of both cases by estimating the parasitic overheating of a cryogenic flip-chip assembly operated under various heat loads as well as simulate the performance of solid-state junction microrefrigerators utilizing the observed thermal isolation.
- 2 August 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (5) , 052603
Cascaded superconducting junction refrigerators: Optimization and performance limits
We demonstrate highly transparent silicon–vanadium and silicon–aluminum tunnel junctions with relatively low sub-gap leakage current and discuss how a trade-off typically encountered between transparency and leakage affects their refrigeration performance. We theoretically investigate cascaded superconducting tunnel junction refrigerators with two or more refrigeration stages. In particular, we develop an approximate method that takes into account self-heating effects but still allows us to optimize the cascade a single stage at a time. We design a cascade consisting of energy-efficient refrigeration stages, which makes cooling of, e.g., quantum devices from above 1 K to below 100 mK a realistic experimental target.
- 2 August 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (5) , 052603
Cascaded superconducting junction refrigerators: Optimization and performance limits
We demonstrate highly transparent silicon–vanadium and silicon–aluminum tunnel junctions with relatively low sub-gap leakage current and discuss how a trade-off typically encountered between transparency and leakage affects their refrigeration performance. We theoretically investigate cascaded superconducting tunnel junction refrigerators with two or more refrigeration stages. In particular, we develop an approximate method that takes into account self-heating effects but still allows us to optimize the cascade a single stage at a time. We design a cascade consisting of energy-efficient refrigeration stages, which makes cooling of, e.g., quantum devices from above 1 K to below 100 mK a realistic experimental target.
- Open Access
- 19 July 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (3) , 032601
Driving a low critical current Josephson junction array with a mode-locked laser
We report proof-of-concept experiments on an optically driven Josephson voltage standard based on a mode-locked laser (MLL), a time-division multiplexer, and a cryogenic ultrafast photodiode driving an overdamped Josephson junction array (JJA). Our optical pulse pattern generator (PPG) concept builds on the capability of MLLs to produce trains of picosecond-wide optical pulses with little amplitude and temporal spread. Our present setup enables multiplication of the original 2.3 GHz pulse repetition frequency by a factor of 8. A commercial photodiode converts the optical pulses into about 25 ps wide electrical pulses in liquid helium several cm from the JJA. Using a custom-made MLL, we can drive a JJA with a low critical current of 360 μA at multiple Shapiro steps. We have performed experiments with pulse pairs whose time interval can be set freely without distorting the shapes of individual pulses. Experimental results are in qualitative agreement with theoretical simulations, and they demonstrate, e.g., crossover in the Shapiro step pattern when the time interval between the pulses is approximately equal to the inverse of the characteristic frequency of the JJA. However, there are quantitative discrepancies, which motivate an improved integration of photodiodes and JJAs to improve both the understanding and fidelity of Josephson Arbitrary Waveform Synthesizers. Considering future quantum technologies in a wider perspective, our optical approach is a potential enabler for fast and energy-efficient pulse drive without an expensive high-bandwidth electrical PPG and without high-bandwidth electrical cables that yield too high thermal conductance between cryogenic and room temperatures.
- 19 July 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (3) , 032601
Open AccessDriving a low critical current Josephson junction array with a mode-locked laser
We report proof-of-concept experiments on an optically driven Josephson voltage standard based on a mode-locked laser (MLL), a time-division multiplexer, and a cryogenic ultrafast photodiode driving an overdamped Josephson junction array (JJA). Our optical pulse pattern generator (PPG) concept builds on the capability of MLLs to produce trains of picosecond-wide optical pulses with little amplitude and temporal spread. Our present setup enables multiplication of the original 2.3 GHz pulse repetition frequency by a factor of 8. A commercial photodiode converts the optical pulses into about 25 ps wide electrical pulses in liquid helium several cm from the JJA. Using a custom-made MLL, we can drive a JJA with a low critical current of 360 μA at multiple Shapiro steps. We have performed experiments with pulse pairs whose time interval can be set freely without distorting the shapes of individual pulses. Experimental results are in qualitative agreement with theoretical simulations, and they demonstrate, e.g., crossover in the Shapiro step pattern when the time interval between the pulses is approximately equal to the inverse of the characteristic frequency of the JJA. However, there are quantitative discrepancies, which motivate an improved integration of photodiodes and JJAs to improve both the understanding and fidelity of Josephson Arbitrary Waveform Synthesizers. Considering future quantum technologies in a wider perspective, our optical approach is a potential enabler for fast and energy-efficient pulse drive without an expensive high-bandwidth electrical PPG and without high-bandwidth electrical cables that yield too high thermal conductance between cryogenic and room temperatures.
- Open Access
- 10 April 2020
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 6 (15) , eaax9191
Thermionic junction devices utilizing phonon blocking
Controlling electron and phonon flows through a solid junction enables novel on-chip cooling and sensing functionalities.
- 10 April 2020
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 6 (15) , eaax9191
Open AccessThermionic junction devices utilizing phonon blocking
Controlling electron and phonon flows through a solid junction enables novel on-chip cooling and sensing functionalities.
- 19 March 2020
- Published by IOP Publishing in Metrologia
- Vol. 57 (2) , 025013
Realisation of a quantum current standard at liquid helium temperature with sub-ppm reproducibility
A silicon electron pump operating at the temperature of liquid helium has demonstrated repeatable operation with sub-ppm accuracy. The pump current, approximately 168 pA, is measured by three laboratories, and the measurements agree with the expected current ef within the uncertainties which range from 0.2 ppm to 1.3 ppm. All the measurements are carried out in zero applied magnetic field, and the pump drive signal is a sine wave. The combination of simple operating conditions with high accuracy demonstrates the possibility that an electron pump can operate as a current standard in a National Measurement Institute. We also discuss other practical aspects of using the electron pump as a current standard, such as testing its robustness to changes in the control parameters, and using a rapid tuning procedure to locate the optimal operation point.
- 19 March 2020
- Published by IOP Publishing in Metrologia
- Vol. 57 (2) , 025013
Realisation of a quantum current standard at liquid helium temperature with sub-ppm reproducibility
A silicon electron pump operating at the temperature of liquid helium has demonstrated repeatable operation with sub-ppm accuracy. The pump current, approximately 168 pA, is measured by three laboratories, and the measurements agree with the expected current ef within the uncertainties which range from 0.2 ppm to 1.3 ppm. All the measurements are carried out in zero applied magnetic field, and the pump drive signal is a sine wave. The combination of simple operating conditions with high accuracy demonstrates the possibility that an electron pump can operate as a current standard in a National Measurement Institute. We also discuss other practical aspects of using the electron pump as a current standard, such as testing its robustness to changes in the control parameters, and using a rapid tuning procedure to locate the optimal operation point.
- 1 November 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 31 (1) , 015002
Superconducting MoSi nanowires
We have fabricated disordered superconducting nanowires of molybdenium silicide. A molybdenium nanowire is first deposited on top of silicon, and the alloy is formed by rapid thermal annealing. The method allows tuning of the crystal growth to optimize e.g. the resistivity of the alloy for potential applications in quantum phase slip (QPS) devices and superconducting nanowire single-photon detectors. The wires have effective diameters from 42 to 79 nm, enabling the observation of crossover from conventional superconductivity to regimes affected by thermal and quantum fluctuations. In the smallest diameter wire and at temperatures well below the superconducting critical temperature, we observe residual resistance and negative magnetoresistance, which can be considered as fingerprints of QPSs.
- 1 November 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 31 (1) , 015002
Superconducting MoSi nanowires
We have fabricated disordered superconducting nanowires of molybdenium silicide. A molybdenium nanowire is first deposited on top of silicon, and the alloy is formed by rapid thermal annealing. The method allows tuning of the crystal growth to optimize e.g. the resistivity of the alloy for potential applications in quantum phase slip (QPS) devices and superconducting nanowire single-photon detectors. The wires have effective diameters from 42 to 79 nm, enabling the observation of crossover from conventional superconductivity to regimes affected by thermal and quantum fluctuations. In the smallest diameter wire and at temperatures well below the superconducting critical temperature, we observe residual resistance and negative magnetoresistance, which can be considered as fingerprints of QPSs.
- 27 March 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (5) , 055006
Characterizing superconducting filters using residual microwave background
A normal metal–superconductor hybrid single-electron trap with tunable barrier is utilized as a tool for spectrum analysis at the extremely low signal levels, using only well filtered cryogenic microwave background as a photon source in the frequency range from about 50 to 210 GHz. We probe millimeter wave propagation in two superconducting systems: a Josephson junction array around its plasma frequency, and a superconducting titanium film in the limit when the photon energies are larger than the superconducting energy gap. This regime is relevant for improving the performance of cryogenic quantum devices but is hard to access with conventional techniques. We show that relatively simple models can be used to describe the essential properties of the studied components.
- 27 March 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (5) , 055006
Characterizing superconducting filters using residual microwave background
A normal metal–superconductor hybrid single-electron trap with tunable barrier is utilized as a tool for spectrum analysis at the extremely low signal levels, using only well filtered cryogenic microwave background as a photon source in the frequency range from about 50 to 210 GHz. We probe millimeter wave propagation in two superconducting systems: a Josephson junction array around its plasma frequency, and a superconducting titanium film in the limit when the photon energies are larger than the superconducting energy gap. This regime is relevant for improving the performance of cryogenic quantum devices but is hard to access with conventional techniques. We show that relatively simple models can be used to describe the essential properties of the studied components.