May Samir Saleh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
May Samir Saleh has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hayder A. Hasan
Department of Water Resources Engineering, College of Engineering, Mustansiriyah University, Baghdad 10047, Iraq
2 shared publications - Sadiq S. Muhsun
Water Resources Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
2 shared publications - Sahar Al-Khyat
Water Resources Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
2 shared publications - Sherien Fadhel
Faculty of Engineering, Mustansiriyah University, Baghdad 10045, Baghdad, Iraq
2 shared publications - Zuhair Abd Hacheem
Department of Water Resources Engineering, College of Engineering, Mustansiriyah University, Baghdad 10047, Iraq
2 shared publications - Abdul Sahib T. Al Madhhachi
Department of Water Resources Engineering, College of Engineering, Mustansiriyah University, Baghdad, Iraq
1 shared publication
Latest Publications
- Open Access
- 12 May 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (5) , 196
Modeling of Sediment Accumulation Upstream of Samarra Barrage and Assessment of Flushing Efficiency
Sediment accumulates behind dams, thereby reducing their operational efficiency. In response to this issue, hydraulic flushing is considered an effective solution for its removal. A numerical model is used to provide a deep understanding of this process and its dynamics. It acts as a low-cost virtual laboratory that eliminates the need for costly field experiments and provides a precise understanding of sedimentation and flushing behavior. This study used numerical modeling to examine sediment deposition in the Tigris River upstream of the Samarra Barrage. Within the iRIC framework, two models were used: NaysCUBE and Nays2DH. NaysCUBE is a three-dimensional solver that provides detailed simulations of partial gate openings and vertical flow distribution. This capability is crucial for a realistic analysis of the flushing process. Nays2DH is a two-dimensional solver that simulates full gate openings and captures general flow patterns. Results showed that sediment deposits were mostly concentrated within the first kilometer upstream of the dam, particularly when backwater effects caused the outflow to be lower than the inflow. Different gate operation schemes produced varied results: some configurations improved the balance between sediment movement and water flow, whereas others caused local erosion and uneven scouring. Results showed that lowering the water level at the barrage by 1 m increases shear stress on the riverbed by up to 25%, thereby improving the river’s ability to carry sediment without the need for additional discharge. High-discharge flushing operations are no longer feasible because of the reduced flow in the Tigris River since the operation of the Ilisu Dam in Turkey. This study recommends maintaining low water levels at the barrage with frequent and reasonable maintenance operations by partially opening the gates (40–60%). This strategy maintains a balance between the required water storage and sediment control, thereby ensuring the long-term sustainability of the hydraulic structure and the river ecosystem.
- 12 May 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (5) , 196
Open AccessModeling of Sediment Accumulation Upstream of Samarra Barrage and Assessment of Flushing Efficiency
Sediment accumulates behind dams, thereby reducing their operational efficiency. In response to this issue, hydraulic flushing is considered an effective solution for its removal. A numerical model is used to provide a deep understanding of this process and its dynamics. It acts as a low-cost virtual laboratory that eliminates the need for costly field experiments and provides a precise understanding of sedimentation and flushing behavior. This study used numerical modeling to examine sediment deposition in the Tigris River upstream of the Samarra Barrage. Within the iRIC framework, two models were used: NaysCUBE and Nays2DH. NaysCUBE is a three-dimensional solver that provides detailed simulations of partial gate openings and vertical flow distribution. This capability is crucial for a realistic analysis of the flushing process. Nays2DH is a two-dimensional solver that simulates full gate openings and captures general flow patterns. Results showed that sediment deposits were mostly concentrated within the first kilometer upstream of the dam, particularly when backwater effects caused the outflow to be lower than the inflow. Different gate operation schemes produced varied results: some configurations improved the balance between sediment movement and water flow, whereas others caused local erosion and uneven scouring. Results showed that lowering the water level at the barrage by 1 m increases shear stress on the riverbed by up to 25%, thereby improving the river’s ability to carry sediment without the need for additional discharge. High-discharge flushing operations are no longer feasible because of the reduced flow in the Tigris River since the operation of the Ilisu Dam in Turkey. This study recommends maintaining low water levels at the barrage with frequent and reasonable maintenance operations by partially opening the gates (40–60%). This strategy maintains a balance between the required water storage and sediment control, thereby ensuring the long-term sustainability of the hydraulic structure and the river ecosystem.
- Open Access
- 1 September 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (9) , 3592-3605
Numerical Analysis of Load-Bearing Capacity in Contaminated and Uncontaminated Soils Treated with Nanomaterials
Construction of load-bearing structures requires both a strong foundation and stable soil. For projects located on weak or contaminated soils, stabilization techniques are a prerequisite. Nanotechnology holds promise for improving soil strength and stability, offering innovative solutions for enhancing site conditions in geotechnical engineering. This numerical study explores the potential application of nano-clay (NC) and nano-silica (NS) in improving the overall load-bearing performance of a strip footing resting on clean and kerosene-contaminated soils. The objectives are to assess the impact of varying nanoparticle contents and curing durations on soil performance. Results suggested that adding NC and NS substantially enhances the bearing capacity ratio (BCR) up to a maximum of 4.76 and 4.33 at 1% NC and 1.5% NS, respectively, compared to untreated soil. Overdosing, however, resulted in reduced effectiveness, emphasizing the significance of optimal contents. Conversely, the BCR improvement was less noticeable in kerosene-contaminated soils until it peaked at 2.5% NS and 2% NC. However, results of both clean and contaminated soils revealed that nanomaterials negatively impact settlement behavior. Curing age was found to be a major factor affecting BCR, in which treated soils showed a consistent increase in BCR over time. These findings endorse the potential of nanomaterials for stabilizing soil used in geotechnical engineering. Careful selection of dosages and consideration of soil contamination are critical to optimizing performance in complex geotechnical conditions.
- 1 September 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (9) , 3592-3605
Open AccessNumerical Analysis of Load-Bearing Capacity in Contaminated and Uncontaminated Soils Treated with Nanomaterials
Construction of load-bearing structures requires both a strong foundation and stable soil. For projects located on weak or contaminated soils, stabilization techniques are a prerequisite. Nanotechnology holds promise for improving soil strength and stability, offering innovative solutions for enhancing site conditions in geotechnical engineering. This numerical study explores the potential application of nano-clay (NC) and nano-silica (NS) in improving the overall load-bearing performance of a strip footing resting on clean and kerosene-contaminated soils. The objectives are to assess the impact of varying nanoparticle contents and curing durations on soil performance. Results suggested that adding NC and NS substantially enhances the bearing capacity ratio (BCR) up to a maximum of 4.76 and 4.33 at 1% NC and 1.5% NS, respectively, compared to untreated soil. Overdosing, however, resulted in reduced effectiveness, emphasizing the significance of optimal contents. Conversely, the BCR improvement was less noticeable in kerosene-contaminated soils until it peaked at 2.5% NS and 2% NC. However, results of both clean and contaminated soils revealed that nanomaterials negatively impact settlement behavior. Curing age was found to be a major factor affecting BCR, in which treated soils showed a consistent increase in BCR over time. These findings endorse the potential of nanomaterials for stabilizing soil used in geotechnical engineering. Careful selection of dosages and consideration of soil contamination are critical to optimizing performance in complex geotechnical conditions.
- Open Access
- 8 March 2025
- Published by Tikrit University in Tikrit Journal of Engineering Sciences
- Vol. 32 (1) , 1-18
Numerical Investigation of the Embankment Dam Safety during Rapid Drawdown Conditions Using Horizontal Drains
Rapid drawdown loading condition is a critical state that can cause failure of the upstream slope in earthen dams. Applying upstream horizontal drains has been a prevalent solution to prevent such potential failure. However, existing literature tends to focus on the drains’ geometric and material properties, neglecting the impact of the drawdown rate and geotechnical properties of the dam on the upstream drainage systems’ effectiveness. The present research employs a Finite Element Method, utilizing GeoStudio software, to comprehensively assess the performance of upstream horizontal drains in enhancing slope stability of a homogeneous embankment during rapid drawdown scenarios under varied rates of drawdown and dam properties. The stability analysis results indicated that the factors of safety of the upstream slope at a drawdown rate of 1 m/d and a permeability rate of 10–2 m/d satisfy the minimum safety limits. Notably, introducing upstream drains substantially increased the factors of safety, particularly in scenarios involving faster drawdown rates and slower permeability rates. It was found that the required number of horizontal drains for ensuring the stability of the upstream slope primarily depended on drawdown and permeability rates. However, the presence of upstream drains increased seepage through the upstream face and dam bodies.
- 8 March 2025
- Published by Tikrit University in Tikrit Journal of Engineering Sciences
- Vol. 32 (1) , 1-18
Open AccessNumerical Investigation of the Embankment Dam Safety during Rapid Drawdown Conditions Using Horizontal Drains
Rapid drawdown loading condition is a critical state that can cause failure of the upstream slope in earthen dams. Applying upstream horizontal drains has been a prevalent solution to prevent such potential failure. However, existing literature tends to focus on the drains’ geometric and material properties, neglecting the impact of the drawdown rate and geotechnical properties of the dam on the upstream drainage systems’ effectiveness. The present research employs a Finite Element Method, utilizing GeoStudio software, to comprehensively assess the performance of upstream horizontal drains in enhancing slope stability of a homogeneous embankment during rapid drawdown scenarios under varied rates of drawdown and dam properties. The stability analysis results indicated that the factors of safety of the upstream slope at a drawdown rate of 1 m/d and a permeability rate of 10–2 m/d satisfy the minimum safety limits. Notably, introducing upstream drains substantially increased the factors of safety, particularly in scenarios involving faster drawdown rates and slower permeability rates. It was found that the required number of horizontal drains for ensuring the stability of the upstream slope primarily depended on drawdown and permeability rates. However, the presence of upstream drains increased seepage through the upstream face and dam bodies.
- Open Access
- 29 November 2024
- Published by International Information and Engineering Technology Association in Mathematical Modelling of Engineering Problems
- Vol. 11 (11) , 2919-2928
Effect of Tail Water Depth on Characteristics of Hydraulic Jump Formed Downstream of Stepped Weir
- 29 November 2024
- Published by International Information and Engineering Technology Association in Mathematical Modelling of Engineering Problems
- Vol. 11 (11) , 2919-2928
Open AccessEffect of Tail Water Depth on Characteristics of Hydraulic Jump Formed Downstream of Stepped Weir
- Open Access
- 1 September 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 849 (1) , 012003
Exploration of Rain Gauge Quality Issues in Northern England
The rain gauge, which is the preferred device for rain rate quantification, is susceptible to various types of errors. The problems of inconsistency and incompletion of rainfall time-series, in addition to data quality issues obstruct hydrometeorological analysis. Daily rainfall data from 30 gauges in Northern England were quality controlled by a double quality check procedure for the period 2006–2014 to solve any specific data quality issues. It emerged that fault readings happened only over a few days compared with the high percentage of missing data which could reach years. Thus, factors that impact gauges’ missing data were inspected. It was found that snowfalls, land cover-land use and bird distribution are the dominant factors that malfunctioning the rain gauge for long time periods, often producing successive missing days that could be extended months in total. However, when the missing data happened on separate days, then it seemed that high winds related with light rainfall resulted in drifting away the rainfall from the rain gauge and thus caused missing data. Moreover, the rainfall itself was not one of the major factors to malfunction the gauge, because the values of missed rainfall were not quite extreme to do this.
- 1 September 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 849 (1) , 012003
Open AccessExploration of Rain Gauge Quality Issues in Northern England
The rain gauge, which is the preferred device for rain rate quantification, is susceptible to various types of errors. The problems of inconsistency and incompletion of rainfall time-series, in addition to data quality issues obstruct hydrometeorological analysis. Daily rainfall data from 30 gauges in Northern England were quality controlled by a double quality check procedure for the period 2006–2014 to solve any specific data quality issues. It emerged that fault readings happened only over a few days compared with the high percentage of missing data which could reach years. Thus, factors that impact gauges’ missing data were inspected. It was found that snowfalls, land cover-land use and bird distribution are the dominant factors that malfunctioning the rain gauge for long time periods, often producing successive missing days that could be extended months in total. However, when the missing data happened on separate days, then it seemed that high winds related with light rainfall resulted in drifting away the rainfall from the rain gauge and thus caused missing data. Moreover, the rainfall itself was not one of the major factors to malfunction the gauge, because the values of missed rainfall were not quite extreme to do this.
- Open Access
Uncertainty of Intensity-Duration-Frequency Curves Due to Adoption or Otherwise of the Temperature Climate Variable in Rainfall Disaggregation
Most areas around the world lack fine rainfall records which are needed to derive Intensity-Duration-Frequency (IDF) curves, and those that are available are in the form of daily data. Thus, the disaggregation of rainfall data from coarse to fine temporal resolution may offer a solution to that problem. Most of the previous studies have adopted only historical rainfall data as the predictor to disaggregate daily rainfall data to hourly resolution, while only a few studies have adopted other historical climate variables besides rainfall for such a purpose. Therefore, this study adopts and assesses the performance of two methods of rainfall disaggregation one uses for historical temperature and rainfall variables while the other uses only historical rainfall data for disaggregation. The two methods are applied to disaggregate the current observed and projected modeled daily rainfall data to an hourly scale for a small urban area in the United Kingdom. Then, the IDF curves for the current and future climates are derived for each case of disaggregation and compared. After which, the uncertainties associated with the difference between the two cases are assessed. The constructed IDF curves (for the two cases of disaggregation) agree in the sense that they both show that there is a big difference between the current and future climates for all durations and frequencies. However, the uncertainty related to the difference between the results of the constructed IDF curves (for the two cases of disaggregation) for each climate is considerable, especially for short durations and long return periods. In addition, the projected and current rainfall values based on disaggregation case which adopts historical temperature and rainfall variables were higher than the corresponding projections and current values based on only rainfall data for the disaggregation.
Open AccessUncertainty of Intensity-Duration-Frequency Curves Due to Adoption or Otherwise of the Temperature Climate Variable in Rainfall Disaggregation
Most areas around the world lack fine rainfall records which are needed to derive Intensity-Duration-Frequency (IDF) curves, and those that are available are in the form of daily data. Thus, the disaggregation of rainfall data from coarse to fine temporal resolution may offer a solution to that problem. Most of the previous studies have adopted only historical rainfall data as the predictor to disaggregate daily rainfall data to hourly resolution, while only a few studies have adopted other historical climate variables besides rainfall for such a purpose. Therefore, this study adopts and assesses the performance of two methods of rainfall disaggregation one uses for historical temperature and rainfall variables while the other uses only historical rainfall data for disaggregation. The two methods are applied to disaggregate the current observed and projected modeled daily rainfall data to an hourly scale for a small urban area in the United Kingdom. Then, the IDF curves for the current and future climates are derived for each case of disaggregation and compared. After which, the uncertainties associated with the difference between the two cases are assessed. The constructed IDF curves (for the two cases of disaggregation) agree in the sense that they both show that there is a big difference between the current and future climates for all durations and frequencies. However, the uncertainty related to the difference between the results of the constructed IDF curves (for the two cases of disaggregation) for each climate is considerable, especially for short durations and long return periods. In addition, the projected and current rainfall values based on disaggregation case which adopts historical temperature and rainfall variables were higher than the corresponding projections and current values based on only rainfall data for the disaggregation.
- 19 April 2021
- Published by Taylor & Francis in International Journal of River Basin Management
- Vol. 21 (1) , 53-65
Simulation of flow around a permeable dike using physical and 3D-CFD models
In this research, complementary numerical and experimental physical models were conducted to investigate flow parameters around an isolated permeable spur dike using ANSYS FLUENT ver. 16.1 software. The volume of fluid method VOF with the help of CFD technique and the turbulence model was used to simulate the complex free-surface flow by applying a geometric reconstruction scheme. Two different medium with different porosities were used, namely, gravel and glass beads. It was found that, for low flow rates values, there are no significant changes in the water profiles in both longitudinal and lateral directions for both media. Although for high flow rates values, the differences tend to be clearer. Results showed that there is a slight effects of the medium's properties if the dike width is less than 1/3 of width of the channel, in particular with low flow rate values. Good agreement was observed between the computational and the measured results for the water surface profiles. Also, there is an exact match between the lateral velocity distribution of gravels and glass beads. Downstream the dike, the lateral velocity profiles exhibit an S shape curve due to high velocity in the free flow and small flow velocity behind the porous dike. The results show good agreement between the CFD results and the experimental observations of the water surface profiles and velocity distribution according to the statistical analysis using some standard indexes error.- 19 April 2021
- Published by Taylor & Francis in International Journal of River Basin Management
- Vol. 21 (1) , 53-65
Simulation of flow around a permeable dike using physical and 3D-CFD models
In this research, complementary numerical and experimental physical models were conducted to investigate flow parameters around an isolated permeable spur dike using ANSYS FLUENT ver. 16.1 software. The volume of fluid method VOF with the help of CFD technique and the turbulence model was used to simulate the complex free-surface flow by applying a geometric reconstruction scheme. Two different medium with different porosities were used, namely, gravel and glass beads. It was found that, for low flow rates values, there are no significant changes in the water profiles in both longitudinal and lateral directions for both media. Although for high flow rates values, the differences tend to be clearer. Results showed that there is a slight effects of the medium's properties if the dike width is less than 1/3 of width of the channel, in particular with low flow rate values. Good agreement was observed between the computational and the measured results for the water surface profiles. Also, there is an exact match between the lateral velocity distribution of gravels and glass beads. Downstream the dike, the lateral velocity profiles exhibit an S shape curve due to high velocity in the free flow and small flow velocity behind the porous dike. The results show good agreement between the CFD results and the experimental observations of the water surface profiles and velocity distribution according to the statistical analysis using some standard indexes error.- Open Access
- 22 October 2020
- Published by EDP Sciences
- Vol. 199, 00003
Adsorption Technique for Drainage Water Treatment
This study evaluated the suitability of an adsorption technique in drainage water treatment for irrigation purposes. The water samples for this study were sourced from different spots of Al-MASAB AL A’AM river. Three different locations (Latifia, Yusufiyah, and Swerah area) were considered in this study. Several studies have reported the use of activated carbon and ion exchangers for water treatment. In this work, a cheap alternative bio-filtration media (activated carbon derived from Apricot stones (ASAC)) was used. Several parameters are required in this technique for various estimations; such parameters include the chemical and physical properties of the water samples (like the pH, ionic concentration, electrical conductivity (EC), and total dissolved solids (TDS). The Freundlich equations was also applied to study the chemical adsorption process using ASAC. Also calculated were the adsorption constant (k) and the number of adsorbents (n). From the results of this study, the applied process was suitable for the removal of Ca+2, Mg+2andCO3-2ions from the sampled water.
- 22 October 2020
- Published by EDP Sciences
- Vol. 199, 00003
Open AccessAdsorption Technique for Drainage Water Treatment
This study evaluated the suitability of an adsorption technique in drainage water treatment for irrigation purposes. The water samples for this study were sourced from different spots of Al-MASAB AL A’AM river. Three different locations (Latifia, Yusufiyah, and Swerah area) were considered in this study. Several studies have reported the use of activated carbon and ion exchangers for water treatment. In this work, a cheap alternative bio-filtration media (activated carbon derived from Apricot stones (ASAC)) was used. Several parameters are required in this technique for various estimations; such parameters include the chemical and physical properties of the water samples (like the pH, ionic concentration, electrical conductivity (EC), and total dissolved solids (TDS). The Freundlich equations was also applied to study the chemical adsorption process using ASAC. Also calculated were the adsorption constant (k) and the number of adsorbents (n). From the results of this study, the applied process was suitable for the removal of Ca+2, Mg+2andCO3-2ions from the sampled water.
- Open Access
- 15 September 2020
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 24 (12) , 3674-3691
Physical and CFD Simulated Models to Analyze the Contaminant Transport through Porous Media under Hydraulic Structures
- 15 September 2020
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 24 (12) , 3674-3691
Open AccessPhysical and CFD Simulated Models to Analyze the Contaminant Transport through Porous Media under Hydraulic Structures
- Open Access
- 31 August 2017
- Published by Journal of Engineering in Journal of Engineering
- Vol. 23 (9) , 1-22
Optimum Dimensions of Hydraulic Structures and Foundation Using Genetic Algorithm coupled with Artificial Neural Network
A model using the artificial neural networks and genetic algorithm technique is developed for obtaining optimum dimensions of the foundation length and protections of small hydraulic structures. The procedure involves optimizing an objective function comprising a weighted summation of the state variables. The decision variables considered in the optimization are the upstream and downstream cutoffs lengths and their angles of inclination, the foundation length, and the length of the downstream soil protection. These were obtained for a given maximum difference in head, depth of impervious layer and degree of anisotropy. The optimization carried out is subjected to constraints that ensure a safe structure against the uplift pressure force and sufficient protection length at the downstream side of the structure to overcome an excessive exit gradient. The Geo-studio software was used to analyze 1200 different cases. For each case the length of protection (L) and volume of structure (V) required to satisfy the safety factors mentioned previously were estimated for the input values, namely, the upstream cutoff depth (S1), the downstream cutoff depth (S2), the foundation width (B), the angle of inclination of the upstream cutoff (Ɵ1) and the angle of inclination of the downstream cutoff (Ɵ2), H (differencehead), kr (degree of anisotropy) and D (depth of impervious layer). An ANN model was developed and verified using these cases input-output sets as its data base. A MatLAB code was written to perform a genetic algorithm optimization modeling coupled with this ANN model using a formulated optimization model. A sensitivity analysis was done for selecting the crossover probability, the mutation probability and level, the number of population, the position of the crossover and the weights distribution for all the terms of the objective function. Results indicate that the most factors that affects. the optimum solution is the $ number of population required. The minimum value that gives stable global optimum solution of this parameter is (30000) while other variables have little effect on the optimum solution.
- 31 August 2017
- Published by Journal of Engineering in Journal of Engineering
- Vol. 23 (9) , 1-22
Open AccessOptimum Dimensions of Hydraulic Structures and Foundation Using Genetic Algorithm coupled with Artificial Neural Network
A model using the artificial neural networks and genetic algorithm technique is developed for obtaining optimum dimensions of the foundation length and protections of small hydraulic structures. The procedure involves optimizing an objective function comprising a weighted summation of the state variables. The decision variables considered in the optimization are the upstream and downstream cutoffs lengths and their angles of inclination, the foundation length, and the length of the downstream soil protection. These were obtained for a given maximum difference in head, depth of impervious layer and degree of anisotropy. The optimization carried out is subjected to constraints that ensure a safe structure against the uplift pressure force and sufficient protection length at the downstream side of the structure to overcome an excessive exit gradient. The Geo-studio software was used to analyze 1200 different cases. For each case the length of protection (L) and volume of structure (V) required to satisfy the safety factors mentioned previously were estimated for the input values, namely, the upstream cutoff depth (S1), the downstream cutoff depth (S2), the foundation width (B), the angle of inclination of the upstream cutoff (Ɵ1) and the angle of inclination of the downstream cutoff (Ɵ2), H (differencehead), kr (degree of anisotropy) and D (depth of impervious layer). An ANN model was developed and verified using these cases input-output sets as its data base. A MatLAB code was written to perform a genetic algorithm optimization modeling coupled with this ANN model using a formulated optimization model. A sensitivity analysis was done for selecting the crossover probability, the mutation probability and level, the number of population, the position of the crossover and the weights distribution for all the terms of the objective function. Results indicate that the most factors that affects. the optimum solution is the $ number of population required. The minimum value that gives stable global optimum solution of this parameter is (30000) while other variables have little effect on the optimum solution.