Rummenigge Rudson Dantas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rummenigge Rudson Dantas has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Luiz Marcos Garcia Gonçalves
Federal University of Rio Grande do Norte
12 shared publications - Aquiles Medeiros Filgueira Burlamaqui
Universidade Federal do Rio Grande do Norte
9 shared publications Josivan Xavier
Universidade Federal do Rio Grande do Norte, DCA-CT-UFRN, Campus Universitário, Lagoa Nova, CEP 59.072-970, Natal, Brazil
6 shared publicationsClaudio Schneider
Universidade Federal do Rio Grande do Norte, Brasil
5 shared publicationsSamuel Azevedo
5 shared publicationsClaudio A. Schneider
Universidade Federal do Rio Grande do Norte ECT-UFRN
4 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Sociedade Brasileira de Computação in Journal on Interactive Systems
- Vol. 17 (1) , 926-937
Enhancing STEM Learning through Interactive Digital Twins: Architecture of a Low-Cost Web Solution for Robotics
Educational robotics is a powerful approach for developing STEM skills; however, its widespread adoption is often constrained by the high cost of commercial robotic kits and by the complexity of integrating physical hardware with virtual learning environments. In the context of Industry 4.0, the Digital Twin (DT) concept emerges as a strategic bridge between physical assets and virtual models, yet its application in basic and higher education remains limited by technical and financial barriers. Purpose: To address these challenges, this article presents a web-based Digital Twin architecture that utilizes the low-cost mobile educational platform URA (One Robot per Student) as a case study. The study aims to provide an accessible and scalable solution for real-time monitoring, simulation, and remote interaction, democratizing access to advanced robotics and IoT concepts. Methods: The proposed system integrates an ESP32-based physical robot with a web interface implemented using React.js and Three.js. Communication between the physical and virtual layers is achieved via the MQTT protocol to ensure low-latency data exchange. The platform includes a three-dimensional visualization module for state monitoring and an augmented reality component to support immersive interaction. The research methodology involved a technical evaluation focused on communication latency and synchronization fidelity between the robot’s sensor data (ultrasonic, vibration, and magnetometer) and its virtual counterpart. Furthermore, the study analyzes the pedagogical alignment of the platform with constructivist and constructionist learning principles, emphasizing the importance of active experimentation. Results: Technical evaluations indicate that the system maintains responsiveness and synchronization accuracy within acceptable limits for educational applications, with average latency levels suitable for real-time user perception. The orientation error observed between the physical and virtual entities remained minimal, ensuring a high-fidelity representation. Additionally, the estimated cost of the essential electronic components is approximately US$24.72, which is substantially lower than that of commercial educational robotics platforms, such as Lego Mindstorms. This financial accessibility allows for the replication of the project in resource-constrained institutions. Conclusion: These results demonstrate that the proposed Digital Twin constitutes a viable and cost-effective solution for educational robotics. By enabling students to safely experiment in virtual environments before validating their solutions on real hardware, the platform effectively reduces financial and technical barriers in STEM education. The integration of web technologies and open-source hardware reinforces the scalability of the approach, contributing to the democratization of advanced simulation technologies in the teaching-learning process.
- 1 January 2026
- Published by Sociedade Brasileira de Computação in Journal on Interactive Systems
- Vol. 17 (1) , 926-937
Open AccessEnhancing STEM Learning through Interactive Digital Twins: Architecture of a Low-Cost Web Solution for Robotics
Educational robotics is a powerful approach for developing STEM skills; however, its widespread adoption is often constrained by the high cost of commercial robotic kits and by the complexity of integrating physical hardware with virtual learning environments. In the context of Industry 4.0, the Digital Twin (DT) concept emerges as a strategic bridge between physical assets and virtual models, yet its application in basic and higher education remains limited by technical and financial barriers. Purpose: To address these challenges, this article presents a web-based Digital Twin architecture that utilizes the low-cost mobile educational platform URA (One Robot per Student) as a case study. The study aims to provide an accessible and scalable solution for real-time monitoring, simulation, and remote interaction, democratizing access to advanced robotics and IoT concepts. Methods: The proposed system integrates an ESP32-based physical robot with a web interface implemented using React.js and Three.js. Communication between the physical and virtual layers is achieved via the MQTT protocol to ensure low-latency data exchange. The platform includes a three-dimensional visualization module for state monitoring and an augmented reality component to support immersive interaction. The research methodology involved a technical evaluation focused on communication latency and synchronization fidelity between the robot’s sensor data (ultrasonic, vibration, and magnetometer) and its virtual counterpart. Furthermore, the study analyzes the pedagogical alignment of the platform with constructivist and constructionist learning principles, emphasizing the importance of active experimentation. Results: Technical evaluations indicate that the system maintains responsiveness and synchronization accuracy within acceptable limits for educational applications, with average latency levels suitable for real-time user perception. The orientation error observed between the physical and virtual entities remained minimal, ensuring a high-fidelity representation. Additionally, the estimated cost of the essential electronic components is approximately US$24.72, which is substantially lower than that of commercial educational robotics platforms, such as Lego Mindstorms. This financial accessibility allows for the replication of the project in resource-constrained institutions. Conclusion: These results demonstrate that the proposed Digital Twin constitutes a viable and cost-effective solution for educational robotics. By enabling students to safely experiment in virtual environments before validating their solutions on real hardware, the platform effectively reduces financial and technical barriers in STEM education. The integration of web technologies and open-source hardware reinforces the scalability of the approach, contributing to the democratization of advanced simulation technologies in the teaching-learning process.
- Open Access
- 1 January 2024
- Published by Sociedade Brasileira de Computação in Journal on Interactive Systems
- Vol. 15 (1) , 143-156
TeamBridge 2.0: an extensible and non-invasive middleware for control and adapting games for motor rehabilitation
This work present the TeamBridge 2.0, a middleware able to perform the communication between digital games and hardware devices, like joysticks, mice and cameras (both rgbd and monocular). That communication does not require any modification to the game source code, allowing an old game to be adapted to work with a new hardware device. To prove this, tests were carried out with several games, including one of them being a commercial game. This middleware also allows the use of more than one device at the same time, so we can obtain more accurate information, one device can supply the deficiencies of the other. Finally, we performed tests to make sure that the middleware would not interfere with the user experience. Tests have shown that TeamBridge 2.0 can receive, interpret and send information quickly, the time varies according to the device used, getting 33ms when used with Kinect, 40ms with Leap Motion and 255ms with a DIY Data-Glove.
- 1 January 2024
- Published by Sociedade Brasileira de Computação in Journal on Interactive Systems
- Vol. 15 (1) , 143-156
Open AccessTeamBridge 2.0: an extensible and non-invasive middleware for control and adapting games for motor rehabilitation
This work present the TeamBridge 2.0, a middleware able to perform the communication between digital games and hardware devices, like joysticks, mice and cameras (both rgbd and monocular). That communication does not require any modification to the game source code, allowing an old game to be adapted to work with a new hardware device. To prove this, tests were carried out with several games, including one of them being a commercial game. This middleware also allows the use of more than one device at the same time, so we can obtain more accurate information, one device can supply the deficiencies of the other. Finally, we performed tests to make sure that the middleware would not interfere with the user experience. Tests have shown that TeamBridge 2.0 can receive, interpret and send information quickly, the time varies according to the device used, getting 33ms when used with Kinect, 40ms with Leap Motion and 255ms with a DIY Data-Glove.
- Open Access
- 24 October 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-10
A non-invasive middleware for games adaptation and motor rehabilitation controls
This work present the TeamBridge, a middleware able to perform the communication between digital games and hardware devices, like joysticks, mice and motion capture cameras. That communication does not require any modification to the game source code, allowing an old game to be adapted to work with a new hardware device. To prove this, tests were carried out with several games, including one of them being a commercial game. This middleware also allows the use of more than one device at the same time, so we can obtain more accurate information, one device can supply the deficiencies of the other. Finally, we performed tests to make sure that the middleware would not interfere with the user experience. Tests have shown that TeamBridge can receive, interpret and send information quickly, the time varies according to the device used, getting 33ms when used with Kinect, 40ms with Leap Motion and 255ms with the NED Glove.
- 24 October 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-10
Open AccessA non-invasive middleware for games adaptation and motor rehabilitation controls
This work present the TeamBridge, a middleware able to perform the communication between digital games and hardware devices, like joysticks, mice and motion capture cameras. That communication does not require any modification to the game source code, allowing an old game to be adapted to work with a new hardware device. To prove this, tests were carried out with several games, including one of them being a commercial game. This middleware also allows the use of more than one device at the same time, so we can obtain more accurate information, one device can supply the deficiencies of the other. Finally, we performed tests to make sure that the middleware would not interfere with the user experience. Tests have shown that TeamBridge can receive, interpret and send information quickly, the time varies according to the device used, getting 33ms when used with Kinect, 40ms with Leap Motion and 255ms with the NED Glove.
- Open Access
- 18 June 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (8) , e160985594
Interface physiohappy no tratamento de punho e mão de criança com paralisia cerebral: relato de caso
O objetivo do estudo foi verificar a aplicabilidade da realidade virtual (RV) utilizando a interface de baixo custo PhysioHappy, associada à fisioterapia convencional na reabilitação de punho e mão de indivíduos com Paralisia Cerebral (PC) espástica unilateral. Trata-se de um relato de caso que descreve a reabilitação de uma menina de 12 anos com PC espástica direita unilateral submetida a um tratamento de 12 sessões com fisioterapia convencional e interface PhysioHappy. Verificou-se que a criança melhorou a destreza manual no Box and Block test e a ativação muscular de extensores e flexores de punho e mão aferida através da eletromiografia. Concluiu-se que a interface utilizada associada à fisioterapia convencional pode ser considerada como o tratamento de uma criança com Paralisia Cerebral espástica, expandindo as estratégias terapêuticas existentes.
- 18 June 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (8) , e160985594
Open AccessInterface physiohappy no tratamento de punho e mão de criança com paralisia cerebral: relato de caso
O objetivo do estudo foi verificar a aplicabilidade da realidade virtual (RV) utilizando a interface de baixo custo PhysioHappy, associada à fisioterapia convencional na reabilitação de punho e mão de indivíduos com Paralisia Cerebral (PC) espástica unilateral. Trata-se de um relato de caso que descreve a reabilitação de uma menina de 12 anos com PC espástica direita unilateral submetida a um tratamento de 12 sessões com fisioterapia convencional e interface PhysioHappy. Verificou-se que a criança melhorou a destreza manual no Box and Block test e a ativação muscular de extensores e flexores de punho e mão aferida através da eletromiografia. Concluiu-se que a interface utilizada associada à fisioterapia convencional pode ser considerada como o tratamento de uma criança com Paralisia Cerebral espástica, expandindo as estratégias terapêuticas existentes.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 341-344
Evaluate Leap Motion Control for Multiple Hand Posture Recognition
Leap Motion is a device that turns hands and fingers into input devices, it is possible to control the computer by replacing the mouse and / or keyboard. The Laboratory of Educational, Auxiliary and Multimedia Technologies of the Federal University of Rio Grande do Norte develops prototype gloves and virtual games, that are used in rehabilitation sessions for people who have suffered a stroke. The objective of this work is to verify if it is possible to replace the prototypes by Leap Motion and to qualify the interactions with the user at the moment of the rehabilitation.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 341-344
Evaluate Leap Motion Control for Multiple Hand Posture Recognition
Leap Motion is a device that turns hands and fingers into input devices, it is possible to control the computer by replacing the mouse and / or keyboard. The Laboratory of Educational, Auxiliary and Multimedia Technologies of the Federal University of Rio Grande do Norte develops prototype gloves and virtual games, that are used in rehabilitation sessions for people who have suffered a stroke. The objective of this work is to verify if it is possible to replace the prototypes by Leap Motion and to qualify the interactions with the user at the moment of the rehabilitation.
- 1 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 13, 1-6
PHYS.IO: Wearable hand tracking device
This paper describes the development of a human computer interface focused in detect hand movements and gestures and apply this data into a 3D environment, all this running based on an Android mobile device.
- 1 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 13, 1-6
PHYS.IO: Wearable hand tracking device
This paper describes the development of a human computer interface focused in detect hand movements and gestures and apply this data into a 3D environment, all this running based on an Android mobile device.
- 1 July 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23779314,p. 55-59
Development of a low cost dataglove based on arduino for virtual reality applications
This article describes the first steps on the development of a low cost dataglove based on the Arduino Uno microprocessor. The glove is designed for use in virtual reality systems and is integrated into a suite of applications. This article also presents a set of preliminary results obtained with the glove and discuss about the use of the glove to control a video game application for rehabilitation of stroke patients.
- 1 July 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23779314,p. 55-59
Development of a low cost dataglove based on arduino for virtual reality applications
This article describes the first steps on the development of a low cost dataglove based on the Arduino Uno microprocessor. The glove is designed for use in virtual reality systems and is integrated into a suite of applications. This article also presents a set of preliminary results obtained with the glove and discuss about the use of the glove to control a video game application for rehabilitation of stroke patients.
- 1 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 260-263
FlexDGlove: A Low Cost Dataglove with Virtual Hand Simulator for Virtual Reality Applications
This article describes the development of a low cost data glove called FlexDglove. This system was designed for virtual reality applications and includes an integrated virtual hand simulator. The development steps are described and also a set of preliminary results about the use of this glove.
- 1 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 260-263
FlexDGlove: A Low Cost Dataglove with Virtual Hand Simulator for Virtual Reality Applications
This article describes the development of a low cost data glove called FlexDglove. This system was designed for virtual reality applications and includes an integrated virtual hand simulator. The development steps are described and also a set of preliminary results about the use of this glove.
- Open Access
- 1 January 2013
- Published by Editora Cubo in Research on Biomedical Engineering
- Vol. 29 (2) , 206-210
Um Anjo para ELA: Arquitetura Baseada em Visão Computacional Aplicada ao Monitoramento On-Line de Parâmetros Respiratórios de Pacientes com Esclerose Lateral Amiotrófica (ELA) em Ambiente Hospitalar
- 1 January 2013
- Published by Editora Cubo in Research on Biomedical Engineering
- Vol. 29 (2) , 206-210
Open AccessUm Anjo para ELA: Arquitetura Baseada em Visão Computacional Aplicada ao Monitoramento On-Line de Parâmetros Respiratórios de Pacientes com Esclerose Lateral Amiotrófica (ELA) em Ambiente Hospitalar
- 1 January 2013
- Published by IGI Global Scientific Publishing
- p. 1005-1021
Using Interactive Digital Television Middleware Tools to Promote Facilities for Healthcare and Social Services
This chapter introduces the use of middleware tools in applications for healthcare and social services, focusing on solutions designed for Interactive Digital Television (IDTV), and discusses its implications to modern roles for easing patient and caretaker relations. The authors explore the capacities of such solutions to assist the patients in their personal needs, optimizing the time and tasks of the caretaker. They discuss the limits of the use of Internet in satisfying the needs of communication of elderly and other patients, and then they propose new roles for caretaking based on this new reality. The authors also present an architecture that allows the remote use and control of electronic devices via IDTV set-top boxes for the middleware Ginga. They show applications based on this architecture that promote healthcare and social services, as a set of infrared lights coupled to a hat that can be used as input for impaired patients, and how an accelerometer can be used with IDTV applications for treatment and entertainment. Before concluding, the authors point out research directions on the topics discussed in this chapter.
- 1 January 2013
- Published by IGI Global Scientific Publishing
- p. 1005-1021
Using Interactive Digital Television Middleware Tools to Promote Facilities for Healthcare and Social Services
This chapter introduces the use of middleware tools in applications for healthcare and social services, focusing on solutions designed for Interactive Digital Television (IDTV), and discusses its implications to modern roles for easing patient and caretaker relations. The authors explore the capacities of such solutions to assist the patients in their personal needs, optimizing the time and tasks of the caretaker. They discuss the limits of the use of Internet in satisfying the needs of communication of elderly and other patients, and then they propose new roles for caretaking based on this new reality. The authors also present an architecture that allows the remote use and control of electronic devices via IDTV set-top boxes for the middleware Ginga. They show applications based on this architecture that promote healthcare and social services, as a set of infrared lights coupled to a hat that can be used as input for impaired patients, and how an accelerometer can be used with IDTV applications for treatment and entertainment. Before concluding, the authors point out research directions on the topics discussed in this chapter.