Petr V. Nikolenko
Research Subjects
Petr V. Nikolenko has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- V. L. Shkuratnik
National University of Science and Technology—MISiS
12 shared publications A. A. Kormnov
3 shared publicationsA. E. Koshelev
GAZPROM Geotechnology
3 shared publicationsM. D. Chepur
3 shared publicationsNational University of Science and Technology «MISiS»
3 shared publicationsV. L. Shkuratnik
National University of Science and Technology—MISIS, Moscow, Russia
3 shared publications
Latest Publications
- 1 January 2023
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 1,p. 95-106
Integrated acoustic and optical logging in adjacent rock mass. Equipment and physical modeling
- 1 January 2023
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 1,p. 95-106
Integrated acoustic and optical logging in adjacent rock mass. Equipment and physical modeling
- 1 December 2022
- Published by Pleiades Publishing Ltd in Journal of Mining Science
- Vol. 58 (6) , 936-944
Effect of Discontinuities on Elastic Wave Velocities in High-Stress Rock Samples: Experimental Research Using Ultrasonic Interferometry
The scope of the experimental research embraces velocities of elastic waves in rock samples before and after formation of a horizontal main crack. In undamaged samples, there is no essential change in the elastic wave velocity as the axial pressure increases from 0 to 20 MPa. The main crack having its surfaces approaching gradually leads to the increase in the elastic wave velocity. Aimed to improve sensibility of kinematic ultrasonic parameters relative to mechanical stresses, the coda wave interferometry algorithm is implemented as an analysis of times of the first arrivals of multiply scattered waves. With the mentioned algorithm, sensibility of the ultrasonic control grows considerably even in uniform samples.
- 1 December 2022
- Published by Pleiades Publishing Ltd in Journal of Mining Science
- Vol. 58 (6) , 936-944
Effect of Discontinuities on Elastic Wave Velocities in High-Stress Rock Samples: Experimental Research Using Ultrasonic Interferometry
The scope of the experimental research embraces velocities of elastic waves in rock samples before and after formation of a horizontal main crack. In undamaged samples, there is no essential change in the elastic wave velocity as the axial pressure increases from 0 to 20 MPa. The main crack having its surfaces approaching gradually leads to the increase in the elastic wave velocity. Aimed to improve sensibility of kinematic ultrasonic parameters relative to mechanical stresses, the coda wave interferometry algorithm is implemented as an analysis of times of the first arrivals of multiply scattered waves. With the mentioned algorithm, sensibility of the ultrasonic control grows considerably even in uniform samples.
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 3,p. 5-15
Surface roughness estimation and rock type identification by ultrasonic and optical techniques
В современной практике геоконтроля изучение структуры и состояния приконтурного массива производится с применением различных геофизических методов, в частности методов ультразвукового прозвучивания и каротажа. Особенностью таких измерений является неизбежная необходимость использования сухого контакта на границе «преобразователь-массив», что значительно снижает надежность получаемой информации. Расширение возможностей акустических скважинных методов исследования приконтурного массива возможно на основе их комплексирования с результатами бесконтактного оптического сканирования стенок скважин. Представлены результаты экспериментальных исследований различных типов пород, проведенных специально разработанными оптическими электронными модулями. Показано, что шероховатость поверхности породы можно определять на основе анализа интенсивности отраженного света, при этом в качестве основных информативных параметров могут выступать коэффициент вариации и коэффициент корреляции сигналов, зарегистрированных вдоль одного профиля двумя фоточувствительными элементами. Также экспериментально продемонстрировано влияние шероховатости поверхности на параметры ультразвуковых импульсов, заключающееся в снижении энергии и сужении спектра сигналов. Доказано, что энергией импульсов можно управлять, изменяя усилие прижима преобразователя в диапазоне давлений от 0 до 2,5 атм. Также продемонстрирована возможность атрибутирования типа породы на основе анализа интенсивности отраженного света на различных длинах волн, что может быть использовано для повышения надежности ультразвукового каротажа приконтурного массива, сложенного породами со схожими акустическими...
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 3,p. 5-15
Surface roughness estimation and rock type identification by ultrasonic and optical techniques
В современной практике геоконтроля изучение структуры и состояния приконтурного массива производится с применением различных геофизических методов, в частности методов ультразвукового прозвучивания и каротажа. Особенностью таких измерений является неизбежная необходимость использования сухого контакта на границе «преобразователь-массив», что значительно снижает надежность получаемой информации. Расширение возможностей акустических скважинных методов исследования приконтурного массива возможно на основе их комплексирования с результатами бесконтактного оптического сканирования стенок скважин. Представлены результаты экспериментальных исследований различных типов пород, проведенных специально разработанными оптическими электронными модулями. Показано, что шероховатость поверхности породы можно определять на основе анализа интенсивности отраженного света, при этом в качестве основных информативных параметров могут выступать коэффициент вариации и коэффициент корреляции сигналов, зарегистрированных вдоль одного профиля двумя фоточувствительными элементами. Также экспериментально продемонстрировано влияние шероховатости поверхности на параметры ультразвуковых импульсов, заключающееся в снижении энергии и сужении спектра сигналов. Доказано, что энергией импульсов можно управлять, изменяя усилие прижима преобразователя в диапазоне давлений от 0 до 2,5 атм. Также продемонстрирована возможность атрибутирования типа породы на основе анализа интенсивности отраженного света на различных длинах волн, что может быть использовано для повышения надежности ультразвукового каротажа приконтурного массива, сложенного породами со схожими акустическими...
- 1 January 2021
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 7,p. 5-13
Velocity variations of Pand S-waves in sedimentary rock samples under thermobaric effects
Статья посвящена исследованию изменения параметров распространения продольных и поперечных волн в осадочных горных породах в функции от температуры, давления, а также специфики их строения. В экспериментальных исследованиях образцы пяти групп осадочных пород с различными значениями пористости и плотности подвергались одноосному нагружению с одновременным нагревом. На каждом этапе термобарического нагружения производилось ультразвуковое прозвучивание продольными и поперечнми волнами. По полученным данным вычислялись показатели, описывающие приращение скорости упругих волн с увеличением осевой нагрузки, а также оценивалось влияние температуры на указанные приращения. Установлено, что рост нагрузки приводит к увеличению скорости распространения упругих волн пропорционально пористости образцов и обратно пропорционально их плотности. Нагрев породы приводит к повышению чувствительности ультразвуковых параметров к изменениям величины осевого давления. В результате спектрального анализа зарегистрированных сигналов было выявлено смещение максимума спектра продольных волн с увеличением температуры, что свидетельствует об образовании трещин. При этом интенсивность трещинообразования выше в более плотных породах. Полученные закономерности могут быть использованы для разработки эффективных методов ультразвукового контроля напряженно-деформированного состояния приконтурного массива горных...
- 1 January 2021
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 7,p. 5-13
Velocity variations of Pand S-waves in sedimentary rock samples under thermobaric effects
Статья посвящена исследованию изменения параметров распространения продольных и поперечных волн в осадочных горных породах в функции от температуры, давления, а также специфики их строения. В экспериментальных исследованиях образцы пяти групп осадочных пород с различными значениями пористости и плотности подвергались одноосному нагружению с одновременным нагревом. На каждом этапе термобарического нагружения производилось ультразвуковое прозвучивание продольными и поперечнми волнами. По полученным данным вычислялись показатели, описывающие приращение скорости упругих волн с увеличением осевой нагрузки, а также оценивалось влияние температуры на указанные приращения. Установлено, что рост нагрузки приводит к увеличению скорости распространения упругих волн пропорционально пористости образцов и обратно пропорционально их плотности. Нагрев породы приводит к повышению чувствительности ультразвуковых параметров к изменениям величины осевого давления. В результате спектрального анализа зарегистрированных сигналов было выявлено смещение максимума спектра продольных волн с увеличением температуры, что свидетельствует об образовании трещин. При этом интенсивность трещинообразования выше в более плотных породах. Полученные закономерности могут быть использованы для разработки эффективных методов ультразвукового контроля напряженно-деформированного состояния приконтурного массива горных...
- 31 December 2020
- Published by Pleiades Publishing Ltd in Journal of Mining Science
- Vol. 57 (1) , 1-9
FAILURE MECHANISM OF COAL UNDER FREEZE–THAW CONDITIONS FROM THE SPECTRUM ANALYSIS OF ULTRASONIC SCANNING DATA
The samples of anthracite and bituminous coal are studied in cyclic freeze–thaw at different water contents. In the freeze–thaw cycles, the samples were subjected to continuous ultrasonic sounding. It is found that different contents of water have an essential influence on the spectrum of recorded signals. Regarding the water-unsaturated check samples, the spectrum change is reversible, and the freeze–thaw treatment results in no failure. An increase in the water content of the samples fosters the irreversible change in the spectra of the signals against the background of macro-cracking along stratification planes. Anthracite exhibits higher persistence to freeze–thaw damage than bituminous coal.
- 31 December 2020
- Published by Pleiades Publishing Ltd in Journal of Mining Science
- Vol. 57 (1) , 1-9
FAILURE MECHANISM OF COAL UNDER FREEZE–THAW CONDITIONS FROM THE SPECTRUM ANALYSIS OF ULTRASONIC SCANNING DATA
The samples of anthracite and bituminous coal are studied in cyclic freeze–thaw at different water contents. In the freeze–thaw cycles, the samples were subjected to continuous ultrasonic sounding. It is found that different contents of water have an essential influence on the spectrum of recorded signals. Regarding the water-unsaturated check samples, the spectrum change is reversible, and the freeze–thaw treatment results in no failure. An increase in the water content of the samples fosters the irreversible change in the spectra of the signals against the background of macro-cracking along stratification planes. Anthracite exhibits higher persistence to freeze–thaw damage than bituminous coal.
- Open Access
- 10 August 2020
- Published by Springer Nature in International Journal of Coal Science & Technology
- Vol. 8 (4) , 562-574
Experimental study of coal fracture dynamics under the influence of cyclic freezing–thawing using shear elastic waves
Cyclic freezing–thawing can lead to fracture development in coal, affecting its mechanical and consumer properties. To study crack formations in coal, an ultrasonic sounding method using shear polarized waves was proposed. Samples of three coal types (anthracite, lignite and hard coal) were tested. The research results show that, in contrast to the shear wave velocity, the shear wave amplitude is extremely sensitive to the formation of new cracks at the early stages of cyclic freezing–thawing. Tests also show an inverse correlation between coal compressive strength and its tendency to form cracks under temperature impacts; shear wave attenuation increases more sharply in high-rank coals after the first freezing cycle. Spectral analysis of the received signals also confirmed significant crack formation in anthracite after the first freeze–thaw cycle. The initial anisotropy was determined, and its decrease with an increase in the number of freeze–thaw cycles was shown. The data obtained forms an experimental basis for the development of new approaches to preserve coal consumer properties during storage and transportation under severe natural and climatic conditions.
- 10 August 2020
- Published by Springer Nature in International Journal of Coal Science & Technology
- Vol. 8 (4) , 562-574
Open AccessExperimental study of coal fracture dynamics under the influence of cyclic freezing–thawing using shear elastic waves
Cyclic freezing–thawing can lead to fracture development in coal, affecting its mechanical and consumer properties. To study crack formations in coal, an ultrasonic sounding method using shear polarized waves was proposed. Samples of three coal types (anthracite, lignite and hard coal) were tested. The research results show that, in contrast to the shear wave velocity, the shear wave amplitude is extremely sensitive to the formation of new cracks at the early stages of cyclic freezing–thawing. Tests also show an inverse correlation between coal compressive strength and its tendency to form cracks under temperature impacts; shear wave attenuation increases more sharply in high-rank coals after the first freezing cycle. Spectral analysis of the received signals also confirmed significant crack formation in anthracite after the first freeze–thaw cycle. The initial anisotropy was determined, and its decrease with an increase in the number of freeze–thaw cycles was shown. The data obtained forms an experimental basis for the development of new approaches to preserve coal consumer properties during storage and transportation under severe natural and climatic conditions.
- 20 June 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 7
Kaiser effect performance in anthracite as an indicator of the rock resistance to cryo-thermal treatment
The article presents the experimental studies into the stress memory in acoustic emission (Kaiser effect) in anthracite samples subjected to different number of freeze-thaw cycles. All in all, 6 groups of relatively uniform samples were tested; one group (0) was a reference set unexposed to cryo-thermal effects; the number of a group conformed with the number of treatment cycles. After the cryo-thermal action, all samples were subjected by two cycles of mechanical loading up to maximum stresses of 10 and 14 MPa, respectively. During a loading cycle, acoustic emission activity of a sample was measured, and the Kaiser effect in the second cycle of loading was assessed by two characteristics. These characteristics were the factor of retention FR of the stress memory, or the ratio of the stress of emission initiation in the second cycle to the maximal stress of the first cycle, and the index Δ, or the ratio of the averaged acoustic emission activities before and after the moment of the Kaiser effect. The values of FR and Δ are obtained and analyzed as functions of the number of anthracite freeze-thaw cycles. The value of FR drops but Δ grows with increasing cryogenic disintegration of coal. The maximal change in FR and Δ, and, accordingly, the highest dynamics of damage in anthracite takes place in the first cycles of cryo-thermal treatment.
- 20 June 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 7
Kaiser effect performance in anthracite as an indicator of the rock resistance to cryo-thermal treatment
The article presents the experimental studies into the stress memory in acoustic emission (Kaiser effect) in anthracite samples subjected to different number of freeze-thaw cycles. All in all, 6 groups of relatively uniform samples were tested; one group (0) was a reference set unexposed to cryo-thermal effects; the number of a group conformed with the number of treatment cycles. After the cryo-thermal action, all samples were subjected by two cycles of mechanical loading up to maximum stresses of 10 and 14 MPa, respectively. During a loading cycle, acoustic emission activity of a sample was measured, and the Kaiser effect in the second cycle of loading was assessed by two characteristics. These characteristics were the factor of retention FR of the stress memory, or the ratio of the stress of emission initiation in the second cycle to the maximal stress of the first cycle, and the index Δ, or the ratio of the averaged acoustic emission activities before and after the moment of the Kaiser effect. The values of FR and Δ are obtained and analyzed as functions of the number of anthracite freeze-thaw cycles. The value of FR drops but Δ grows with increasing cryogenic disintegration of coal. The maximal change in FR and Δ, and, accordingly, the highest dynamics of damage in anthracite takes place in the first cycles of cryo-thermal treatment.
- 1 January 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- Vol. 4
About features of ultrasonic measurements in coal samples using shear elastic waves
- 1 January 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- Vol. 4
About features of ultrasonic measurements in coal samples using shear elastic waves