Fakhrozi Che Ani
Research Subjects
Fakhrozi Che Ani has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Zulkifly Abdullah
School of Mechanical Engineering, Engineering Campus, Universiti Sains Malaysia, Nibong Tebal, Malaysia
8 shared publications - Chu Yee Khor
Faculty of Mechanical Engineering & Technology, Universiti Malaysia Perlis (UniMAP), Arau 02600, Perlis, Malaysia
7 shared publications - Norinsan Kamil Othman
Department of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Malaysia
5 shared publications A. Jalar
Universiti Kebangsaan Malaysia
4 shared publications- Maria Abu Bakar
Institute of Microengineering and Nanoelectronics, Universiti Kebangsaan Malaysia, Bangi, Malaysia
3 shared publications - Mohamad Riduwan Ramli
School of Materials and Mineral Resources Engineering Universiti Sains Malaysia, Engineering Campus Penang Malaysia
3 shared publications
Latest Publications
- 20 October 2022
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 35 (3) , 166-174
Numerical modelling of the delamination in multi-layered ceramic capacitor during the thermal reflow process
Purpose: This paper aims to study the interfacial delamination found in the boundary of the copper/copper-epoxy layers of a multi-layer ceramic capacitor. Design/methodology/approach: The thermal reflow process of the capacitor assembly and the crack propagation from the initial micro voids presented in the boundary, and later manifested into delamination, were numerically simulated. Besides, the cross section of the capacitor assembly was inspected for delamination cracks and voids using a scanning electronic microscope. Findings: Interfacial delamination in the boundary of copper/copper-epoxy layers was caused by the thermal mismatch and growth of micro voids during the thermal reflow process. The maximum deformation on the capacitor during reflow was 2.370 µm. It was found that a larger void would induce higher vicinity stress, mode I stress intensity factor, and crack elongation rate. Moreover, the crack extension increased with the exerted deformation until 0.3 µm, before saturating at the peak crack extension of around 0.078 µm. Practical implications: The root cause of interfacial delamination issues in capacitors due to thermal reflow has been identified, and viable solutions proposed. These can eliminate the additional manufacturing cost and lead time incurred in identifying and tackling the issues; as well as benefit end-users, by promoting the electronic device reliability and performance. Originality/value: To the best of the authors’ knowledge, the mechanism of delamination occurrence in a capacitor during has not been reported to date. The parametric variation analysis of the void size and deformation on the crack growth has never been conducted.
- 20 October 2022
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 35 (3) , 166-174
Numerical modelling of the delamination in multi-layered ceramic capacitor during the thermal reflow process
Purpose: This paper aims to study the interfacial delamination found in the boundary of the copper/copper-epoxy layers of a multi-layer ceramic capacitor. Design/methodology/approach: The thermal reflow process of the capacitor assembly and the crack propagation from the initial micro voids presented in the boundary, and later manifested into delamination, were numerically simulated. Besides, the cross section of the capacitor assembly was inspected for delamination cracks and voids using a scanning electronic microscope. Findings: Interfacial delamination in the boundary of copper/copper-epoxy layers was caused by the thermal mismatch and growth of micro voids during the thermal reflow process. The maximum deformation on the capacitor during reflow was 2.370 µm. It was found that a larger void would induce higher vicinity stress, mode I stress intensity factor, and crack elongation rate. Moreover, the crack extension increased with the exerted deformation until 0.3 µm, before saturating at the peak crack extension of around 0.078 µm. Practical implications: The root cause of interfacial delamination issues in capacitors due to thermal reflow has been identified, and viable solutions proposed. These can eliminate the additional manufacturing cost and lead time incurred in identifying and tackling the issues; as well as benefit end-users, by promoting the electronic device reliability and performance. Originality/value: To the best of the authors’ knowledge, the mechanism of delamination occurrence in a capacitor during has not been reported to date. The parametric variation analysis of the void size and deformation on the crack growth has never been conducted.
- 11 March 2021
- Published by Springer Nature
- p. 351-357
Effect of Potting Encapsulation on Crack Formation and Propagation in Electronic Package
- 11 March 2021
- Published by Springer Nature
- p. 351-357
Effect of Potting Encapsulation on Crack Formation and Propagation in Electronic Package
- 11 March 2021
- Published by Springer Nature
- p. 309-314
Effect of Moisture Content on Crack Formation During Reflow Soldering of Ball Grid Array (BGA) Component
- 11 March 2021
- Published by Springer Nature
- p. 309-314
Effect of Moisture Content on Crack Formation During Reflow Soldering of Ball Grid Array (BGA) Component
- 18 February 2019
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 31 (1) , 52-67
Corrosion characterization of Sn-Zn solder: a review
Purpose: The purpose of this paper is to review and examine three of the most common corrosion characterization techniques specifically on Sn-Zn solders. The discussion will highlight the configurations and recent developments on each of the compiled characterization techniques of potentiodynamic polarization, potentiostatic polarization and electrochemical impedance spectroscopy (EIS).Design/methodology/approach: The approach will incorporate a literature review of previous works related to the experimental setups and common parameters.Findings: The potentiostatic polarization, potentiodynamic polarization and EIS were found to provide crucial and vital information on the corrosion properties of Sn-Zn solders. Accordingly, this solder relies heavily on the amount of Zn available because of the inability to produce the intermetallic compound in between the elements. Further, the excellent mechanical properties and low melting temperature of the Sn-Zn solder is undeniable, however, the limitations regarding corrosion resistance present opportunities in furthering research in this field to identify improvements. This is to ensure that the corrosion performance can be aligned with the outstanding mechanical properties. The review also identified and summarized the advantages, recent trends and important findings in this field.Originality/value: The unique challenges and future research directions regarding corrosion measurement in Sn-Zn solders were shown to highlight the rarely discussed risks and problems in the reliability of lead-free soldering. Many prior reviews have been undertaken of the Sn-Zn system, but limited studies have investigated the corrosive properties. Therefore, this review focuses on the corrosive characterizations of the Sn-Zn alloy system.
- 18 February 2019
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 31 (1) , 52-67
Corrosion characterization of Sn-Zn solder: a review
Purpose: The purpose of this paper is to review and examine three of the most common corrosion characterization techniques specifically on Sn-Zn solders. The discussion will highlight the configurations and recent developments on each of the compiled characterization techniques of potentiodynamic polarization, potentiostatic polarization and electrochemical impedance spectroscopy (EIS).Design/methodology/approach: The approach will incorporate a literature review of previous works related to the experimental setups and common parameters.Findings: The potentiostatic polarization, potentiodynamic polarization and EIS were found to provide crucial and vital information on the corrosion properties of Sn-Zn solders. Accordingly, this solder relies heavily on the amount of Zn available because of the inability to produce the intermetallic compound in between the elements. Further, the excellent mechanical properties and low melting temperature of the Sn-Zn solder is undeniable, however, the limitations regarding corrosion resistance present opportunities in furthering research in this field to identify improvements. This is to ensure that the corrosion performance can be aligned with the outstanding mechanical properties. The review also identified and summarized the advantages, recent trends and important findings in this field.Originality/value: The unique challenges and future research directions regarding corrosion measurement in Sn-Zn solders were shown to highlight the rarely discussed risks and problems in the reliability of lead-free soldering. Many prior reviews have been undertaken of the Sn-Zn system, but limited studies have investigated the corrosive properties. Therefore, this review focuses on the corrosive characterizations of the Sn-Zn alloy system.
- 29 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (1-4) , 717-733
The influence of Fe2O3 nano-reinforced SAC lead-free solder in the ultra-fine electronics assembly
- 29 January 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (1-4) , 717-733
The influence of Fe2O3 nano-reinforced SAC lead-free solder in the ultra-fine electronics assembly
- Open Access
- 2 May 2017
- Published by Elsevier in Procedia Engineering
- Vol. 184, 625-630
Stress Analysis of a Stretchable Electronic Circuit
- 2 May 2017
- Published by Elsevier in Procedia Engineering
- Vol. 184, 625-630
Open AccessStress Analysis of a Stretchable Electronic Circuit
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1885, 020063
Influence of solder joint length to the mechanical aspect during the thermal stress analysis
Solder joint is an important interconnector in surface mount technology (SMT) assembly process. The real time stress, strain and displacement of the solder joint is difficult to observe and assess the experiment. To tackle these problems, simulation analysis was employed to study the von Mises stress, strain and displacement in the thermal stress analysis by using Finite element based software. In this study, a model of leadless electronic package was considered. The thermal stress analysis was performed to investigate the effect of the solder length to those mechanical aspects. The simulation results revealed that solder length gives significant effect to the maximum von Mises stress to the solder joint. Besides, changes in solder length also influence the displacement of the solder joint in the thermal environment. The increment of the solder length significantly reduces the von Mises stress and strain on the solder joint. Thus, the understanding of the physical parameter for solder joint is important for engineer prior to designing the solder joint of the electronic component.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1885, 020063
Influence of solder joint length to the mechanical aspect during the thermal stress analysis
Solder joint is an important interconnector in surface mount technology (SMT) assembly process. The real time stress, strain and displacement of the solder joint is difficult to observe and assess the experiment. To tackle these problems, simulation analysis was employed to study the von Mises stress, strain and displacement in the thermal stress analysis by using Finite element based software. In this study, a model of leadless electronic package was considered. The thermal stress analysis was performed to investigate the effect of the solder length to those mechanical aspects. The simulation results revealed that solder length gives significant effect to the maximum von Mises stress to the solder joint. Besides, changes in solder length also influence the displacement of the solder joint in the thermal environment. The increment of the solder length significantly reduces the von Mises stress and strain on the solder joint. Thus, the understanding of the physical parameter for solder joint is important for engineer prior to designing the solder joint of the electronic component.
- 1 January 2017
- Published by AIP Publishing
Investigation of corrosion on SAC 305, SAC 0307 and SAC 0307-0.03 P-0.005 Ni solder paste alloys in simulated body fluid (SBF)
The electrochemical migration (ECM) behaviour of SAC 305, SAC 0307 and SAC 0307-0.03 P-0.005 Ni has been investigated by using simulated body fluid (SBF) solution. Water drop test (WDT) was performed to compute the mean-time-to-failure (MTTF) of each sample while its electrical behaviour was examined using four-point probe test station. The microstructure of each solder paste alloy was observed using field emission scanning electron microscope (FESEM) with energy dispersive X-ray spectroscopy (EDX) to analyse the elemental composition of the solder alloy. The MTTF result shows that SAC 305 has the fastest time-to-failure (TTF) due to short circuit. The corrosion susceptibility of SAC 305 was higher compared with SAC 0307-0.03P-0.005Ni. This was because of the influence of dopant phosphorus and nickel incorporation in the SAC 0307-0.03 P-0.005 Ni. The four point-probe test station reveals that SAC 305 is a good electric conductor whilst SAC 0307-0.03 P-0.005 Ni is a poor electric conductor. The rate of dendritic growth was influenced by the alloying element of the solder. Therefore, SAC 0307-0.03 P-0.005 Ni have a good corrosion resistance in SBF medium.
- 1 January 2017
- Published by AIP Publishing
Investigation of corrosion on SAC 305, SAC 0307 and SAC 0307-0.03 P-0.005 Ni solder paste alloys in simulated body fluid (SBF)
The electrochemical migration (ECM) behaviour of SAC 305, SAC 0307 and SAC 0307-0.03 P-0.005 Ni has been investigated by using simulated body fluid (SBF) solution. Water drop test (WDT) was performed to compute the mean-time-to-failure (MTTF) of each sample while its electrical behaviour was examined using four-point probe test station. The microstructure of each solder paste alloy was observed using field emission scanning electron microscope (FESEM) with energy dispersive X-ray spectroscopy (EDX) to analyse the elemental composition of the solder alloy. The MTTF result shows that SAC 305 has the fastest time-to-failure (TTF) due to short circuit. The corrosion susceptibility of SAC 305 was higher compared with SAC 0307-0.03P-0.005Ni. This was because of the influence of dopant phosphorus and nickel incorporation in the SAC 0307-0.03 P-0.005 Ni. The four point-probe test station reveals that SAC 305 is a good electric conductor whilst SAC 0307-0.03 P-0.005 Ni is a poor electric conductor. The rate of dendritic growth was influenced by the alloying element of the solder. Therefore, SAC 0307-0.03 P-0.005 Ni have a good corrosion resistance in SBF medium.
- 1 July 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 669, 178-186
Hardness profiles of Sn-3.0Ag-0.5Cu-TiO2 composite solder by nanoindentation
- 1 July 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 669, 178-186
Hardness profiles of Sn-3.0Ag-0.5Cu-TiO2 composite solder by nanoindentation