KUKenjiro Uesugi

Kenjiro Uesugi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kenjiro Uesugi has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Semipolar (112¯2)$\left(\right. 11 \bar{2} 2 \left.\right)$ AlGaN‐Based Multiple Quantum Wells in the Far‐UVC Region on Face‐to‐Face Annealed Sputter‐Deposited AlN

    by Kensei Oya, Ryota Akaike, Kenjiro Uesugi, Hiroki Yasunaga, Takao Nakamura, Hideto Miyake

    Semipolar AlGaN has been explored as a promising candidate for enhancing the internal quantum efficiency and the light extraction efficiency of far‐ultraviolet C light‐emitting diodes (far‐UVC LEDs). The crystallinity of AlN has been significantly improved through face‐to‐face annealing. However, achieving a sufficiently flat surface for AlN remains challenging. Additionally, previous studies have reported variability in the orientation of AlN films sputtered onto m ‐plane sapphire. Herein, sputtering conditions are systematically investigated to optimize the deposition of AlN on m ‐plane sapphire substrates prepared by combining sputtering with face‐to‐face annealing. By optimizing the sputtering temperature, single‐domain AlN templates are successfully obtained with X‐ray rocking curve full width at half‐maximum (FWHM) values of ≈500 arcsec along the and 900 arcsec along the . Furthermore, the epitaxial growth of semipolar AlN and AlGaN multiple quantum wells (MQWs) is investigated using metalorganic vapor phase epitaxy. The growth temperature is optimized to achieve AlN layers with a reduced root‐mean‐square (RMS) roughness of less than 1 nm. MQWs exhibit higher photoluminescence efficiency at a higher growth temperature.


  • Open Access

    Impacts of homoepitaxial AlN thickness on the qualities of AlGaN QWs fabricated on the face-to-face annealed sputter-deposited AlN templates

    by Ryota Akaike, Kenjiro Uesugi, Kohei Shima, Shigefusa F. Chichibu, Akira Uedono, Takao Nakamura, Hideto Miyake

    AlGaN quantum wells (QWs) emitting at 265 nm were fabricated on face-to-face annealed sputter-deposited AlN (FFA Sp-AlN) templates with n-AlGaN and different homoepitaxial AlN thicknesses (200–2000 nm) by metalorganic vapor phase epitaxy (MOVPE). Thicker MOVPE-AlN led to higher dislocation densities. The type and concentration of vacancies in n-AlGaN, as well as the photoluminescence efficiencies and time-resolved photoluminescence lifetimes of the QWs were nearly unchanged regardless of the MOVPE-AlN thickness, suggesting nearly identical internal quantum efficiencies. The results prove high-quality AlGaN QW growth with only 200 nm thick MOVPE-AlN, resulting in reduced total thickness of AlN by using FFA Sp-AlN.

  • Open Access

    Crystal orientation control of a-plane AlN films on r-plane sapphire fabricated by sputtering and high-temperature annealing

    by Yuki Ogawa, Ryota Akaike, Jiei Hayama, Kenjiro Uesugi, Kanako Shojiki, Toru Akiyama, Takao Nakamura, Hideto Miyake

    Face-to-face annealed and sputter-deposited aluminum nitride (FFA Sp-AlN) has potential in deep-ultraviolet light-emitting devices. Herein, the effects of the substrate off-cut angle (θsub) from an r-plane sapphire toward the c-axis projection direction and sputtering temperature (Tsp) on the crystallinity and surface morphology of a-plane AlN films are investigated. Increasing θsub in the minus-off direction, which occurs when the substrate surface approaches the sapphire c-plane, and lowering Tsp suppress the mixing of anomalous non-a-direction oriented domains. This reduced mixing enhances the surface flatness and crystallinity of a-plane FFA Sp-AlN. Moreover, the c-axis direction of the a-plane AlN film is inverted depending on the substrate off-cut angle. Ab initio calculations indicate that the interface stability between the r-plane sapphire substrate and the a-plane AlN film can explain the dependence of the crystallinity and c-axis orientation of FFA Sp-AlN on the surface off-cut of the r-plane sapphire.


  • Open Access

    230 nm wavelength range far-UVC LED with low Al-composition differentiation between well and barrier layers of MQWs

    by Kenjiro Uesugi, Ryota Akaike, Shuhei Ichikawa, Takao Nakamura, Kazunobu Kojima, Masahiko Tsuchiya, Hideto Miyake

    Reducing the average Al composition of Al x Ga1−x N/Al y Ga1−y N multiple quantum wells (MQWs) is an effective approach to increase the current injection efficiencies of far-UV-C LEDs (far-UVC LEDs). A reduction can be realized by decreasing the Al-composition differentiation between the well and barrier layers. Compared to conventional MQWs, a 230 nm wavelength far-UVC LED equipped with a single-Al-composition and a 39 nm thick light-emitting layer exhibits a higher external quantum efficiency (EQE). The EQE of far-UVC LEDs with low Al-composition differentiation (∼1%) is enhanced to approximately 0.6% and 1.4% under continuous wave operations at 230 nm and 236 nm wavelengths, respectively.


  • Open Access

    Optical characterization of point defects on internal quantum efficiency in AlGaN quantum wells grown on face-to-face-annealed sputtered AlN templates

    by Satoshi Kurai, Megumi Fujii, Yuta Ohnishi, Ryota Oshimura, Kosuke Inai, Kunio Himeno, Narihito Okada, Kenjiro Uesugi, Hideto Miyake, Yoichi Yamada

    The correlation between the internal quantum efficiency (IQE) and the effective diffusion length estimated by the cathodoluminescence intensity line profile near the dark spots, including the effect of non-radiative recombination due to point defects, was experimentally clarified for AlGaN multiple quantum wells (MQWs) on face-to-face annealed (FFA) sputter-deposited AlN templates with different IQEs and similar dislocation densities. The IQEs, which were determined by temperature- and excitation-power-dependent photoluminescence measurements, were independent of the dark spot densities and increased with increasing effective diffusion length (Leff) estimated from the cathodoluminescence line profile analysis. These results suggested that the IQEs of the MQW/FFA samples were governed by the point defect density. The fitting results for the relationship between IQE and Leff and for that between IQE and Cmax explained the experimental results qualitatively.


  • Open Access

    263 nm wavelength UV-C LED on face-to-face annealed sputter-deposited AlN with low screw- and mixed-type dislocation densities

    by Kenjiro Uesugi, Shigeyuki Kuboya, Kanako Shojiki, Shiyu Xiao, Takao Nakamura, Masataka Kubo, Hideto Miyake

    Regarding deep-ultraviolet optical device applications, face-to-face annealed sputter-deposited AlN (FFA Sp-AlN) is a promising alternative to the conventional metalorganic vapor phase epitaxy (MOVPE)-prepared AlN templates on sapphire substrates. However, FFA Sp-AlN tends to exhibit AlGaN growth-related hillock generation and surface morphology deterioration. In this study, we optimized the sputter-deposition conditions for AlN and MOVPE growth conditions for AlGaN to respectively reduce hillock density and size. After confirming AlGaN surface-flattening, we fabricated 263 nm wavelength UV-C LEDs on the FFA Sp-AlN and achieved maximum external quantum efficiencies of approximately 4.9% and 8.0% without and with silicone encapsulation, respectively.


  • Fabrication of AlN templates by high-temperature face-to-face annealing for deep UV LEDs

    by Kenjiro Uesugi, Hideto Miyake

    AlN templates fabricated via a combination of sputtering deposition and post-deposition high-temperature face-to-face annealing can be applied to deep-ultraviolet (DUV) light-emitting devices because of their extremely low threading dislocation density (TDD) despite their low-cost and simple fabrication process. First, this paper summarizes the overview and essential crystalline characteristics of the face-to-face annealed sputter-deposited AlN template (FFA Sp-AlN). Thereafter, recent progress in the TDD reduction of the FFA Sp-AlN and the metalorganic vapor phase epitaxy of AlN and Al x Ga 1− x N on the FFA Sp-AlN have been reviewed. The TDD of approximately 4 × 10 7 cm −2 was obtained on the sapphire substrates with an AlN film thickness of 1.2 μ m. Finally, the potential of the low-TDD FFA Sp-AlN has been discussed by demonstrating the performances of DUV light-emitting diodes fabricated on the FFA Sp-AlN.


  • Extremely high internal quantum efficiency of AlGaN-based quantum wells on face-to-face annealed sputter-deposited AlN templates

    by Hideaki Murotani, Atsushi Fujii, Ryota Oshimura, Takafumi Kusaba, Kenjiro Uesugi, Hideto Miyake, Yoichi Yamada

    This study investigated the influence of high-quality AlN templates on the internal quantum efficiency (IQE) of AlGaN-based multiple quantum wells (MQWs) using photoluminescence spectroscopy. An extremely high IQE of 90% at room temperature was obtained from MQWs on face-to-face annealed sputter-deposited AlN/sapphire templates. The dependence of efficiency curves on temperature indicated that nonradiative recombination centers were almost fully saturated under higher excitation power densities even at 400 K. Moreover, analysis of the efficiency curves using a rate equation model based on exciton recombination processes suggested that radiative recombination was the dominant recombination process even at 400 K.


  • Open Access

    Thermal strain analysis considering in-plane anisotropy for sputtered AlN on c- and a-plane sapphire under high-temperature annealing

    by Yusuke Hayashi, Kenjiro Uesugi, Kanako Shojiki, Tetsuya Tohei, Akira Sakai, Hideto Miyake

    High-temperature annealing of sputtered AlN (Sp-AlN) using a face-to-face configuration is a novel technique that has attracted considerable attention because it can reduce the threading dislocation density of Sp-AlN to 107 cm−2. However, drawbacks such as cracking, residual stress, and wafer curvature remain because of a high annealing temperature of 1700 °C. We previously developed a thermal strain analysis model that uses an elastic multilayer system to describe the elastic behavior of Sp-AlN on sapphire under high-temperature annealing. In this study, we expand this model to consider in-plane anisotropy. By performing thermal strain analysis of the curvature, strain, stress, and strain energy of c-plane AlN grown on c- and a-plane sapphire, our calculation successfully approximates the experimental results, even for an in-plane anisotropic structure. The proposed model is, therefore, useful for quantitative evaluation of the residual strain and can contribute to strain engineering of AlGaN-based deep-ultraviolet light-emitting diodes.