Karol Chilmon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Karol Chilmon has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Wioletta Jackiewicz-Rek
Politechnika Warszawska
12 shared publications - Maciej Kalinowski
Faculty of Civil Engineering, Warsaw University of Technology, 00-637 Warsaw, Poland
11 shared publications - Piotr Woyciechowski
Faculty of Civil Engineering, Warsaw University of Technology, Al. Armii Ludowej 16, 00-637 Warsaw, Poland
4 shared publications - Janusz Jarosławski
Institute of Geophysics, Polish Academy of Sciences, 01-452 Warsaw, Poland
3 shared publications - Artur Szkop
Institute of Geophysics, Polish Academy of Sciences, 01-452 Warsaw, Poland
2 shared publications - Beata Jaworska
Faculty of Civil Engineering, Warsaw University of Technology, Al. Armii Ludowej 16, 00-637 Warsaw, Poland
2 shared publications
Latest Publications
- Open Access
- 8 November 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (22) , 9978
Role of CaO Reactivity in Controlling Fresh Properties and Long-Term Strength Development of CaO-Activated GGBFS Composites
This study systematically investigates the influence of CaO reactivity on the fresh-state rheological behavior and long-term mechanical performance of GGBFS binders. Four types of industrial quicklime, characterized by distinct slaking kinetics (tmax ranging from 9 to 36 min), were used as primary activators, with dosages of 5%, 9%, and 13% by binder mass. The results reveal that CaO reactivity significantly affects water demand, yield stress, and setting times, with extremely reactive quicklime inducing the greatest increases in water demand and plastic viscosity. Setting behavior was strongly dependent on both activator content and curing environment, with less reactive limes failing to induce setting under water immersion. Compressive strength development was largely unaffected by CaO reactivity up to 120 days, but at 720 days, higher CaO contents (≥9%) contributed to significant strength gains, likely due to carbonation-induced matrix densification. These findings demonstrate that controlling CaO reactivity and dosage is essential for optimizing the workability and durability of CaO-activated slag binders.
- 8 November 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (22) , 9978
Open AccessRole of CaO Reactivity in Controlling Fresh Properties and Long-Term Strength Development of CaO-Activated GGBFS Composites
This study systematically investigates the influence of CaO reactivity on the fresh-state rheological behavior and long-term mechanical performance of GGBFS binders. Four types of industrial quicklime, characterized by distinct slaking kinetics (tmax ranging from 9 to 36 min), were used as primary activators, with dosages of 5%, 9%, and 13% by binder mass. The results reveal that CaO reactivity significantly affects water demand, yield stress, and setting times, with extremely reactive quicklime inducing the greatest increases in water demand and plastic viscosity. Setting behavior was strongly dependent on both activator content and curing environment, with less reactive limes failing to induce setting under water immersion. Compressive strength development was largely unaffected by CaO reactivity up to 120 days, but at 720 days, higher CaO contents (≥9%) contributed to significant strength gains, likely due to carbonation-induced matrix densification. These findings demonstrate that controlling CaO reactivity and dosage is essential for optimizing the workability and durability of CaO-activated slag binders.
- Open Access
- 25 October 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 23
The effect of CaO properties on the early volume change behavior, compressive strength and microstructure of CaO-activated GGBFS composites
- 25 October 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 23
Open AccessThe effect of CaO properties on the early volume change behavior, compressive strength and microstructure of CaO-activated GGBFS composites
- 16 October 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 498
From waste to function: Ground walnut shells as a reactive additive for heavy metal removal in pervious concrete
- 16 October 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 498
From waste to function: Ground walnut shells as a reactive additive for heavy metal removal in pervious concrete
- Open Access
Photocatalytically Induced Degradation of Nano-TiO2-Modified Paint Coatings Under Low-Radiation Conditions
Photocatalytic coatings incorporating nano-TiO2 have emerged as effective solutions for air purification, utilizing solar radiation to degrade airborne pollutants. However, the long-term stability of such coatings, particularly those based on organic binders, remains a concern due to their susceptibility to photocatalytic-driven degradation. This study investigates the effects of low-intensity UV-A irradiation (1–10 W/m2) on acrylic-based photocatalytic coatings’ structural integrity and air purification performance. The findings reveal that significant binder decomposition occurs even under low irradiation conditions—comparable to natural sunlight exposure in Northern and Central Europe during autumn and winter. The surface porosity increased from 2.28% to 9.09% due to polymer degradation, exposing more nano-TiO2 particles and enhancing NO removal efficiency from approximately 120 µg/hm2 to 360 µg/hm2 under UV-A irradiation (1 W/m2). However, this process also resulted in benzene emissions reaching approximately five ppb, raising concerns about secondary pollution and the potential release of nano-TiO2 due to polymer matrix disintegration. These findings highlight the need for optimized coating formulations that balance photocatalytic efficiency with long-term material stability, mitigating the environmental and health risks associated with secondary pollutant emissions.
Open AccessPhotocatalytically Induced Degradation of Nano-TiO2-Modified Paint Coatings Under Low-Radiation Conditions
Photocatalytic coatings incorporating nano-TiO2 have emerged as effective solutions for air purification, utilizing solar radiation to degrade airborne pollutants. However, the long-term stability of such coatings, particularly those based on organic binders, remains a concern due to their susceptibility to photocatalytic-driven degradation. This study investigates the effects of low-intensity UV-A irradiation (1–10 W/m2) on acrylic-based photocatalytic coatings’ structural integrity and air purification performance. The findings reveal that significant binder decomposition occurs even under low irradiation conditions—comparable to natural sunlight exposure in Northern and Central Europe during autumn and winter. The surface porosity increased from 2.28% to 9.09% due to polymer degradation, exposing more nano-TiO2 particles and enhancing NO removal efficiency from approximately 120 µg/hm2 to 360 µg/hm2 under UV-A irradiation (1 W/m2). However, this process also resulted in benzene emissions reaching approximately five ppb, raising concerns about secondary pollution and the potential release of nano-TiO2 due to polymer matrix disintegration. These findings highlight the need for optimized coating formulations that balance photocatalytic efficiency with long-term material stability, mitigating the environmental and health risks associated with secondary pollutant emissions.
- Open Access
- 21 February 2025
- Published by MDPI AG in Purification
- Vol. 1 (1) , 1
Predictive Modeling of Air Purification Efficiency in Nano-TiO2-Modified Photocatalytic Cementitious Composites Using High-Resolution EDS Mapping and Mercury Intrusion Porosimetry
This study investigates the relationship between surface properties and microstructural characteristics of photocatalytic composites and their impact on air purification efficiency. High-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and mercury intrusion porosimetry (MIP) were employed to analyze photocatalyst distribution and pore structure quantitatively. The findings demonstrated a strong correlation between TiO2 coverage on the photoactive surface and NO removal rates and between pore structure characteristics and NO2 generation rates. Two predictive models were developed to link NOx removal rates with photocatalytic cementitious mortars’ surface and structural properties. A stepwise regression approach produced a second-degree polynomial model with an adjusted R2 of 0.98 and a Mean Absolute Percentage Error (MAPE) of 8.34%, indicating high predictive accuracy. The results underscore the critical role of uniform photocatalyst distribution and optimized pore structure in enhancing NOx removal efficiency while promoting the generation of desirable products (NO3−) and minimizing the formation of undesirable byproducts (NO2).
- 21 February 2025
- Published by MDPI AG in Purification
- Vol. 1 (1) , 1
Open AccessPredictive Modeling of Air Purification Efficiency in Nano-TiO2-Modified Photocatalytic Cementitious Composites Using High-Resolution EDS Mapping and Mercury Intrusion Porosimetry
This study investigates the relationship between surface properties and microstructural characteristics of photocatalytic composites and their impact on air purification efficiency. High-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and mercury intrusion porosimetry (MIP) were employed to analyze photocatalyst distribution and pore structure quantitatively. The findings demonstrated a strong correlation between TiO2 coverage on the photoactive surface and NO removal rates and between pore structure characteristics and NO2 generation rates. Two predictive models were developed to link NOx removal rates with photocatalytic cementitious mortars’ surface and structural properties. A stepwise regression approach produced a second-degree polynomial model with an adjusted R2 of 0.98 and a Mean Absolute Percentage Error (MAPE) of 8.34%, indicating high predictive accuracy. The results underscore the critical role of uniform photocatalyst distribution and optimized pore structure in enhancing NOx removal efficiency while promoting the generation of desirable products (NO3−) and minimizing the formation of undesirable byproducts (NO2).
- Open Access
Photocatalytic Performance of Cementitious Composites Modified with Second-Generation Nano-TiO2 Dispersions: Influence of Composition and Granulation on NOx Purification Efficiency
This study investigated the influence of the composition of photocatalytic dispersions made with second-generation nano-TiO2 on the air purification performance of photocatalytic cementitious composites. Nine mortar series were prepared, incorporating photocatalytic dispersions of variable content of nano-TiO2, dispersing agent (superplasticizer), and hydrophobic admixture. The total mass content of nano-TiO2 in investigated mortars was kept at the same level. For investigated composites, photocatalytic removal of NOx was evaluated under simulated laboratory conditions mimicking polish autumn/winter irradiation conditions. The results indicate that within the tested range of variability, the dispersion composition significantly influenced the granulation of the dispersed nano-TiO2 particles, which in turn affected the air purification performance of the composites. A predictive model was developed to account for environmental factors potentially influencing photocatalytic performance in urban environments. The model estimated that, depending on environmental conditions and photocatalytic dispersion composition, the composite’s photocatalytic layer could remove up to 1.067 g/m2 of NO2 per year in favorable environmental conditions. Photocatalytic cementitious composites can act as environmentally beneficial composites, contributing to carbon-negative construction practices and improving urban air quality. This highlights the dual benefits of offsetting embedded carbon emissions and enhancing air purification efficiency in sustainable urban infrastructure.
Open AccessPhotocatalytic Performance of Cementitious Composites Modified with Second-Generation Nano-TiO2 Dispersions: Influence of Composition and Granulation on NOx Purification Efficiency
This study investigated the influence of the composition of photocatalytic dispersions made with second-generation nano-TiO2 on the air purification performance of photocatalytic cementitious composites. Nine mortar series were prepared, incorporating photocatalytic dispersions of variable content of nano-TiO2, dispersing agent (superplasticizer), and hydrophobic admixture. The total mass content of nano-TiO2 in investigated mortars was kept at the same level. For investigated composites, photocatalytic removal of NOx was evaluated under simulated laboratory conditions mimicking polish autumn/winter irradiation conditions. The results indicate that within the tested range of variability, the dispersion composition significantly influenced the granulation of the dispersed nano-TiO2 particles, which in turn affected the air purification performance of the composites. A predictive model was developed to account for environmental factors potentially influencing photocatalytic performance in urban environments. The model estimated that, depending on environmental conditions and photocatalytic dispersion composition, the composite’s photocatalytic layer could remove up to 1.067 g/m2 of NO2 per year in favorable environmental conditions. Photocatalytic cementitious composites can act as environmentally beneficial composites, contributing to carbon-negative construction practices and improving urban air quality. This highlights the dual benefits of offsetting embedded carbon emissions and enhancing air purification efficiency in sustainable urban infrastructure.
- Open Access
Carbon-Negative Nano-TiO2-Modified Photocatalytic Cementitious Composites: Removal of Airborne Pollutants (NOx and O3) and Its Impact on CO2 Footprint
This study explores the development and performance of photocatalytic cementitious composites modified with nano-TiO2 to address urban air quality and sustainability challenges. Nine mortar series were prepared, incorporating binders with varying carbon footprints and mass contents across different series. The interplay between the fundamental (abrasion resistance) and functional (air purification efficiency) properties of the composites’ surfaces and interfaces was investigated. The photocatalytic removal of airborne pollutants, specifically nitrogen oxides (NOx) and ozone (O3), was evaluated under simulated environmental conditions. The variations in binder composition influenced the composites’ overall initial carbon footprint and air purification efficiency. The assessment revealed a possible net decrease in carbon emissions over the life cycle of the composite due to the removal of ozone (greenhouse gas) and its precursor—NOx, highlighting the potential of photocatalytic cementitious composites for dual environmental benefits in an urban environment, emphasizing the critical role of surface and interface engineering in achieving carbon-negative composites.
Open AccessCarbon-Negative Nano-TiO2-Modified Photocatalytic Cementitious Composites: Removal of Airborne Pollutants (NOx and O3) and Its Impact on CO2 Footprint
This study explores the development and performance of photocatalytic cementitious composites modified with nano-TiO2 to address urban air quality and sustainability challenges. Nine mortar series were prepared, incorporating binders with varying carbon footprints and mass contents across different series. The interplay between the fundamental (abrasion resistance) and functional (air purification efficiency) properties of the composites’ surfaces and interfaces was investigated. The photocatalytic removal of airborne pollutants, specifically nitrogen oxides (NOx) and ozone (O3), was evaluated under simulated environmental conditions. The variations in binder composition influenced the composites’ overall initial carbon footprint and air purification efficiency. The assessment revealed a possible net decrease in carbon emissions over the life cycle of the composite due to the removal of ozone (greenhouse gas) and its precursor—NOx, highlighting the potential of photocatalytic cementitious composites for dual environmental benefits in an urban environment, emphasizing the critical role of surface and interface engineering in achieving carbon-negative composites.
- Open Access
Effect of Cement Substitution with Mineral Fillers on NOx Air-Purification Efficiency and Photocatalytic Reaction Selectivity of Nano-TiO2-Modified Cementitious Composites
This research investigated the properties of photocatalytic cementitious composites, including their air-purification efficiency. A method of characterizing the removal of airborne pollutants (nitrogen oxides), simulating the actual NOx concentration and irradiation conditions in Warsaw, Poland, in the autumn/winter season was established. The study analyzed the impact of changes in the composition of cement mortars—partial substitution of the binder with mineral fillers—on the properties of the external photoactive surface of the composite. The designed experimental plan included both quantitative and qualitative variables (type and amount of fillers used). It was found that the photocatalytic performance of the composite was correlated with its pore total content and pore size distribution—the higher the content of mineral fillers, the lower the porosity and the less effective its photocatalytic properties. The selectivity of the photocatalytic NOx reactions also deteriorated as the content of the mineral fillers increased. The study confirmed the validity of increasing the binder content in cementitious composites to enhance their photocatalytic performance.
Open AccessEffect of Cement Substitution with Mineral Fillers on NOx Air-Purification Efficiency and Photocatalytic Reaction Selectivity of Nano-TiO2-Modified Cementitious Composites
This research investigated the properties of photocatalytic cementitious composites, including their air-purification efficiency. A method of characterizing the removal of airborne pollutants (nitrogen oxides), simulating the actual NOx concentration and irradiation conditions in Warsaw, Poland, in the autumn/winter season was established. The study analyzed the impact of changes in the composition of cement mortars—partial substitution of the binder with mineral fillers—on the properties of the external photoactive surface of the composite. The designed experimental plan included both quantitative and qualitative variables (type and amount of fillers used). It was found that the photocatalytic performance of the composite was correlated with its pore total content and pore size distribution—the higher the content of mineral fillers, the lower the porosity and the less effective its photocatalytic properties. The selectivity of the photocatalytic NOx reactions also deteriorated as the content of the mineral fillers increased. The study confirmed the validity of increasing the binder content in cementitious composites to enhance their photocatalytic performance.
- Open Access
Influence of Coarse Aggregate Exposure on Air Purification Efficiency in Photocatalytic Cement Composites
This study investigated how the surface characteristics of photocatalytic cementitious composites influenced the effectiveness of air purification from nitrogen oxides (NOx), with a particular focus on the impact of coarse aggregate exposure on the photoactive surface. Air purification efficiency tests were conducted using a custom-developed procedure that simulated NOx concentrations and UV irradiance typical of autumn and winter conditions in Warsaw, Poland. The findings revealed that the extent of exposed coarse aggregate on the photoactive surface significantly affected photocatalytic efficiency, reducing the overall NO removal rate by up to 50% compared to the reference value. The use of hydration retarders modified the surface characteristics of the photocatalytic cement matrix, enhancing its photoactive potential. The observed decline in photocatalytic efficiency in composites with exposed coarse aggregate was attributed to the coarse aggregate’s limited ability to retain nanometric photocatalyst particles, which reduced the overall TiO2 content in the composite’s near-surface layer. Nevertheless, cementitious composites incorporating a first-generation photocatalyst exhibited substantial photocatalytic activity, achieving NO removal rates of up to 340 µg/m2·h for non-exposed variants and up to 175 µg/m2·h for variants with exposed aggregate. These results demonstrated their functionality even under low-intensity UV-A irradiation (1 W/m2), making them suitable for environments with limited sunlight exposure.
Open AccessInfluence of Coarse Aggregate Exposure on Air Purification Efficiency in Photocatalytic Cement Composites
This study investigated how the surface characteristics of photocatalytic cementitious composites influenced the effectiveness of air purification from nitrogen oxides (NOx), with a particular focus on the impact of coarse aggregate exposure on the photoactive surface. Air purification efficiency tests were conducted using a custom-developed procedure that simulated NOx concentrations and UV irradiance typical of autumn and winter conditions in Warsaw, Poland. The findings revealed that the extent of exposed coarse aggregate on the photoactive surface significantly affected photocatalytic efficiency, reducing the overall NO removal rate by up to 50% compared to the reference value. The use of hydration retarders modified the surface characteristics of the photocatalytic cement matrix, enhancing its photoactive potential. The observed decline in photocatalytic efficiency in composites with exposed coarse aggregate was attributed to the coarse aggregate’s limited ability to retain nanometric photocatalyst particles, which reduced the overall TiO2 content in the composite’s near-surface layer. Nevertheless, cementitious composites incorporating a first-generation photocatalyst exhibited substantial photocatalytic activity, achieving NO removal rates of up to 340 µg/m2·h for non-exposed variants and up to 175 µg/m2·h for variants with exposed aggregate. These results demonstrated their functionality even under low-intensity UV-A irradiation (1 W/m2), making them suitable for environments with limited sunlight exposure.
- Open Access
Organic and Inorganic Modifications to Increase the Efficiency in Immobilization of Heavy Metal (Zn) in Cementitious Composites—The Impact of Cement Matrix Pore Network Characteristics
This research investigated the properties of modified cementitious composites including water purification from heavy metal—zinc. A new method for characterizing the immobilization properties of tested modifiers was established. Several additions had their properties investigated: biochar (BC), active carbon (AC), nanoparticulate silica (NS), copper slag (CS), iron slag (EAFIS), crushed hazelnut shells (CHS), and lightweight sintered fly ash aggregate (LSFAA). The impact of modifiers on the mechanical and rheological properties of cementitious composites was also studied. It was found that considered additions had a significantly different influence over the investigated properties. The addition of crushed hazelnut shells, although determined as an effective immobilization modifier, significantly deteriorated the mechanical performance of the composite as well as its rheological properties. Modification by iron slag allowed for a significant increase in immobilization properties (five-fold compared to the reference series) without a substantial impact on other properties. The negative effect on immobilization efficiency was observed for nanoparticulate silica modification due to its sealing effect on the pore network of the cement matrix. The capillary pore content in the cement matrix was identified as a parameter significantly influencing the immobilization potential of most considered modifications, except biochar and active carbon.
Open AccessOrganic and Inorganic Modifications to Increase the Efficiency in Immobilization of Heavy Metal (Zn) in Cementitious Composites—The Impact of Cement Matrix Pore Network Characteristics
This research investigated the properties of modified cementitious composites including water purification from heavy metal—zinc. A new method for characterizing the immobilization properties of tested modifiers was established. Several additions had their properties investigated: biochar (BC), active carbon (AC), nanoparticulate silica (NS), copper slag (CS), iron slag (EAFIS), crushed hazelnut shells (CHS), and lightweight sintered fly ash aggregate (LSFAA). The impact of modifiers on the mechanical and rheological properties of cementitious composites was also studied. It was found that considered additions had a significantly different influence over the investigated properties. The addition of crushed hazelnut shells, although determined as an effective immobilization modifier, significantly deteriorated the mechanical performance of the composite as well as its rheological properties. Modification by iron slag allowed for a significant increase in immobilization properties (five-fold compared to the reference series) without a substantial impact on other properties. The negative effect on immobilization efficiency was observed for nanoparticulate silica modification due to its sealing effect on the pore network of the cement matrix. The capillary pore content in the cement matrix was identified as a parameter significantly influencing the immobilization potential of most considered modifications, except biochar and active carbon.