Jan Maciejewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jan Maciejewski has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Paweł Ciężkowski
Division of Numerical Methods and Intelligent Structures, Faculty of Automotive and Construction Machinery Engineering, Warsaw University of Technology, Ludwika Narbutta 84 Street, 02-524 Warsaw, Poland
4 shared publications - Zenon Mróz
Polish Academy of Sciences
3 shared publications A. Jarzȩbowski
Institute of Fundamental Technological Research, Polish Academy of Sciences, Swietokrzyska 21, 00-049 Warsaw, Poland
2 shared publications- Sebastian Bąk
Division of Construction Machinery, Faculty of Automotive and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta St., 02-524 Warsaw, Poland
2 shared publications Tadeusz Szymczak
Motor Transport Institute
2 shared publicationsZ. Mróz
Institute of Fundamental Technological Research, Polish Academy of Sciences, ul. Świętokrzyska 21,00-049 Warsaw, Poland
2 shared publications
Latest Publications
- Open Access
- 27 February 2021
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 93 (1) , 39-50
Sliding of spherical ball on solid lubricating coating combined with wear process
In present paper we show results of ball-on-disk wear experiment of MoS2 film deposited on Ti6Al4V substrate. The ball materials is aluminum oxide. The tests are performed for different surrounding temperature conditions: 20 oC, 200 oC and 350 oC. It is shown that depth of the wear groove increases with increasing surrounding temperature. A finite element modeling approach is next developed to mimic the experimental observations of ball-on-disk wear process. It is based on the assumption of steady state condition developed during short time scale at contact region. The steady state results can next be applied to long time scale in which wear process is numerically simulated. Model results are compared with experimentally obtained wear groove and show satisfactory agreement.
- 27 February 2021
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 93 (1) , 39-50
Open AccessSliding of spherical ball on solid lubricating coating combined with wear process
In present paper we show results of ball-on-disk wear experiment of MoS2 film deposited on Ti6Al4V substrate. The ball materials is aluminum oxide. The tests are performed for different surrounding temperature conditions: 20 oC, 200 oC and 350 oC. It is shown that depth of the wear groove increases with increasing surrounding temperature. A finite element modeling approach is next developed to mimic the experimental observations of ball-on-disk wear process. It is based on the assumption of steady state condition developed during short time scale at contact region. The steady state results can next be applied to long time scale in which wear process is numerically simulated. Model results are compared with experimentally obtained wear groove and show satisfactory agreement.
- 8 February 2019
- Published by Springer Nature
- p. 250-259
The Model of Soil Compaction Process and Concept of Smart Compactor
- 8 February 2019
- Published by Springer Nature
- p. 250-259
The Model of Soil Compaction Process and Concept of Smart Compactor
- Open Access
- 14 November 2017
- Published by Springer Nature in Acta Mechanica
- Vol. 229 (2) , 475-496
Constitutive modeling of cyclic deformation of metals under strain controlled axial extension and cyclic torsion
- 14 November 2017
- Published by Springer Nature in Acta Mechanica
- Vol. 229 (2) , 475-496
Open AccessConstitutive modeling of cyclic deformation of metals under strain controlled axial extension and cyclic torsion
- 6 September 2017
- Published by Springer Nature
- p. 253-265
Study on Load Distribution in the Working Space of Lever Crusher
- 6 September 2017
- Published by Springer Nature
- p. 253-265
Study on Load Distribution in the Working Space of Lever Crusher
- 6 September 2017
- Published by Springer Nature
- p. 239-252
Evaluation of Influence of Crushing Plates Shape on “Mucharz” Sandstone Crushing Process
- 6 September 2017
- Published by Springer Nature
- p. 239-252
Evaluation of Influence of Crushing Plates Shape on “Mucharz” Sandstone Crushing Process
- Open Access
- 27 June 2017
- Published by Walter de Gruyter GmbH in Studia Geotechnica et Mechanica
- Vol. 39 (2) , 17-24
Analysis of Energy Consumption of Crushing Processes – Comparison of One-Stage and Two-Stage Processes
This paper presents experimental comparison of two machine crushing technologies: one-stage and two-stage. The study was carried on a model double-toggle jaw crusher which allows crushing forces, energy and toggle displacement to be measured. The main aim of the work was to determine the energy consumption of crushing process assuming a given level of fragmentation. Studies were performed on three rocks: granite “Strzegom”, limestone “Morawica” and sandstone “Mucharz”. The material tested had a cubic shape and average dimension of 90 mm. One-stage crushing was carried out for outlet slot er = 11 mm, and two-stage crushing for er = 24 mm and 11 mm. In the tests special design of variable profile moving jaw was used and fixed jaw was flat. The analysis of the results shows that taking into account energy consumption, it is better to use two-stage crushing process. For given materials energy consumption in the two-stage crushing process was reduced by 30%.
- 27 June 2017
- Published by Walter de Gruyter GmbH in Studia Geotechnica et Mechanica
- Vol. 39 (2) , 17-24
Open AccessAnalysis of Energy Consumption of Crushing Processes – Comparison of One-Stage and Two-Stage Processes
This paper presents experimental comparison of two machine crushing technologies: one-stage and two-stage. The study was carried on a model double-toggle jaw crusher which allows crushing forces, energy and toggle displacement to be measured. The main aim of the work was to determine the energy consumption of crushing process assuming a given level of fragmentation. Studies were performed on three rocks: granite “Strzegom”, limestone “Morawica” and sandstone “Mucharz”. The material tested had a cubic shape and average dimension of 90 mm. One-stage crushing was carried out for outlet slot er = 11 mm, and two-stage crushing for er = 24 mm and 11 mm. In the tests special design of variable profile moving jaw was used and fixed jaw was flat. The analysis of the results shows that taking into account energy consumption, it is better to use two-stage crushing process. For given materials energy consumption in the two-stage crushing process was reduced by 30%.
- 4 February 2015
- Published by Springer Nature
- p. 117-142
Experimental and Numerical Investigations of the Effects Associated to Complex Loading Combinations
- 4 February 2015
- Published by Springer Nature
- p. 117-142
Experimental and Numerical Investigations of the Effects Associated to Complex Loading Combinations
- 1 February 2014
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 51 (3-4) , 740-753
Material effects during monotonic-cyclic loading
- 1 February 2014
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 51 (3-4) , 740-753
Material effects during monotonic-cyclic loading
- 1 January 2011
- Published by Springer Nature
- p. 69-89
Critical Plane Approach to Analysis of Failure Criteria for Anisotropic Geomaterials
- 1 January 2011
- Published by Springer Nature
- p. 69-89
Critical Plane Approach to Analysis of Failure Criteria for Anisotropic Geomaterials
- 1 January 2011
- Published by Springer Nature
- p. 325-345
Analysis of Deformation and Damage Processes in Soil-Tool Interaction Problems
- 1 January 2011
- Published by Springer Nature
- p. 325-345
Analysis of Deformation and Damage Processes in Soil-Tool Interaction Problems