ISIlknur Tosun Satir

Ilknur Tosun Satir

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ilknur Tosun Satir has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synthesis and Characterization of Rosa Canina-Fe3O4/Chitosan Nanocomposite and Treatment of Safranin O Dye from Wastewater

    by Tugba Ceylan, İlknur Tosun Satır, Bediha Akmeşe

    In response to the increasing demand for environmentally friendly and cost-effective adsorbents in wastewater treatment, this study reports the green synthesis, characterization, and application of a magnetic epichlorohydrin Rosa canina (m-ECH-RC) nanocomposite for removing Safranin O (SO), a commonly used cationic dye in textile effluents. The synthesized material was characterized using Brunauer–Emmett–Teller (BET), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and zeta potential analyses to reveal its surface morphology, pore structure, functional groups, crystallinity, and colloidal stability. Adsorption performance was systematically tested under various conditions, including pH, adsorbent dose, contact time, ionic strength, and initial dye concentration. Kinetic analyses revealed that the adsorption process of Safranin O dye mainly obeys pseudo-second-order kinetics, but intraparticle and film diffusion also contribute to the process. As a result of the Isotherm analysis, it was found that the adsorption process conformed to the Langmuir model. Testing on real textile wastewater samples demonstrated a removal efficiency of 75.09% under optimized conditions. Reusability experiments further revealed that the material maintained high adsorption–desorption performance for up to five cycles, emphasizing its potential for practical use. These findings suggest that m-ECH-RC is a viable and sustainable adsorbent for treating dye-laden industrial effluents.


  • Open Access

    Sustainable Dye Removal Using Agricultural Waste: Green Synthesis of Chitosan-Immobilized Peanut Shells for AR1 Biosorption

    by Melda Bolat, İlKnur Tosun Satir

    This study delves into the exploration of novel, environmentally friendly, and economically viable chemically modified biosorbents from chitosan-immobilized peanut shells (CIPS). The aim is to efficiently remove acid red 1 dye (AR1) from wastewater. The produced biosorbents were thoroughly characterized analytically. To optimize the operating parameters, optimum conditions were determined by adsorption experiments carried out in batch and continuous systems. The study also monitored biosorption kinetics and evaluated equilibrium biosorption data with Langmuir, Freundlich, and Dubinin Radushkevich isotherm models. The biosorption potential of the developed material in a natural wastewater environment was tested. Possible biosorbent dye interactions were examined by SEM analysis. The initial pH, amount of biosorbent, initial dye concentration, foreign ion, and temperature effects of biosorption were examined in the batch system. Solution flow rate, amount of biosorbent, and desorption parameters were investigated in the continuous system. Maximum dye removal occurred at pH 2.0. The 0.2 g L-1 biosorbent achieved 84.5% AR1 dye removal. Among the applied kinetic models, the pseudo-second-order kinetic model is the one that best explains the biosorption kinetics. AR1 biosorption by immobilized biomass appears compatible with the Langmuir isotherm model. Studies carried out in a continuous system achieved 91.5% biosorption efficiency with 0.2 g L-1 biosorbent at pH 2.0. Experiments conducted to find the most suitable biosorption conditions show that biosorption depends on the initial pH, amount of biosorbent, and contact time. The biosorbent prepared in biosorption studies using real wastewater can be evaluated as a green potential candidate material for commercial-scale dye removal applications in industrial wastewater. This solution, utilizing peanut shell, an agricultural waste prepared with green synthesis, effectively removes AK1 dye due to its environmentally friendly and sustainable properties. Thus, a solution providing both economic and environmental advantages has been presented, offering reassurance in its potential.

  • Open Access

    Tarımsal Atıklar Kullanılarak Tekstil Atık Sularındaki Boyar Maddelerin Adsorpsiyonla Arıtılması

    by Bediha Akmeşe, İlknur Tosun Satır

    Tekstil endüstrisinin son yıllardaki hızlı gelişimi nedeniyle yüksek miktarda su tüketimi ve yüksek toksisiteli kimyasallar içeren atık suların çevreye salınımı, çevre kirliliği ve insan sağlığı için tehdit oluşturmaktadır. Özellikle, boyar maddeler gibi kimyasalların kanserojen, teratojen ve mutajen etkileri, su kirliliği sorununu daha da vahim hale getirmektedir. Bu çalışmada, tekstil atık sularında bulunan boyar maddelerin sulu çözeltilerden uzaklaştırılması için doğada atık olarak bulunan malzemelerin adsorban olarak kullanılabilirliği araştırılmıştır. Bu amaçla, asit kırmızısı 1 (AK1), asit mavisi 80 (AM80), parlak mavi G (PMG), safranin O (SO) ve Victoria saf mavisi BO (VSMBO) boyar maddelerinin adsorpsiyon potansiyeli incelenmiştir. Adsorban olarak yer fıstığı kabuğu, çam poleni, mandalina kabuğu, nar kabuğu, Antep fıstığı kabuğu, muz kabuğu ve bal kabağı kabuğu gibi doğada bol miktarda bulunan ve atık olarak değerlendirilebilecek malzemeler kullanılmıştır. Çalışma, iki farklı pH seviyesinde (orijinal pH ve pH=2) gerçekleştirilmiş, bu pH koşullarında adsorpsiyon verimliliği değerlendirilmiştir. Sonuç olarak pH=2’de en yüksek giderimin AK1 boyar maddesi için muz kabuğu (%86.07) ile, AM80 boyar maddesi için yer fıstığı kabuğu (%94.83) ve PMG boyar maddesi için ise nar kabuğu (%96.49) ile elde edilmiştir. Orijinal pH’da SO ve VSMBO boyar maddelerinin ise orijinal pH’da tüm adsorbanların etkili olduğu gözlemlenmiştir. Bu çalışmada, farklı pH seviyelerinin (orijinal pH ve pH=2) bu boyar maddelerin adsorpsiyon kapasiteleri üzerindeki etkisini, tek yönlü ANOVA analizi ile değerlendirilmiştir. AK1, AM80, SO ve VSM80 için anlamlı farklılıklar gözlemlenirken, PMG için anlamlı bir fark bulunmamıştır. Bu bulgular, tekstil atık sularının arıtımında çevre dostu ve düşük maliyetli çözümler sunmaktadır.

  • Open Access

    Adsorption of the Antibiotic Roxithromycin on Low-Cost Food Waste Materials: Batch and Column Studies

    by Ilknur Tosun Satir, Bediha Akmeşe

    Antibiotics are widely utilized for a variety of medical conditions. Antibiotic residues in wastewater are dangerous to all living beings. Antibiotics remain in the wastewater environment when general treatment plant technologies are employed. The literature has numerous techniques for getting rid of antibiotics. Compared to other techniques for removing contaminants in the solution environment, the adsorption method is preferred due to its benefits, such as ease of use, high efficiency, and low cost. The study investigated using the green walnut shell (GWS), a natural sorbent, as an adsorbent to discharge roxithromycin (ROX) antibiotics from the solution medium. Adsorption conditions were studied in batch and continuous systems. pH, adsorbent amount, interaction time, sorbate concentration, and salt effect parameters were investigated in the batch system. The data obtained were calculated with kinetic and isotherm models. The adsorption process has been based on the so-called pseudo-second-order kinetic model. GWS was characterized using SEM and FTIR techniques. The amount of absorbent, flow rate, and breakdown in the continuous system were explored. In the batch system, the adsorption equilibrium was set up at the solution's original pH with 0.1 g of adsorbent in 40 minutes, and 79% ROX removal was achieved. The optimum flow rate and adsorbent amount in the continuous system were determined as 0.1 mL/min and 0.3 g, respectively.


  • Bone meal and chitosan biocomposite: a new biosorbent for the removal of Victoria Blue R from wastewater

    by Ilknur Tosun Satir, Naim Ozdemir, Cigdem Donmez Gungunes

    Chitosan immobilized bone meal (CIBM) was prepared as a biosorbent and Victoria Blue R (VBR) textile dyestuff was removed from wastewater using CIBM via biosorption. For this purpose; the effect of pH, contact time, ionic strength, temperature, biosorbent amount, and initial sorbate concentration were studied in the batch system. The specific surface area, surface morphology and functional groups of CIBM were characterized using BET, SEM and FTIR techniques. In the preliminary biosorption studies with pure bone meal, the removal yield of VBR from solutions of 25 mg/L VBR prepared in pure water was found to be 40.32%, while after modification with chitosan, a removal yield of 98.69% was achieved. As a result, it was observed that the biosorption efficiency increased significantly via modification. The biosorption equilibrium was set at the original pH of the dye with a biosorbent amount of 3.00 g/L in 15 min., which are the optimum adsorption parameters of the batch biosorption process. The removal of VBR from real wastewater was investigated, and the efficiency was found to be 90.40%. Biosorption-desorption cycle was investigated for 11 cycles, and CIBM almost maintained its biosorption capacity until the ninth cycle. Kinetic, isotherm and thermodynamic models were used to analyze the data obtained from the experiments. As kinetic models, pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetic models were used along with the intraparticle diffusion model. For isotherm models, Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) models were employed. It was determined that the experimental biosorption data obey the second-order kinetic model.


  • Calcined Eggshell for Removal of Victoria Blue R Dye from Wastewater Medium by Adsorption

    by İ̇lknur Tosun Satir, Kadir Erol

    In this study, the use of calcined eggshell (CE) as an adsorbent in removing Victoria Blue R (VBR) dyestuff from the solution medium was investigated. For this purpose, pH, interaction time, adsorbate concentration, amount of adsorbent, and salt effect parameters were studied to determine the appropriate adsorption conditions. The highest adsorption yield was obtained in pH 2, 2.0 g/L adsorbent and a stirring time of 5 minutes. 97% of the dye was removed under optimum adsorption conditions. The results obtained from the experimental studies showed that the adsorption mechanism is compatible with the pseudo-second-order kinetic model and the Langmuir isotherm model. SEM and IR analyses were performed for the characterization of calcined eggshells (CE).


  • Open Access

    Investigation of the Chitosan Immobilized Eggshell for the Biosorption of Brillant Blue R Dye

    by Buket Bulut Kocabas, Ilknur Tosun Satir

    The biosorption method for controlling water pollution can be considered as an alterna-tive method for the pollution of synthetic paints. In this study, the removal of Bril-lant Blue R (BBR) dyestuff, which is a textile dyestuff, by biosorption is investigated. For this purpose, eggshell immobilized with chitosan (ESIC) is designed as a biosorbent. The biosorption mechanism was studied in batch and continuous mode. As far as the batch system is concerned, the following results have been obtained: The optimum pH 2, dye concentration 25 ppm, interaction time 60 minutes, biosorbent amount 2.0 g/L, removal real wastewater 53.28%. Regarding continuous systems, the following f low speed of 0.5 mL/min, biosorbent amount 2.0 g/L, removal real wastewater 91.01%. Also, recycle ex-periments showed that there was 24.11% loss in the biosorption capacity of ESIC for BBR dye after 7 times reuse. Obtained results were consistent with Langmuir and Freundlich isotherm models. All the results demonstrate that ESIC is a natural, recyclable and cost-effective biosorbent for BBR dye removal in wastewater. Keywords: Biosorption; BBR; Eggshell; Chitosan; Dye. DOI: 10.17350/HJSE19030000159 Full Text:


  • A novel sorbent for removal of reactive textile dye: TDPA-KCl

    by Ilknur Tosun Satır, Fatih Sayin, Tevfik Gedikbey, Sibel Tunali Akar

    The use of alunite as an adsorbent for the removal of dye was the aim of this report. Mixing the alunite with different salts may allow adsorption with higher efficiency. In the present study, the thermal decomposition product of alunite-potassium chloride mixture (TDPA-KCl) was used efficiently and inexpensively to remove Reactive Blue 49 (RB49) dye. The adsorption capacity of TDPA-KCl was found to be affected by pH, temperature, adsorbent amount, calcination temperature, dye concentration, and ionic strength. The highest RB49 adsorption yield was obtained at an initial pH of 2 and an equilibrium was reached within 20 min using 80 mg of adsorbent. The most suitable kinetic model was found as the pseudo-second-order and compatible isotherm was determined as the Langmuir model. The optimum adsorption capacity was found as 119.10 mg g−1 at 40 °C. ∆G°, ∆H°, and ∆S° values were calculated. A positive value of ∆H° stated that the adsorption is exothermic and spontaneous. In addition, ∆G° showed a more negative value when temperature was increased. Column studies indicated that TDPA-KCl could be effectively used for five cycles without any loss in its desorption potential. Breakthrough studies also supported a favorable adsorption of RB49 onto TDPA-KCl. This study showed that TDPA-KCl is a practical, efficient, and inexpensive adsorbent to remove reactive dyes from wastewater.


  • Open Access

    Adsorption of Victoria Blue R (VBR) dye on magnetic microparticles containing Fe(II)–Co(II) double salt

    by Kadir Erol, Kazım Köse, Dursun Ali Köse, Ümit Sızır, İlknur Tosun Satır, Lokman Uzun

    Magnetic microparticles have many applications in various areas today. The aim of this study was to develop hydrophobic magnetic microparticles as an alternative to traditional methods for high capacity and low cost removal of Victoria Blue R (VBR), which is valuable for industry and commercial, from wastewater and to determine the VBR adsorption ability of this adsorbent. Fe(II)–Co(II) double salt incorporated magnetic poly(2-hydroxyethyl methacrylate-N-methacryloyl-l-tryptophan) [m-poly(HEMA-MATrp)] microparticles were synthesized and used as adsorbent. These microparticles were synthesized in aqueous dispersion medium via microemulsion polymerization using MATrp and HEMA monomers. Magnetic hydrophobic microparticles were characterized via Fourier transform infrared spectroscopy, scanning electron microscopy, and vibrating sample magnetometer. Adsorption experiments were conducted for different conditions (pH, interaction time, amount of microparticles, temperature, and ionic strength) in batch system. VBR adsorption capacity of magnetic hydrophobic microparticles was estimated as 89.46 μmol/g. Adsorption–desorption cycles were repeated 4 times, and there was no significant decrease for the adsorption capacity observed.