NPNiki Prastomo

Niki Prastomo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Niki Prastomo has a total of 65 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Automatic Water Filling System of Flooded Lead-Acid Battery for Solar Home System

    by Niki Prastomo, Markus Aminius Gielbert, Nadya Laurencya

    The Solar Home System (SHS) implementation cannot be separated from the battery, which plays an essential role as an energy storage component. One type of battery that is economical and easy to apply as a battery for SHS is a flooded lead-acid battery. The main challenge in using these batteries is the need to carry out maintenance, namely manually filling the battery with water and keeping the water level in each cell balanced so that the battery’s performance is optimum. Therefore, in this project, a flooded lead-acid battery caps model was developed with a level sensor which can later be implemented as a component of an automatic water filling system. It has been made, designed, tested, and analyzed using a comparison of 3 models of caps with their respective level sensors, namely the caps model with float switch (FS) level sensor, optical liquid (OL) level sensor, and electric current (EC) level sensor. With a 100% effectiveness, 1.71 s delay time, 94.0% accuracy, and a precision rate of 98.1%, the cap model with FS level sensor is considered excellent to other caps models to be applied to the SHS scale automatic water filling system.

  • Focused ion beam and advanced electron microscopy for nano defect failure analysis of LED

    by R. Gunawan, E. Sugiarti, Isnaeni, R. I. Purawiardi, H. Widodo, A. N. Muslimin, Yuliasari, C. E. Ronaldus, N. Prastomo, S. Hastuty

    Focused Ion Beam (FIB) has attracted extensive use in fundamental materials studies and technological applications over the last several years because it allows manipulation of the shape and size of nanostructures of a material. Focused Ion Beam and Transmission Electron Microscopy are responsible as sample preparation and nano defect failure analysis tool, respectively. This research was conducted to observe the failure of commercial blue LED that has been injected with high current. The optical dan electrical properties and structure characterization was carry out to identify the degradation of LED. It was observed that high current injection caused defect generation which affects electron transport in quantum well layer. Observation with TEM showed the existence of early defect in LED prior high current injection. The defects appeared in the form of discontinue and edge defect that was found in dark spot region of LED.

  • Open Access

    Fabrication of gas diffusion layer from carbon ramie fiber by hot press method

    by D A Gumilar, N Indayaningsih, A Subhan, N Prastomo, S Hastuty

    Polymer exchange membrane fuel cell (PEMFC) is an electrical energy-generating device that is renewable and environmentally friendly. However, the price of components in PEMFC is still relatively expensive and more studies are needed on making cheaper components in terms of methods and raw materials. In this research, the fabrication of gas diffusion layer (GDL) which is a component of PEMFC made from ramie fiber was investigated. The processes of preparing GDL in this research were divided into two parts: the process of making carbon from ramie fiber through pyrolysis process and fabrication of composite from carbon ramie fiber and urea formaldehyde resin (UFR) by hot press method. The carbon results from the process of pyrolysis of degummed ramie fiber with variations in pyrolysis temperature of 500 °C, 900 °C, 1100 °C and 1300 °C yield electrical conductivity values of 8.7 × 10−7 S/cm, 0.84 S/cm, 3.72 S/cm and 4.6 S/cm, respectively. The electrical conductivity of carbon ramie fiber was increased by degumming and increasing pyrolysis temperature. The 1300 °C carbon composite with a hydrophobic coating 10 wt.% FEP has an electrical conductivity of 0.25 S/cm and a water droplet angle of 133° (hydrophobic). Composites of carbon ramie fiber have potential as GDL in PEMFC.


  • Open Access

    Effect of high current density to defect generation of blue LED and its characterization with transmission electron microscope

    by R Gunawan, E Sugiarti, Isnaeni, R I Purawiardi, H Widodo, A N Muslimin, Yuliasari, C E Ronaldus, N Prastomo, S Hastuty


  • Open Access

    Synthesis of alumina ceramic encapsulation for self-healing materials on thermal barrier coating

    by O P Golim, N Prastomo, H Izzudin, S Hastuty, R Sundawa, E Sugiarti, K A Z Thosin

    Durability of Thermal Barrier Coating or TBC can be optimized by inducing Self-Healing capabilities with intermetallic materials MoSi2. Nevertheless, high temperature operation causes the self-healing materials to become oxidized and lose its healing capabilities. Therefore, a method to introduce ceramic encapsulation for MoSi2 is needed to protect it from early oxidation. The encapsulation process is synthesized through a simple precipitation method with colloidal aluminum hydroxide as precursor and variations on calcination process. Semi-quantitative analysis on the synthesized sample is done by using X-ray diffraction (XRD) method. Meanwhile, qualitative analysis on the morphology of the encapsulation was carried out by using Scanning Electron Microscope (SEM) and Field Emission Scanning Electron Microscope (FESEM) equipped with dual Focus Ion Beam (FIB). The result of the experiment shows that calcination process significantly affects the final characteristic of encapsulation. The optimum encapsulation process was synthesized by colloidal aluminum hydroxide as a precursor, with a double step calcination process in low pressure until 900 °C.


  • Open Access

    Enhancing the efficiency of dye-sensitized solar cells by hydrothermal post-treatment in acidic environment

    by A Nathania, N M Nursam, Shobih, J Hidayat, N Prastomo

    Dye-sensitized solar cell (DSSC) have been extensively studied due to its low production cost and simple production process. In this research, DSSC with improved performance is acquired by modification of TiO2 layer through hydrothermal post-treatment with different hydrochloric acid (HCl) concentrations to obtain various particles and pore sizes. Qualitative and quantitative characterizations of the TiO2 film were conducted using thickness measurement, scanning electron microscope (SEM), and X-ray diffraction (XRD), while the solar cell performances were characterized using current-voltage (I-V) measurement under 0.5 Sun. When hydrothermally treated with 1 mol/L HCl at 180 °C for 3 h, the DSSC showed the most optimum photo-electricity conversion performance of 3.60%, which improved the efficiency of the non-treated DSSC by a factor of 1.2. As the HCl concentration increased, the treated TiO2 film became thinner with smaller particle size and denser structure. It was suspected that the modification in the TiO2 film morphology has led to better light absorption, which consequently resulted in the improvement of DSSC performance.

  • Role of tungsten, niobium, and vanadium on corrosion resistance of austenitic stainless steels in chloride ion environment

    by R. M. Andrianingtyas, M. S. Anwar, S. Hastuty, I. D. Widharyanti, A. Dahliyanti, N. Prastomo, E. Mabruri

    The effect of addition of refractory elements; Tungsten, Niobium and Vanadium, on the corrosion resistance of austenitic stainless steels in chloride environment were investigated. Corrosion resistance was evaluated under conditions of immersion, potentiodynamic polarization and cyclic polarization vs. SCE in corrosive medium of 1.5, 2.5, and 3.5%NaCl salts. An increment of temperatures was also used; room temperature, 50 and 90 °C. The results showed that Fe-25Ni-15Cr-2W-2Nb-1V alloys have the lowest tendency of pitting corrosion to occur compared to other alloys. The increase of temperatures of these alloys demonstrated an improvement of corrosion resistance, especially for Fe-25Ni-15Cr-2W-2Nb-1V.


  • Synthesis and Characterization of MgPSZ-PMMA Composite by Sol-Gel Modification and Direct Foaming Technique Using Egg Whites

    by Veni Takarini, Alfend Rudyawan, Andri Hardiansyah, Rifki Septawendar, Niki Prastomo, Zulia Hasratiningsih, Nina Djustiana, Bambang Sunendar Purwasasmita

    This study prepared Magnesium-Partially Stabilized Zirconia (Mg-PSZ) filler synthesis and direct foaming technique using egg whites, and impregnated by PMMA. The results were evaluated systematically by X-ray diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Electron Microscope (TEM). XRD results denote that the powder sample of MgPSZ was successfully formed with various crystal size of tetragonal and monoclinic phase. SEM and TEM observations revealed that nanoparticles MgPSZ were in spherical and long rounded shapes. Furthermore, SEM observation revealed that the direct foaming method were also successful in the formation of porous structures which favourable for impregnation process by PMMA. The use of egg whites as a polymer precursor in both methods demonstrates that porous specimens contained nanosized, predominantly tetragonal, Mg-PSZ powders were successfully synthesized. This shall yield an interesting prospect towards cheap, reliable, and biocompatible product to resemble the modulus elasticity of dentin.

  • Utilization of Sludge from Sidoarjo Mudflow for Zeolite Synthesis

    by Chris Salim, Niki Prastomo, Yan Shao, Hirofumi Hinode

    Sidoarjo mudflow occurred in 2006 has been causing major environmental problems in a wide area surrounding the region. The utilization of the sludge from this mudflow as useful materials is a potential solution to this problem. In this study, we proposed a hydrothermal treatment method to convert the silica-rich sludge into zeolites useful as adsorbent for inorganic pollutants such as heavy metals. Prior to the hydrothermal treatment, the sludge was contacted with NaOH solution in a teflon vessel. During the hydrothermal treatment, the mixture was subjected to increasing temperature for a certain period of time. After hydrothermal treatment, the solid phase was filtered, washed thoroughly until neutral pH and dried. In this study, we evaluated the effect of NaOH concentration and hydrothermal treatment temperature on the type of zeolite formed. The surface morphology and composition of prepared zeolite was characterized by SEM-EDS while the type of zeolite was determined by XRD analysis. Preliminary study of the adsorption ability of the zeolites towards metal ions was carried out by CEC measurement using sodium acetate method.