Ahmed Zurfi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmed Zurfi has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Jing Zhang
University of Arkansas at Little Rock
12 shared publications- Hussain Sayed
Department of Electrical and Computer Engineering, University of Houston, Houston, TX, USA
4 shared publications - Ali Abdul Razzaq Altahir
University of Kerbala
1 shared publication - Ali Ibrahim Khaleel
Florida Atlantic University
1 shared publication Dallas Tompkins
Department of Systems Engineering, University of Arkansas at Little Rock, Little Rock, AR 72204
1 shared publicationGhaidaa Albayati
Department of Information Science, University of Arkansas at Little Rock, Little Rock, AR 72204, USA
1 shared publication
Latest Publications
- Open Access
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (3) , 1914-1925
Investigation of optimal tilt, orientation, and tracking of a solar PV system in Iraq
This paper examines the effect of tilt angle and tracking modes on energy performance of a PV system under Iraqi weather conditions. A 5-kWdc rooftop residential PV system is modeled and simulated using system advisor model (SAM) to investigate its optimal configuration of tilt angle and tracking axes for maximum energy extraction. The system is simulated with meteorological datasets for all 18 Iraqi provinces. The effect of soiling losses due to dust accumulation on incident irradiance and energy generation is considered as most Iraqi territories suffer from frequent dust storms yearly. The system annual AC energy and optimal tilt angles are evaluated and compared in five different scenarios including fixed-axis with tilt at latitude, fixed-axis with tilt at annual optimal angle, fixed-axis with tilt at monthly annual angle, one-axis tracking and dual-axis tracking. The results showed that considerable amount of energy is left unharnessed in fixed-axis scenarios when tilt angles are adjusted at latitude and optimal annual values. Using optimal monthly tilt with fixed-axis improved energy extraction by 5-6% for all locations. Energy performance is further improved with one axis tracking. Dual-axis tracking achieved highest energy yield compared to other scenarios. Overall, mid-south provinces provided highest energy opportunities among others.
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (3) , 1914-1925
Open AccessInvestigation of optimal tilt, orientation, and tracking of a solar PV system in Iraq
This paper examines the effect of tilt angle and tracking modes on energy performance of a PV system under Iraqi weather conditions. A 5-kWdc rooftop residential PV system is modeled and simulated using system advisor model (SAM) to investigate its optimal configuration of tilt angle and tracking axes for maximum energy extraction. The system is simulated with meteorological datasets for all 18 Iraqi provinces. The effect of soiling losses due to dust accumulation on incident irradiance and energy generation is considered as most Iraqi territories suffer from frequent dust storms yearly. The system annual AC energy and optimal tilt angles are evaluated and compared in five different scenarios including fixed-axis with tilt at latitude, fixed-axis with tilt at annual optimal angle, fixed-axis with tilt at monthly annual angle, one-axis tracking and dual-axis tracking. The results showed that considerable amount of energy is left unharnessed in fixed-axis scenarios when tilt angles are adjusted at latitude and optimal annual values. Using optimal monthly tilt with fixed-axis improved energy extraction by 5-6% for all locations. Energy performance is further improved with one axis tracking. Dual-axis tracking achieved highest energy yield compared to other scenarios. Overall, mid-south provinces provided highest energy opportunities among others.
- 1 April 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 99 (1) , 81-93
Effects of PCB power layouts design on switching transient performance of SiC MOSFETs
- 1 April 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 99 (1) , 81-93
Effects of PCB power layouts design on switching transient performance of SiC MOSFETs
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 842-849
Economic feasibility of residential behind-the-meter battery energy storage under energy time-of-use and demand charge rates
In this paper, the economic viability of using behind-the-meter battery energy storage (BMBES) for time-of-use (ToU) energy arbitrage and demand charge (DC) reduction is compared. The study focuses on residential applications where the BMBES is installed at end-users premises and used for daily cycling under ToU and DC plans for saving on monthly electricity bills. Under the current U.S. electricity prices, different case studies of using two BMBES systems are discussed. The two systems are analyzed with practical load profiles of a two-story American family house. A number of ToU and DC plans from different utility companies and with different pricing structures are applied. First, the mathematical formulation of the monthly savings in the electricity bill is presented to determine the different technical and economic factors that affect the savings. Then, the System Advisor Model (SAM) software tool, which provides a techno-economic model of battery storage systems, is used for hourly, monthly, and annual analysis. In each scenario, the economic performance of the BMBES systems in terms of the cash flow diagram, net present worth and payback period is presented and discussed. Based on the analysis results, a set of implications on the profitability of the ToU energy arbitrage and DC reduction schemes under current prices of energy storage and electricity rates are stated. Such implications can be beneficial to customers and practitioners for selecting and designing residential electric rates.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 842-849
Economic feasibility of residential behind-the-meter battery energy storage under energy time-of-use and demand charge rates
In this paper, the economic viability of using behind-the-meter battery energy storage (BMBES) for time-of-use (ToU) energy arbitrage and demand charge (DC) reduction is compared. The study focuses on residential applications where the BMBES is installed at end-users premises and used for daily cycling under ToU and DC plans for saving on monthly electricity bills. Under the current U.S. electricity prices, different case studies of using two BMBES systems are discussed. The two systems are analyzed with practical load profiles of a two-story American family house. A number of ToU and DC plans from different utility companies and with different pricing structures are applied. First, the mathematical formulation of the monthly savings in the electricity bill is presented to determine the different technical and economic factors that affect the savings. Then, the System Advisor Model (SAM) software tool, which provides a techno-economic model of battery storage systems, is used for hourly, monthly, and annual analysis. In each scenario, the economic performance of the BMBES systems in terms of the cash flow diagram, net present worth and payback period is presented and discussed. Based on the analysis results, a set of implications on the profitability of the ToU energy arbitrage and DC reduction schemes under current prices of energy storage and electricity rates are stated. Such implications can be beneficial to customers and practitioners for selecting and designing residential electric rates.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
An electrical model for energy efficiency evaluation of NiMH batteries
In this work, we propose an electrical model of the battery based on its equivalent circuit for the evaluation of the energy efficiency. The circuit model consists of a current-dependent nonlinear resistance to model the total drop in the battery voltage caused by the activation, concentration, and Ohmic polarizations. The effects of the coulomb losses on the battery run time are also considered in the model. The model targets the state of charge range from 20% to 80% in which best energy efficiency can be achieved, and the total resistance is a function of the battery current magnitude only. The model is intended to be used for real-time management of the battery energy efficiency in grid-connected applications. Through experiments and simulations of two NiMH battery packs, we confirm the effectiveness of the model in evaluating the energy efficiency at different conditions of charge and discharge currents.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
An electrical model for energy efficiency evaluation of NiMH batteries
In this work, we propose an electrical model of the battery based on its equivalent circuit for the evaluation of the energy efficiency. The circuit model consists of a current-dependent nonlinear resistance to model the total drop in the battery voltage caused by the activation, concentration, and Ohmic polarizations. The effects of the coulomb losses on the battery run time are also considered in the model. The model targets the state of charge range from 20% to 80% in which best energy efficiency can be achieved, and the total resistance is a function of the battery current magnitude only. The model is intended to be used for real-time management of the battery energy efficiency in grid-connected applications. Through experiments and simulations of two NiMH battery packs, we confirm the effectiveness of the model in evaluating the energy efficiency at different conditions of charge and discharge currents.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 125-129
Investigation of the effects of load parasitic inductance on SiC MOSFETs switching performance
Parasitic inductances are responsible for oscillations and overshoots in the switching waveforms of SiC MOSFETs under high-frequency operations. In addition to the parasitic inductance of PCB board, bus-bar, device packaging, and drive circuit, the load inductance used for energy storage represents another source of parasitic inductance in SiC MOSFETs converters. Therefore, it is necessary to study the effect of the parasitic inductance contributed by inductive loads. This paper studies the effects of the load parasitic inductance on the switching performance of a SiC MOSFET-based switching power pole (SPP) or what traditionally defined as a half-bridge. The goal is to identify the influence of the load parasitic inductance on the overshoot and ringing in the waveforms of the device drain-to-source voltage and drain current. Using a simple procedure based on experimental measurements of the device drain-to-source voltage and drain current along with the mathematical formula of the inductance, the value of the parasitic inductance of the load inductor was evaluated.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 125-129
Investigation of the effects of load parasitic inductance on SiC MOSFETs switching performance
Parasitic inductances are responsible for oscillations and overshoots in the switching waveforms of SiC MOSFETs under high-frequency operations. In addition to the parasitic inductance of PCB board, bus-bar, device packaging, and drive circuit, the load inductance used for energy storage represents another source of parasitic inductance in SiC MOSFETs converters. Therefore, it is necessary to study the effect of the parasitic inductance contributed by inductive loads. This paper studies the effects of the load parasitic inductance on the switching performance of a SiC MOSFET-based switching power pole (SPP) or what traditionally defined as a half-bridge. The goal is to identify the influence of the load parasitic inductance on the overshoot and ringing in the waveforms of the device drain-to-source voltage and drain current. Using a simple procedure based on experimental measurements of the device drain-to-source voltage and drain current along with the mathematical formula of the inductance, the value of the parasitic inductance of the load inductor was evaluated.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Effects of SiC schottky barrier diodes on switching transient performance of a SIC MOSFETs-based bidirectional switching power pole
This paper presents the investigation of the effects of Silicon-Carbide Schottky Barrier Diodes (SiC SBDs) on the switching transient performance of a SiC MOSFETs-based Bidirectional Switching Power Pole (BSPP). The investigation was focused on the contribution of the SiC SBDs in reducing the overshoot in the drain current when they are connected as freewheeling diodes. A double pulse test (DPT) is used to measure the switching transients of the MOSFETs at room temperature. To verify the practical analysis, a simulation circuit of the SiC BSPP is designed by using Cadence simulation tools. The experimental and simulation results showed that using SiC SBDs as freewheeling diodes have negligible improvements in the switching transients of the SiC MOSFET.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Effects of SiC schottky barrier diodes on switching transient performance of a SIC MOSFETs-based bidirectional switching power pole
This paper presents the investigation of the effects of Silicon-Carbide Schottky Barrier Diodes (SiC SBDs) on the switching transient performance of a SiC MOSFETs-based Bidirectional Switching Power Pole (BSPP). The investigation was focused on the contribution of the SiC SBDs in reducing the overshoot in the drain current when they are connected as freewheeling diodes. A double pulse test (DPT) is used to measure the switching transients of the MOSFETs at room temperature. To verify the practical analysis, a simulation circuit of the SiC BSPP is designed by using Cadence simulation tools. The experimental and simulation results showed that using SiC SBDs as freewheeling diodes have negligible improvements in the switching transients of the SiC MOSFET.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Experimental evaluation of the energy efficiency of a grid-connected NiMH battery system
Energy efficiency is considered a critical technical parameter for the performance evaluation, sizing, and design of control strategies of grid-connected battery systems. Therefore, measurement of the energy efficiency of grid-connected battery systems is necessary. In this paper, the experimental evaluation and measurement of the energy efficiency of a small-scale grid-connected NiMH battery system are presented. The studied system consists of 3 Ah NiMH battery packs interfaced to the grid via a conventional power conditioning converter. First, the energy efficiency of two battery packs with different voltage ratings was evaluated at various battery current rates. Next, the energy efficiency of the power conditioning converter was measured for charging and discharging scenarios at the different current settings. Finally, the effect of the charge recovery phenomenon on the battery energy performance was investigated under the charge and discharge conditions of the primary frequency control application.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Experimental evaluation of the energy efficiency of a grid-connected NiMH battery system
Energy efficiency is considered a critical technical parameter for the performance evaluation, sizing, and design of control strategies of grid-connected battery systems. Therefore, measurement of the energy efficiency of grid-connected battery systems is necessary. In this paper, the experimental evaluation and measurement of the energy efficiency of a small-scale grid-connected NiMH battery system are presented. The studied system consists of 3 Ah NiMH battery packs interfaced to the grid via a conventional power conditioning converter. First, the energy efficiency of two battery packs with different voltage ratings was evaluated at various battery current rates. Next, the energy efficiency of the power conditioning converter was measured for charging and discharging scenarios at the different current settings. Finally, the effect of the charge recovery phenomenon on the battery energy performance was investigated under the charge and discharge conditions of the primary frequency control application.
- 17 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 460-464
Design and experiments of a SiC power MOSFET bidirectional switching power pole
This paper presents the design and experiments of a SiC power MOSFET-based bidirectional switching power pole (BSPP) by benefiting from the advantages of SiC power MOSFETs: high-speed switching, high power density, and low power losses. The goal of the work is to design a printed circuit board (PCB) power traces of the BSPP with the minimum parasitic inductance and balanced switching transient performance between the high-side and low-side power MOSFETs. With such power traces, it is possible to reach the best switching performance with SiC power MOSFETs. A prototype BSPP with SiC power MOSFETs was developed and tested. A simulation of the prototype circuit model was built using Cadence simulation tools. The simulation and experimental results were compared to validate the model parameters and the calculated parasitic inductance of the PCB power traces.
- 17 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 460-464
Design and experiments of a SiC power MOSFET bidirectional switching power pole
This paper presents the design and experiments of a SiC power MOSFET-based bidirectional switching power pole (BSPP) by benefiting from the advantages of SiC power MOSFETs: high-speed switching, high power density, and low power losses. The goal of the work is to design a printed circuit board (PCB) power traces of the BSPP with the minimum parasitic inductance and balanced switching transient performance between the high-side and low-side power MOSFETs. With such power traces, it is possible to reach the best switching performance with SiC power MOSFETs. A prototype BSPP with SiC power MOSFETs was developed and tested. A simulation of the prototype circuit model was built using Cadence simulation tools. The simulation and experimental results were compared to validate the model parameters and the calculated parasitic inductance of the PCB power traces.
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A grid-interfaced test system for modeling of NiMH batteries in a battery-buffered smart load application
Testing and modeling of batteries are essential to evaluate the performance and effectiveness of battery energy storage systems (BESS) in power system applications. The procedure of extraction and experimental verification of any battery model require a reliable and efficient testing system. In this paper, a programmable grid-interfaced battery test system for battery modeling in a frequency-controlled battery-buffered smart load application is proposed. The testbed is based on the same smart load experimental system which consists of a single phase bidirectional AC-DC converter, a DC-link, and a bidirectional DC-DC converter. The AC-DC converter is designed to control a bidirectional power flow between the AC-line and the DC-link. Therefore, the energy can be controlled effectively flowing between the battery and the power line during charge and discharge without significant power losses. This design realizes an energy-conserving electronic load by supplying the battery energy to the grid instead of dissipating it during discharge. To verify the functionality of the developed test system, 3Ah, 1.2V NiMH batteries were tested for a Thevenin-based model identification. Then, a simulation of the identified model was implemented in MATLAB/Simulink to validate the model under the smart load charging and discharging conditions.
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A grid-interfaced test system for modeling of NiMH batteries in a battery-buffered smart load application
Testing and modeling of batteries are essential to evaluate the performance and effectiveness of battery energy storage systems (BESS) in power system applications. The procedure of extraction and experimental verification of any battery model require a reliable and efficient testing system. In this paper, a programmable grid-interfaced battery test system for battery modeling in a frequency-controlled battery-buffered smart load application is proposed. The testbed is based on the same smart load experimental system which consists of a single phase bidirectional AC-DC converter, a DC-link, and a bidirectional DC-DC converter. The AC-DC converter is designed to control a bidirectional power flow between the AC-line and the DC-link. Therefore, the energy can be controlled effectively flowing between the battery and the power line during charge and discharge without significant power losses. This design realizes an energy-conserving electronic load by supplying the battery energy to the grid instead of dissipating it during discharge. To verify the functionality of the developed test system, 3Ah, 1.2V NiMH batteries were tested for a Thevenin-based model identification. Then, a simulation of the identified model was implemented in MATLAB/Simulink to validate the model under the smart load charging and discharging conditions.
- 1 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Experimental identification and validation of a battery model for a battery-buffered frequency-controlled smart load
This paper presents an experimental extraction and validation of a battery model for a battery-buffered frequency-responsive smart load application. The considered model is based on a Thevenin equivalent circuit. It is capable of modeling the batteries transient behavior during charge and discharge. In order to extract the model parameters at different conditions of current and state of charge, an automatic test system was developed to implement different charge and discharge test profiles. In the experiments, new 3 Ah, 1.2 V NiMH (HHR300SCP) battery cells from Panasonic were tested individually and in series-connected packs. First, the model was experimentally identified and compared for a single cell and multiple series-connected cells. The model parameters of each configuration were extracted from the experimental measurements of the batteries voltage and current response to pulsed charge and discharge tests. Next, the identified model of a selected single cell was used to simulate the series-connected cells. Then, a simulation of the model was built in Matlab/Simulink to validate the model and study its accuracy in modeling multiple cells in series configurations. Finally, the model was validated for a six-cell series-connected pack under the charging and discharging profiles of the frequency-controlled smart load.
- 1 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Experimental identification and validation of a battery model for a battery-buffered frequency-controlled smart load
This paper presents an experimental extraction and validation of a battery model for a battery-buffered frequency-responsive smart load application. The considered model is based on a Thevenin equivalent circuit. It is capable of modeling the batteries transient behavior during charge and discharge. In order to extract the model parameters at different conditions of current and state of charge, an automatic test system was developed to implement different charge and discharge test profiles. In the experiments, new 3 Ah, 1.2 V NiMH (HHR300SCP) battery cells from Panasonic were tested individually and in series-connected packs. First, the model was experimentally identified and compared for a single cell and multiple series-connected cells. The model parameters of each configuration were extracted from the experimental measurements of the batteries voltage and current response to pulsed charge and discharge tests. Next, the identified model of a selected single cell was used to simulate the series-connected cells. Then, a simulation of the model was built in Matlab/Simulink to validate the model and study its accuracy in modeling multiple cells in series configurations. Finally, the model was validated for a six-cell series-connected pack under the charging and discharging profiles of the frequency-controlled smart load.