Jurij Karlovšek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jurij Karlovšek has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Norman Wagner
Institute of Material Research and Testing, Bauhaus-University Weimar, Weimar, Germany
6 shared publications - Songtao Ji
College of Energy and Mining Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
6 shared publications - Jie Zhang
College of Safety Science and Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
3 shared publications - Keith W. K. Kong
Tactix Sener Group Australia Pty, Melbourne, VIC 3000, Australia
3 shared publications - Mojtaba Rajabi
School of the Environment, The University of Queensland, Saint Lucia, Queensland, Australia
3 shared publications - Moritz Schwing
Geotechnical Engineering Centre, School of Civil Engineering, The University of Queensland, Advanced Engineering Building 49, 4072 Queensland, Australia
3 shared publications
Latest Publications
- Open Access
- 6 October 2026
- Published by Elsevier in International Journal of Rock Mechanics and Mining Sciences
- Vol. 208
Maximum achievable span of rock-reinforced caverns in jointed rock masses – A parametric study
- 6 October 2026
- Published by Elsevier in International Journal of Rock Mechanics and Mining Sciences
- Vol. 208
Open AccessMaximum achievable span of rock-reinforced caverns in jointed rock masses – A parametric study
- Open Access
- 1 September 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (17) , 3138
Analytical Inversion of the Equivalent Horizontal Load on Shield Tunnel Linings from a Single-Point Rotation Measurement
External loads acting on shield tunnel linings in service are difficult to determine, while existing back analysis methods often require multiple monitoring quantities and repeated numerical calculations. This study develops an analytical method for identifying the equivalent horizontal load and lateral pressure coefficient from a single rotation measurement. The lining is modelled as a continuous Euler–Bernoulli curved beam on a radial Winkler foundation, with circumferential compression and bending considered. The radial components of the vertical and horizontal loads are decomposed into uniform and second-order terms. Closed-form solutions are obtained for displacement, rotation, and internal forces, followed by an explicit inverse relation between rotation at one circumferential position and the load difference. The analytical responses agree closely with an independent plane-frame finite element model. Prescribed horizontal loads and lateral pressure coefficients are also recovered accurately from finite element rotations. A FLAC3D model of the complete ring with continuous elastic ground further shows that the circumferential response pattern is retained and that the equivalent horizontal load can still be estimated when the Winkler ground representation is relaxed. The method identifies the load difference from one rotation measurement, and when the vertical load is independently estimated, determines the equivalent horizontal load. It provides a basis for assessing lining ovalization, bending response, and abnormal loading states.
- 1 September 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (17) , 3138
Open AccessAnalytical Inversion of the Equivalent Horizontal Load on Shield Tunnel Linings from a Single-Point Rotation Measurement
External loads acting on shield tunnel linings in service are difficult to determine, while existing back analysis methods often require multiple monitoring quantities and repeated numerical calculations. This study develops an analytical method for identifying the equivalent horizontal load and lateral pressure coefficient from a single rotation measurement. The lining is modelled as a continuous Euler–Bernoulli curved beam on a radial Winkler foundation, with circumferential compression and bending considered. The radial components of the vertical and horizontal loads are decomposed into uniform and second-order terms. Closed-form solutions are obtained for displacement, rotation, and internal forces, followed by an explicit inverse relation between rotation at one circumferential position and the load difference. The analytical responses agree closely with an independent plane-frame finite element model. Prescribed horizontal loads and lateral pressure coefficients are also recovered accurately from finite element rotations. A FLAC3D model of the complete ring with continuous elastic ground further shows that the circumferential response pattern is retained and that the equivalent horizontal load can still be estimated when the Winkler ground representation is relaxed. The method identifies the load difference from one rotation measurement, and when the vertical load is independently estimated, determines the equivalent horizontal load. It provides a basis for assessing lining ovalization, bending response, and abnormal loading states.
- Open Access
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Geometry-Dependent Support Demand in Rock-Reinforced Excavations: Extending the Q-System Through Deformation-Controlled Arch Mechanics
Current empirical rock support design methods, including the Q-system, do not explicitly consider excavation geometry, even though arch-shaped openings are commonly used in underground construction. This study quantifies how roof arch geometry affects the rock support requirements for reinforced rock openings, focusing on rise-to-span ratios between 0.1 and 0.4. Building on a previously developed deformation-based, semi-empirical framework for predicting opening span, the research systematically investigates the relationship between arch geometry and Q-system support pressure, using a mechanics-based interpretation of rock-reinforced arch behaviour. The results show that arches with higher-rise consistently achieve larger stable spans under the same rock mass and in-situ stress conditions, enabling meaningful reductions in required support pressure. For arch rise-to-span ratios of 0.3 and 0.4, support pressure reductions of approximately 5–11% are achieved in poor rock masses (35 ≤ GSI ≤ 45), increasing to 6–19% in fair-quality rock masses (GSI ≈ 55). Validation with independent numerical models confirms that deformation remains within acceptable limits. A constructability assessment also highlights the implications for rockbolt demand and excavation volume. This study introduces a Support Load Improvement Factor, which allows rational adjustment of Q-system support pressures, enabling more efficient and geometry-optimised designs that balance structural efficiency, sustainability, and economic viability in underground development projects. More importantly, the results demonstrate that excavation geometry acts as an independent design variable within deformation-controlled rock-reinforced systems, establishing a mechanics-based link between span capacity and support demand that is not explicitly captured by existing empirical support design methods.
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessGeometry-Dependent Support Demand in Rock-Reinforced Excavations: Extending the Q-System Through Deformation-Controlled Arch Mechanics
Current empirical rock support design methods, including the Q-system, do not explicitly consider excavation geometry, even though arch-shaped openings are commonly used in underground construction. This study quantifies how roof arch geometry affects the rock support requirements for reinforced rock openings, focusing on rise-to-span ratios between 0.1 and 0.4. Building on a previously developed deformation-based, semi-empirical framework for predicting opening span, the research systematically investigates the relationship between arch geometry and Q-system support pressure, using a mechanics-based interpretation of rock-reinforced arch behaviour. The results show that arches with higher-rise consistently achieve larger stable spans under the same rock mass and in-situ stress conditions, enabling meaningful reductions in required support pressure. For arch rise-to-span ratios of 0.3 and 0.4, support pressure reductions of approximately 5–11% are achieved in poor rock masses (35 ≤ GSI ≤ 45), increasing to 6–19% in fair-quality rock masses (GSI ≈ 55). Validation with independent numerical models confirms that deformation remains within acceptable limits. A constructability assessment also highlights the implications for rockbolt demand and excavation volume. This study introduces a Support Load Improvement Factor, which allows rational adjustment of Q-system support pressures, enabling more efficient and geometry-optimised designs that balance structural efficiency, sustainability, and economic viability in underground development projects. More importantly, the results demonstrate that excavation geometry acts as an independent design variable within deformation-controlled rock-reinforced systems, establishing a mechanics-based link between span capacity and support demand that is not explicitly captured by existing empirical support design methods.
- Open Access
- 30 June 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (13) , 2313
Support Roof Interaction Under Lower Hard Roof Conditions in Longwall Mining
Hard roofs in longwall mining may form large, suspended strata, which induce strong abutment stress redistribution. Therefore, a rational face support design is essential for ground control. This study develops an analytical numerical framework to evaluate support roof interaction under hard roof conditions. A segmented beam foundation model is established for the support roof system, and an equivalent variable foundation modulus is introduced to represent the reduced bearing capacity of yielded coal ahead of the working face. The analytical results are checked against a Particle Flow Code (PFC) and Fast Lagrangian Analysis of Continua (FLAC) coupled model, showing good agreement in the magnitude and location of the peak abutment stress. Parametric analyses are then conducted to examine the effects of support intensity and support distance on roof deflection, rotation, bending moment, shear force, strain energy density, and abutment stress. The results show that increasing support capacity reduces roof deformation and coal wall stress, while redistributing the same capacity over a longer support distance more effectively lowers roof strain energy concentration and inclined fracture development. However, the longer distance, lower density arrangement may transfer stress deeper into the coal seam and increase peak stress fluctuation during face advance. The proposed study provides a practical method for comparing face support schemes under low position hard roof conditions.
- 30 June 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (13) , 2313
Open AccessSupport Roof Interaction Under Lower Hard Roof Conditions in Longwall Mining
Hard roofs in longwall mining may form large, suspended strata, which induce strong abutment stress redistribution. Therefore, a rational face support design is essential for ground control. This study develops an analytical numerical framework to evaluate support roof interaction under hard roof conditions. A segmented beam foundation model is established for the support roof system, and an equivalent variable foundation modulus is introduced to represent the reduced bearing capacity of yielded coal ahead of the working face. The analytical results are checked against a Particle Flow Code (PFC) and Fast Lagrangian Analysis of Continua (FLAC) coupled model, showing good agreement in the magnitude and location of the peak abutment stress. Parametric analyses are then conducted to examine the effects of support intensity and support distance on roof deflection, rotation, bending moment, shear force, strain energy density, and abutment stress. The results show that increasing support capacity reduces roof deformation and coal wall stress, while redistributing the same capacity over a longer support distance more effectively lowers roof strain energy concentration and inclined fracture development. However, the longer distance, lower density arrangement may transfer stress deeper into the coal seam and increase peak stress fluctuation during face advance. The proposed study provides a practical method for comparing face support schemes under low position hard roof conditions.
- Open Access
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Maximum Achievable Span of Rock-Reinforced Caverns in Jointed Rock Masses – A Parametric Study
The maximum stable span of underground caverns is a key constraint governing feasibility, constructability, and cost, yet span limits for rock‐reinforced caverns remain poorly defined. In particular, the combined influences of roof arch geometry, rock mass deformability, and in‐situ stress conditions are rarely addressed in existing design frameworks. This study addresses these gaps through a systematic parametric investigation of rock-reinforced caverns constructed in blocky rock masses. A total of 180 two‐dimensional finite element models incorporating discrete fracture networks were developed to evaluate cavern stability across a controlled range of rock mass qualities (GSI 35–55), intact rock strengths, roof arch rise‐to‐span ratios, excavation depths, and in-situ stress ratios. Stability was assessed using deformation‐based criteria (Roof Sag Ratio and Wall Convergence Ratio), and selected cases were benchmarked against discrete element models to cross-check the numerical approach. The results demonstrate that rock mass deformation modulus is the dominant control on span capacity, while roof arch geometry is shown to be a critical and previously under‐quantified design variable, with higher rise‐to‐span ratios consistently enabling larger stable openings. Based on these findings, a new mechanics‐informed empirical equation is proposed to estimate the potential maximum achievable span solely for rock‐reinforced caverns, providing a practical tool for preliminary design and underground space planning.
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMaximum Achievable Span of Rock-Reinforced Caverns in Jointed Rock Masses – A Parametric Study
The maximum stable span of underground caverns is a key constraint governing feasibility, constructability, and cost, yet span limits for rock‐reinforced caverns remain poorly defined. In particular, the combined influences of roof arch geometry, rock mass deformability, and in‐situ stress conditions are rarely addressed in existing design frameworks. This study addresses these gaps through a systematic parametric investigation of rock-reinforced caverns constructed in blocky rock masses. A total of 180 two‐dimensional finite element models incorporating discrete fracture networks were developed to evaluate cavern stability across a controlled range of rock mass qualities (GSI 35–55), intact rock strengths, roof arch rise‐to‐span ratios, excavation depths, and in-situ stress ratios. Stability was assessed using deformation‐based criteria (Roof Sag Ratio and Wall Convergence Ratio), and selected cases were benchmarked against discrete element models to cross-check the numerical approach. The results demonstrate that rock mass deformation modulus is the dominant control on span capacity, while roof arch geometry is shown to be a critical and previously under‐quantified design variable, with higher rise‐to‐span ratios consistently enabling larger stable openings. Based on these findings, a new mechanics‐informed empirical equation is proposed to estimate the potential maximum achievable span solely for rock‐reinforced caverns, providing a practical tool for preliminary design and underground space planning.
- Open Access
- 8 August 2025
- Published by MDPI AG in Mathematics
- Vol. 13 (16) , 2548
The Control Mechanism of the Coal Pillar Width on the Mechanical State of Hard Roofs
This study addresses the critical challenge of optimizing coal pillar width in burst-prone mines with thick, hard roof strata, balancing resource recovery, roadway stability, and coal burst mitigation. Through integrated analytical modeling and rigorously calibrated numerical simulations, the research reveals the complex interplay between pillar width, roof mechanics, and stress redistribution. Key findings demonstrate that pillar width dictates roof failure mechanics and energy accumulation. The case study indicates that increasing the coal pillar width from 6 m to 20 m shifts the tensile fracture location from solid coal toward the pillar center, migrates shear failure zones closer to roadways, and relocates elastic strain energy accumulation to the pillar area. This concentrates static and dynamic loads directly onto wider pillars upon roof fracture, escalating instability risks. A risky coal pillar width is identified as 10–20 m, where pillars develop severe lateral abutment pressures perilously close to roadways, combining high elastic energy storage with exposure to roof fracture dynamics. Conversely, narrow pillars exhibit low stress concentrations and limited energy storage due to plastic deformation, reducing burst potential despite requiring robust asymmetric support. Strategic selection of narrow or wide pillars provides a safer pathway. The validated analytical–numerical framework offers a scientifically grounded methodology for pillar design under hard roof conditions, enhancing resource recovery while mitigating coal burst risks.
- 8 August 2025
- Published by MDPI AG in Mathematics
- Vol. 13 (16) , 2548
Open AccessThe Control Mechanism of the Coal Pillar Width on the Mechanical State of Hard Roofs
This study addresses the critical challenge of optimizing coal pillar width in burst-prone mines with thick, hard roof strata, balancing resource recovery, roadway stability, and coal burst mitigation. Through integrated analytical modeling and rigorously calibrated numerical simulations, the research reveals the complex interplay between pillar width, roof mechanics, and stress redistribution. Key findings demonstrate that pillar width dictates roof failure mechanics and energy accumulation. The case study indicates that increasing the coal pillar width from 6 m to 20 m shifts the tensile fracture location from solid coal toward the pillar center, migrates shear failure zones closer to roadways, and relocates elastic strain energy accumulation to the pillar area. This concentrates static and dynamic loads directly onto wider pillars upon roof fracture, escalating instability risks. A risky coal pillar width is identified as 10–20 m, where pillars develop severe lateral abutment pressures perilously close to roadways, combining high elastic energy storage with exposure to roof fracture dynamics. Conversely, narrow pillars exhibit low stress concentrations and limited energy storage due to plastic deformation, reducing burst potential despite requiring robust asymmetric support. Strategic selection of narrow or wide pillars provides a safer pathway. The validated analytical–numerical framework offers a scientifically grounded methodology for pillar design under hard roof conditions, enhancing resource recovery while mitigating coal burst risks.
- Open Access
- 26 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10983
Natural Creation of Large Rock Cavern: Can We Construct Them? Jenolan Caves as a Case Study
The Jenolan Caves are the most spectacular limestone caves in Australia. Within this cave system, the Grand Arch, which is 24 m high, 55 m wide, and 127 m long, is the largest open cave in the country. A cave of this size could potentially accommodate small city streets, buildings, and other facilities. This paper examines a stability simulation of the Grand Arch, using numerical models to deduce foundational insights into rock openings under different geological and rock mass conditions. Following this, using numerical analysis, we investigate the creation of a man-made rock opening with the same span, height, and ground conditions of the Grand Arch but formed in two different arch shapes (i.e., with and without rock reinforcement as a stabilization measure). With all stability simulations conducted in this study, a clear explanation to describe the relationship and interaction between various parameters, such as rock mass structure and quality, rock mass strength, and in situ stress field, as well as different arch roofs shapes of the rock opening, is provided. Through its comparisons between natural rock cave and man-made rock openings, this study provides some findings and deep insight, as well as further questioning on creating a large size rock-reinforced cavern in different shapes to be opened in a range of rock conditions.
- 26 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10983
Open AccessNatural Creation of Large Rock Cavern: Can We Construct Them? Jenolan Caves as a Case Study
The Jenolan Caves are the most spectacular limestone caves in Australia. Within this cave system, the Grand Arch, which is 24 m high, 55 m wide, and 127 m long, is the largest open cave in the country. A cave of this size could potentially accommodate small city streets, buildings, and other facilities. This paper examines a stability simulation of the Grand Arch, using numerical models to deduce foundational insights into rock openings under different geological and rock mass conditions. Following this, using numerical analysis, we investigate the creation of a man-made rock opening with the same span, height, and ground conditions of the Grand Arch but formed in two different arch shapes (i.e., with and without rock reinforcement as a stabilization measure). With all stability simulations conducted in this study, a clear explanation to describe the relationship and interaction between various parameters, such as rock mass structure and quality, rock mass strength, and in situ stress field, as well as different arch roofs shapes of the rock opening, is provided. Through its comparisons between natural rock cave and man-made rock openings, this study provides some findings and deep insight, as well as further questioning on creating a large size rock-reinforced cavern in different shapes to be opened in a range of rock conditions.
- 22 March 2024
- Published by Taylor & Francis in Australian Journal of Multi-Disciplinary Engineering
- Vol. 20 (1) , 88-106
Recommended rock joints setting in 2D FEM simulations for engineering design of excavations created in jointed rockmass
- 22 March 2024
- Published by Taylor & Francis in Australian Journal of Multi-Disciplinary Engineering
- Vol. 20 (1) , 88-106
Recommended rock joints setting in 2D FEM simulations for engineering design of excavations created in jointed rockmass
- Open Access
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Large Ring Test for Evaluation of Restrained Shrinkage Cracking: Calibration and Experimental Trial
The durability of shotcrete tunnel linings is significantly affected by restrained shrinkage cracking. Given the unique characteristics of shotcrete applied in tunnel linings, especially when dealing with accelerated shotcrete containing reinforcement fibres, it is necessary to upscale the ring test commonly used. This paper presents a comprehensive experiment using large ring tests with cast concrete to investigate the impact of upscaling ring test geometry. The two ring specimens demonstrated comparable cracking age (22 days) and strain measured in the steel ring, suggesting that consistent results can be obtained through the proposed instrumentation, calibration, and correction methods. Moreover, the estimated induced tensile stresses of the concrete rings (2.8 and 2.7 MPa) are slightly lower than the predicted tensile strength (3.3 MPa) at the age of cracking, which indicates that some driving forces contributing to restrained shrinkage cracking were not indicated in the strain gauge readings. Furthermore, the study identified multi‐crack formation and additional potential causes for crack initiation, which include self‐restraint due to the moisture gradient in the vertical direction, deflection of the concrete ring caused by its self‐weight, and friction on the contact surface of the support. Therefore, optimising the geometry of the ring specimens and the apparatus is imperative to minimise additional driving forces and unmeasurable restraints for crack initiation, especially when employing the stress rate method to assess cracking potential.
- 1 January 2024
- Published by Wiley in Advances in Civil Engineering
- Vol. 2024 (1)
Open AccessLarge Ring Test for Evaluation of Restrained Shrinkage Cracking: Calibration and Experimental Trial
The durability of shotcrete tunnel linings is significantly affected by restrained shrinkage cracking. Given the unique characteristics of shotcrete applied in tunnel linings, especially when dealing with accelerated shotcrete containing reinforcement fibres, it is necessary to upscale the ring test commonly used. This paper presents a comprehensive experiment using large ring tests with cast concrete to investigate the impact of upscaling ring test geometry. The two ring specimens demonstrated comparable cracking age (22 days) and strain measured in the steel ring, suggesting that consistent results can be obtained through the proposed instrumentation, calibration, and correction methods. Moreover, the estimated induced tensile stresses of the concrete rings (2.8 and 2.7 MPa) are slightly lower than the predicted tensile strength (3.3 MPa) at the age of cracking, which indicates that some driving forces contributing to restrained shrinkage cracking were not indicated in the strain gauge readings. Furthermore, the study identified multi‐crack formation and additional potential causes for crack initiation, which include self‐restraint due to the moisture gradient in the vertical direction, deflection of the concrete ring caused by its self‐weight, and friction on the contact surface of the support. Therefore, optimising the geometry of the ring specimens and the apparatus is imperative to minimise additional driving forces and unmeasurable restraints for crack initiation, especially when employing the stress rate method to assess cracking potential.
- Open Access
- 15 September 2023
- Published by Elsevier in Tunnelling and Underground Space Technology
- Vol. 142
Spray-applied waterproofing membranes in tunnelling: A construction perspective
- 15 September 2023
- Published by Elsevier in Tunnelling and Underground Space Technology
- Vol. 142
Open AccessSpray-applied waterproofing membranes in tunnelling: A construction perspective