Kee Nam Choo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kee Nam Choo has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Byung-Hyuk Jun
Korea Atomic Energy Research Institute
6 shared publications Man Soon Cho
Korea Atomic Energy Research Institute, Department of Neutron Utilization Technology, 989-111 Daedeokdaero, Yuseong-gu, Daejeon, Korea
5 shared publicationsSeong Woo Yang
Neutron Utilization Technology Division, Korea Atomic Energy Research Institute, Daedeok-daero 989-111, Yuseong-gu, Daejeon, Korea
3 shared publicationsB. G. Kim
Korea Atomic Energy Research Institute, Daejeon, Korea
2 shared publicationsB.G. Kim
2 shared publicationsBong Goo Kim
Korea Atomic Energy Research Institute, Korea Atomic Energy Research Institute Daejeon 305-600, Korea
2 shared publications
Latest Publications
- Open Access
- 8 February 2018
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2018, 1-8
Design Optimization of HANARO Irradiation Capsule for Long-Term Irradiation Testing
As HANARO has been recently required to support new R&D relevant to future nuclear systems requiring much higher neutron fluence, two types of bottom rod tip of the capsule were preliminarily prepared. The first one is a conventional design made of STS304 and welded using a tungsten inert gas (TIG) welding method. The other is a new design made of STS316L and welded using electron beam (EB) welding to strengthen the fatigue property of the rod tip. During the out-pile testing, they failed after 40 and 203 days, respectively. The fracture surfaces were examined using microscopes and the maximal applied stresses were estimated. The combination of these stresses was proved to be sufficient to cause a fatigue failure of the rod tip of the capsule. Based on the failure analysis, an optimized design of the rod tip of the capsule was made for long-term irradiation testing. It was designed to improve the welding and fatigue properties, to decrease the applied stress on the rod tip, and to fundamentally eliminate the effect of residual stress due to welding. The newly designed capsule was safely out-pile-tested up to 450 days and will be utilized for HANARO irradiation testing.
- 8 February 2018
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2018, 1-8
Open AccessDesign Optimization of HANARO Irradiation Capsule for Long-Term Irradiation Testing
As HANARO has been recently required to support new R&D relevant to future nuclear systems requiring much higher neutron fluence, two types of bottom rod tip of the capsule were preliminarily prepared. The first one is a conventional design made of STS304 and welded using a tungsten inert gas (TIG) welding method. The other is a new design made of STS316L and welded using electron beam (EB) welding to strengthen the fatigue property of the rod tip. During the out-pile testing, they failed after 40 and 203 days, respectively. The fracture surfaces were examined using microscopes and the maximal applied stresses were estimated. The combination of these stresses was proved to be sufficient to cause a fatigue failure of the rod tip of the capsule. Based on the failure analysis, an optimized design of the rod tip of the capsule was made for long-term irradiation testing. It was designed to improve the welding and fatigue properties, to decrease the applied stress on the rod tip, and to fundamentally eliminate the effect of residual stress due to welding. The newly designed capsule was safely out-pile-tested up to 450 days and will be utilized for HANARO irradiation testing.
- 1 August 2016
- Published by Taylor & Francis in Nuclear Technology
- Vol. 195 (2) , 213-221
Development of a Low-Temperature Irradiation Capsule for Research Reactor Materials at HANARO
A new capsule design was prepared and tested at the High Flux Advanced Neutron Application Reactor (HANARO) for neutron irradiation of the core materials of research reactors at a low temperature (of <100°C). The capsule was first designed at HANARO to have the coolant flow through the capsule to cool down the irradiation temperature of the specimens. The safety of the newly designed capsule should be fully checked before irradiation testing. Out-pile performance and endurance testing before HANARO irradiation testing was performed using a capsule in the HANARO out-pile test facilities. The new capsule had a much higher coolant flow-induced vibration than a standard capsule, resulting in fatigue failure at the rod tip of the capsule. The lifetime of the rod tip was greatly improved by changing the material from Type 304 stainless steel to Type 316L stainless steel and by changing the welding method from tungsten inert gas welding to electron beam welding. With the optimized design, the capsule was...
- 1 August 2016
- Published by Taylor & Francis in Nuclear Technology
- Vol. 195 (2) , 213-221
Development of a Low-Temperature Irradiation Capsule for Research Reactor Materials at HANARO
A new capsule design was prepared and tested at the High Flux Advanced Neutron Application Reactor (HANARO) for neutron irradiation of the core materials of research reactors at a low temperature (of <100°C). The capsule was first designed at HANARO to have the coolant flow through the capsule to cool down the irradiation temperature of the specimens. The safety of the newly designed capsule should be fully checked before irradiation testing. Out-pile performance and endurance testing before HANARO irradiation testing was performed using a capsule in the HANARO out-pile test facilities. The new capsule had a much higher coolant flow-induced vibration than a standard capsule, resulting in fatigue failure at the rod tip of the capsule. The lifetime of the rod tip was greatly improved by changing the material from Type 304 stainless steel to Type 316L stainless steel and by changing the welding method from tungsten inert gas welding to electron beam welding. With the optimized design, the capsule was...
- Open Access
- 3 February 2016
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 106, 01004
Neutron Flux Characterization of Irradiation Holes for Irradiation Test at HANARO
EPJ Web of Conferences, open-access proceedings in physics and related sciences
- 3 February 2016
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 106, 01004
Open AccessNeutron Flux Characterization of Irradiation Holes for Irradiation Test at HANARO
EPJ Web of Conferences, open-access proceedings in physics and related sciences
- 1 February 2016
- Published by Taylor & Francis in Nuclear Technology
- Vol. 193 (2) , 330-339
Material Irradiation Technology Using Capsules at HANARO
The Korean research program on nuclear technology requires various in-pile tests to evaluate the safety of currently operating nuclear power plants and develop a future nuclear system. HANARO (High-flux Advanced Neutron Application Reactor) provides a peak thermal and fast flux of 5.0 × 1014 n/cm2 · s (E < 0.625 MeV) and 2.1 × 1014 n/cm2 · s (E > 0.821 MeV), respectively, at 30 MW maximum thermal power. A capsule system has been developed for irradiation tests of nuclear materials and fuels at the core region. Extensive efforts have been made to establish the design and manufacturing technology for various capsules and a temperature control system, which should be compatible with HANARO’s characteristics. The capsule system has been actively utilized for various materials and fuel irradiation tests requested by users from research institutes, universities, and industries. Since 1995, more than 10,000 specimens have been irradiated using the developed capsule system. Presently, new irradiation technologies, such as a high-temperature irradiation capsule for a very-high-temperature reactor and a sodium-cooled fast reactor, and a low-temperature irradiation capsule for a research reactor, are being developed. These technologies will be completed with the development of instruments such as a linear variable differential transformer, a micro-electric heater, and a self-powered neutron detector in the near future, and they will be used for the Generation-IV nuclear system in Korea.
- 1 February 2016
- Published by Taylor & Francis in Nuclear Technology
- Vol. 193 (2) , 330-339
Material Irradiation Technology Using Capsules at HANARO
The Korean research program on nuclear technology requires various in-pile tests to evaluate the safety of currently operating nuclear power plants and develop a future nuclear system. HANARO (High-flux Advanced Neutron Application Reactor) provides a peak thermal and fast flux of 5.0 × 1014 n/cm2 · s (E < 0.625 MeV) and 2.1 × 1014 n/cm2 · s (E > 0.821 MeV), respectively, at 30 MW maximum thermal power. A capsule system has been developed for irradiation tests of nuclear materials and fuels at the core region. Extensive efforts have been made to establish the design and manufacturing technology for various capsules and a temperature control system, which should be compatible with HANARO’s characteristics. The capsule system has been actively utilized for various materials and fuel irradiation tests requested by users from research institutes, universities, and industries. Since 1995, more than 10,000 specimens have been irradiated using the developed capsule system. Presently, new irradiation technologies, such as a high-temperature irradiation capsule for a very-high-temperature reactor and a sodium-cooled fast reactor, and a low-temperature irradiation capsule for a research reactor, are being developed. These technologies will be completed with the development of instruments such as a linear variable differential transformer, a micro-electric heater, and a self-powered neutron detector in the near future, and they will be used for the Generation-IV nuclear system in Korea.
- 1 November 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 650, 794-798
Improved transport critical current properties in glycerin-doped MgB2 wire using milled boron powder and a solid-state reaction of 600 °C
- 1 November 2015
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 650, 794-798
Improved transport critical current properties in glycerin-doped MgB2 wire using milled boron powder and a solid-state reaction of 600 °C
- Open Access
- 24 August 2015
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2015, 1-8
Study on the Effects of Liquid Thermal Media on the Irradiation Capsule of High-Temperature Materials
Irradiation tests of materials at HANARO have usually been conducted using a standard capsule at temperatures of about 300°C for irradiation of materials used at PWR. Thus, the standard capsule uses aluminum as the specimen holder, which acts to dissipate the thermal energy. Future nuclear systems such as a VHTR and SFR require the irradiation tests at a relatively high temperature. As an alternative to aluminum which has been used as the thermal media in a standard material capsule, the characteristics of liquid metals such as NaK and LBE are reviewed. The temperatures of the capsule are affected by the variation of parameters such as the gap and wall thickness of the container. In particular, the external gap is most important in determining the temperature of the specimen. LBE raises the temperature of the specimen higher than NaK at the same configuration of the capsule. Thus, LBE can lessen the gap of the parts and reduce the vibration for a stable long-term test in reactor.
- 24 August 2015
- Published by Wiley in Science and Technology of Nuclear Installations
- Vol. 2015, 1-8
Open AccessStudy on the Effects of Liquid Thermal Media on the Irradiation Capsule of High-Temperature Materials
Irradiation tests of materials at HANARO have usually been conducted using a standard capsule at temperatures of about 300°C for irradiation of materials used at PWR. Thus, the standard capsule uses aluminum as the specimen holder, which acts to dissipate the thermal energy. Future nuclear systems such as a VHTR and SFR require the irradiation tests at a relatively high temperature. As an alternative to aluminum which has been used as the thermal media in a standard material capsule, the characteristics of liquid metals such as NaK and LBE are reviewed. The temperatures of the capsule are affected by the variation of parameters such as the gap and wall thickness of the container. In particular, the external gap is most important in determining the temperature of the specimen. LBE raises the temperature of the specimen higher than NaK at the same configuration of the capsule. Thus, LBE can lessen the gap of the parts and reduce the vibration for a stable long-term test in reactor.
- 25 March 2015
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 116 (3) , 242-247
Annealing-induced crystallization of the Er2Fe13.8B alloy amorphized by irradiation
To study the evolution of structural and magnetic states of irradiation-amorphized Er2Fe13.8B alloy during isothermal annealing at temperatures of 295–1025 K, magnetization measurements and neutron...
- 25 March 2015
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 116 (3) , 242-247
Annealing-induced crystallization of the Er2Fe13.8B alloy amorphized by irradiation
To study the evolution of structural and magnetic states of irradiation-amorphized Er2Fe13.8B alloy during isothermal annealing at temperatures of 295–1025 K, magnetization measurements and neutron...
- Open Access
- 1 August 2014
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 46 (4) , 501-512
CONTRIBUTION OF HANARO IRRADIATION TECHNOLOGIES TO NATIONAL NUCLEAR R&D
- 1 August 2014
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 46 (4) , 501-512
Open AccessCONTRIBUTION OF HANARO IRRADIATION TECHNOLOGIES TO NATIONAL NUCLEAR R&D
- 1 July 2014
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 502, 4-9
Reaction-induced pore formation and superconductivity in in situ processed MgB2 superconductors
- 1 July 2014
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 502, 4-9
Reaction-induced pore formation and superconductivity in in situ processed MgB2 superconductors
- 30 June 2014
- Published by The Korea Institute of Applied Superconductivity and Cryogenics in Progress in Superconductivity and Cryogenics
- Vol. 16 (2) , 36-41
Tcand Jcdistribution in in situ processed MgB2bulk superconductors with/without C doping
- 30 June 2014
- Published by The Korea Institute of Applied Superconductivity and Cryogenics in Progress in Superconductivity and Cryogenics
- Vol. 16 (2) , 36-41
Tcand Jcdistribution in in situ processed MgB2bulk superconductors with/without C doping