Shiqiang Duan
Research Subjects
Shiqiang Duan has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Hua Zheng
School of Power and Energy, Northwestern Polytechnical University, Xi’an, China
5 shared publications Junhao Liu
School of Power and Energy, Northwestern Polytechnical University, Shaan Xi, Xi’an 710072, P. R. China
3 shared publications- Guanyu Fang
School of Power and Energy, Northwestern Polytechnical University, Shaanxi, Xi’an 710072, China
1 shared publication - Jiangtao Zhou
AInnovation, Beijing 100080, China
1 shared publication - Jianzhu Wang
School of Power and Energy, Northwestern Polytechnical University, Shaanxi, Xi’an 710072, China
1 shared publication Liu Junhao
School of Power and Energy, Northwestern Polytechnical University, Xi’an, Shaan xi, 710072, China
1 shared publication
Latest Publications
- Open Access
- 11 June 2022
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2022, 1-18
Model Parameter Estimation Method on Multichannel Structural Response from Turbulence Flutter Test
Flutter design is important for the design of new aircraft types, for which flutter tests are an important verification measure. Atmospheric turbulence excitation is a common form of excitation in flutter flight tests. The modal parameter estimation of the turbulence response is a key aspect to ensure accurate data processing of flutter test results. Atmospheric turbulence excitation acts on the structural system, and the turbulence response thus simultaneously contains both the randomness of the excitation signal and the determinism of the structure system. In view of the turbulence response characteristics, this paper addresses the incoherence of atmospheric turbulence excitation and the orthogonality of the frequency domain from a multichannel response. The turbulence response is used to perform modal parameter identification in the frequency domain. The power spectral density matrix can be calculated from the multichannel turbulence response using the periodogram method. Singular value decomposition is then performed on the power spectral density matrix at each spectral pin based on the orthogonality of the frequency domain. The maximum singular value of each spectral pin forms a curve over the entire frequency band, which is the autopower spectral density function of the system, the system is directly identified at the frequency domain using the polynomial fitting in the frequency domain, and the modal parameters (frequency, damping ratio) are calculated according to the fitted transfer function. This paper verifies the theoretical feasibility of the proposed method using simulation data. The engineering applicability is verified based on the turbulence response from the flutter flight test of a certain aircraft type.
- 11 June 2022
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2022, 1-18
Open AccessModel Parameter Estimation Method on Multichannel Structural Response from Turbulence Flutter Test
Flutter design is important for the design of new aircraft types, for which flutter tests are an important verification measure. Atmospheric turbulence excitation is a common form of excitation in flutter flight tests. The modal parameter estimation of the turbulence response is a key aspect to ensure accurate data processing of flutter test results. Atmospheric turbulence excitation acts on the structural system, and the turbulence response thus simultaneously contains both the randomness of the excitation signal and the determinism of the structure system. In view of the turbulence response characteristics, this paper addresses the incoherence of atmospheric turbulence excitation and the orthogonality of the frequency domain from a multichannel response. The turbulence response is used to perform modal parameter identification in the frequency domain. The power spectral density matrix can be calculated from the multichannel turbulence response using the periodogram method. Singular value decomposition is then performed on the power spectral density matrix at each spectral pin based on the orthogonality of the frequency domain. The maximum singular value of each spectral pin forms a curve over the entire frequency band, which is the autopower spectral density function of the system, the system is directly identified at the frequency domain using the polynomial fitting in the frequency domain, and the modal parameters (frequency, damping ratio) are calculated according to the fitted transfer function. This paper verifies the theoretical feasibility of the proposed method using simulation data. The engineering applicability is verified based on the turbulence response from the flutter flight test of a certain aircraft type.
- Open Access
- 27 February 2021
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2021, 1-10
Research on Feature Extracted Method for Flutter Test Based on EMD and CNN
Due to the inevitable deviations between the results of theoretical calculations and physical experiments, flutter tests and flutter signal analysis often play significant roles in designing the aeroelasticity of a new aircraft. The measured structural response from aeroelastic models in both wind tunnel tests and real fight flutter tests contain an abundance of structural information, but traditional methods tend to have limited ability to extract features of concern. Inspired by deep learning concepts, a novel feature extraction method for flutter signal analysis was established in this study by combining the convolutional neural network (CNN) with empirical mode decomposition (EMD). It is widely hypothesized that when flutter occurs, the measured structural signals are harmonic or divergent in the time domain, and that the flutter modal (1) is singular and (2) its energy increases significantly in the frequency domain. A measured-signal feature extraction and flutter criterion framework was constructed accordingly. The measured signals from a wind tunnel test were manually labeled “flutter” and “no-flutter” as the foundational dataset for the deep learning algorithm. After the normalized preprocessing, the intrinsic mode functions (IMFs) of the flutter test signals are obtained by the EMD method. The IMFs are then reshaped to make them the suitable size to be input to the CNN. The CNN parameters are optimized though the training dataset, and the trained model is validated through the test dataset (i.e., cross-validation). The accuracy rate of the proposed method reached 100% on the test dataset. The training model appears to effectively distinguish whether or not the structural response signal contains flutter. The combination of EMD and CNN provides effective feature extraction of time series signals in flutter test data. This research explores the connection between structural response signals and flutter from the perspective of artificial intelligence. The method allows for real-time, online prediction with low computational complexity.
- 27 February 2021
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2021, 1-10
Open AccessResearch on Feature Extracted Method for Flutter Test Based on EMD and CNN
Due to the inevitable deviations between the results of theoretical calculations and physical experiments, flutter tests and flutter signal analysis often play significant roles in designing the aeroelasticity of a new aircraft. The measured structural response from aeroelastic models in both wind tunnel tests and real fight flutter tests contain an abundance of structural information, but traditional methods tend to have limited ability to extract features of concern. Inspired by deep learning concepts, a novel feature extraction method for flutter signal analysis was established in this study by combining the convolutional neural network (CNN) with empirical mode decomposition (EMD). It is widely hypothesized that when flutter occurs, the measured structural signals are harmonic or divergent in the time domain, and that the flutter modal (1) is singular and (2) its energy increases significantly in the frequency domain. A measured-signal feature extraction and flutter criterion framework was constructed accordingly. The measured signals from a wind tunnel test were manually labeled “flutter” and “no-flutter” as the foundational dataset for the deep learning algorithm. After the normalized preprocessing, the intrinsic mode functions (IMFs) of the flutter test signals are obtained by the EMD method. The IMFs are then reshaped to make them the suitable size to be input to the CNN. The CNN parameters are optimized though the training dataset, and the trained model is validated through the test dataset (i.e., cross-validation). The accuracy rate of the proposed method reached 100% on the test dataset. The training model appears to effectively distinguish whether or not the structural response signal contains flutter. The combination of EMD and CNN provides effective feature extraction of time series signals in flutter test data. This research explores the connection between structural response signals and flutter from the perspective of artificial intelligence. The method allows for real-time, online prediction with low computational complexity.
- 7 June 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Pattern Recognition and Artificial Intelligence
- Vol. 33 (07)
Online EMD-Wavelet Method for Flutter Test Excited by Atmospheric Turbulence
Empirical Mode Decomposition (EMD) and Wavelet method have been widely used in the vibration signal analysis, mainly because of the powerful ability of blind modal separation. In the flutter test, modal identification and modal trajectories tracking online can help to ensure the test safety. However, traditional EMD method is only suitable for offline data batching, which limits its applications to the real-time or near real-time signal analysis. For this reason, according to the online processing requirements of flutter test under the turbulent excitation conditions, combining with wavelet spectrum analysis, an online EMD method based on a sliding window for structural modal identification and flutter boundary prediction (FBP) is proposed in this paper. The corresponding mathematical principles and implementation algorithms are given as well, which decompose the measured signal into the Intrinsic Mode Function (IMF) firstly, and then estimate the modal parameters by using the wavelet power spectrum method. The FBP result is typically obtained online during the test process by using curve fitting and extrapolation of the modal damping. The numerical simulations and test data from a low-speed wind tunnel flutter test are used to verify the effectiveness and engineering feasibility of the proposed method.
- 7 June 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Pattern Recognition and Artificial Intelligence
- Vol. 33 (07)
Online EMD-Wavelet Method for Flutter Test Excited by Atmospheric Turbulence
Empirical Mode Decomposition (EMD) and Wavelet method have been widely used in the vibration signal analysis, mainly because of the powerful ability of blind modal separation. In the flutter test, modal identification and modal trajectories tracking online can help to ensure the test safety. However, traditional EMD method is only suitable for offline data batching, which limits its applications to the real-time or near real-time signal analysis. For this reason, according to the online processing requirements of flutter test under the turbulent excitation conditions, combining with wavelet spectrum analysis, an online EMD method based on a sliding window for structural modal identification and flutter boundary prediction (FBP) is proposed in this paper. The corresponding mathematical principles and implementation algorithms are given as well, which decompose the measured signal into the Intrinsic Mode Function (IMF) firstly, and then estimate the modal parameters by using the wavelet power spectrum method. The FBP result is typically obtained online during the test process by using curve fitting and extrapolation of the modal damping. The numerical simulations and test data from a low-speed wind tunnel flutter test are used to verify the effectiveness and engineering feasibility of the proposed method.
- Open Access
- 25 October 2018
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2018, 1-12
Novel Nonstationarity Assessment Method for Hypersonic Flutter Flight Tests
Hypersonic aircraft have been rapidly developed in recent years both theoretically and experimentally. Aerothermoelastic simulation is very challenging due to its inherent complexity, but physical tests are a workable approach. Flutter tests with variable speed are a popular alternative to hypersonic tests which provide nonstationary structural response data. This paper proposes a nonstationarity assessment method based on energy distribution in the time-frequency domain. The proposed method reveals the nonstationarity level corresponding to the appropriate modal identification algorithm or flutter boundary prediction (FBP) method. Several classic flutter criteria are utilized to build a hypersonic aircraft FBP framework. Numerical simulation and experimental applications demonstrate the effectiveness and feasibility of the proposed method, which facilitates accurate flutter predictions for the subcritical turbulence response during hypersonic flutter flight.
- 25 October 2018
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2018, 1-12
Open AccessNovel Nonstationarity Assessment Method for Hypersonic Flutter Flight Tests
Hypersonic aircraft have been rapidly developed in recent years both theoretically and experimentally. Aerothermoelastic simulation is very challenging due to its inherent complexity, but physical tests are a workable approach. Flutter tests with variable speed are a popular alternative to hypersonic tests which provide nonstationary structural response data. This paper proposes a nonstationarity assessment method based on energy distribution in the time-frequency domain. The proposed method reveals the nonstationarity level corresponding to the appropriate modal identification algorithm or flutter boundary prediction (FBP) method. Several classic flutter criteria are utilized to build a hypersonic aircraft FBP framework. Numerical simulation and experimental applications demonstrate the effectiveness and feasibility of the proposed method, which facilitates accurate flutter predictions for the subcritical turbulence response during hypersonic flutter flight.
- Open Access
- 12 August 2018
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2018, 1-8
Flutter Test Data Processing Based on Improved Hilbert-Huang Transform
Flutter tests are conducted primarily for the purpose of modal parameter estimation and flutter boundary prediction, the accuracy of which is severely affected by the acquired data quality, structural modal density, and nonstationary conditions. An improved Hilbert-Huang Transform (HHT) algorithm is presented in this paper which mitigates the typical mode mixing effect via modulation. The algorithm is validated by theory, by numerical simulation, and per actual flight flutter test data. The results show that the proposed method could extract the flutter model parameters and predict the flutter speed more accurately, which is feasible for the current flutter test data processing.
- 12 August 2018
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2018, 1-8
Open AccessFlutter Test Data Processing Based on Improved Hilbert-Huang Transform
Flutter tests are conducted primarily for the purpose of modal parameter estimation and flutter boundary prediction, the accuracy of which is severely affected by the acquired data quality, structural modal density, and nonstationary conditions. An improved Hilbert-Huang Transform (HHT) algorithm is presented in this paper which mitigates the typical mode mixing effect via modulation. The algorithm is validated by theory, by numerical simulation, and per actual flight flutter test data. The results show that the proposed method could extract the flutter model parameters and predict the flutter speed more accurately, which is feasible for the current flutter test data processing.
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 430-434
A Preprocessing Method for Flutter Signals Based on Morphological Filtering
The analysis on the test data is an important way to obtain the flutter characteristics of aircraft. Because of the low quality of the measured signal, the preprocessing is indispensable to improve the accuracy of flutter data analysis. In this paper, the morphological filtering is introduced into the field of flutter structure data processing. The theory of mathematical morphology is given, and the effectiveness of morphological filtering depending on the different operation types and structural elements are discussed. After that, the typical flutter boundary prediction (FBP) method is used to verify the validity and feasibility of the morphological preprocessing method through the numerical simulations, as well as the flight flutter test data. The results is shown that the morphological filtering can enhance Signal to Noise Rate (SNR) of the measured structural response from the physical test in terms of improving the prediction accuracy in actually engineering applications.
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 430-434
A Preprocessing Method for Flutter Signals Based on Morphological Filtering
The analysis on the test data is an important way to obtain the flutter characteristics of aircraft. Because of the low quality of the measured signal, the preprocessing is indispensable to improve the accuracy of flutter data analysis. In this paper, the morphological filtering is introduced into the field of flutter structure data processing. The theory of mathematical morphology is given, and the effectiveness of morphological filtering depending on the different operation types and structural elements are discussed. After that, the typical flutter boundary prediction (FBP) method is used to verify the validity and feasibility of the morphological preprocessing method through the numerical simulations, as well as the flight flutter test data. The results is shown that the morphological filtering can enhance Signal to Noise Rate (SNR) of the measured structural response from the physical test in terms of improving the prediction accuracy in actually engineering applications.