Robert Głębocki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Robert Głębocki has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Mariusz Jacewicz
Warsaw University of Technology
12 shared publications - Antoni Kopyt
Warsaw University of Technology
4 shared publications - Dariusz Miedziński
Warsaw University of Technology
4 shared publications - Rafał Ożóg
Warsaw University of Technology
3 shared publications - Adrian Szklarski
Warsaw University of Technology
2 shared publications - Dariusz Miedziński
Warsaw University of Technology
2 shared publications
Latest Publications
- Open Access
- 21 September 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 20 (3) , 105-117
An Efficient Swarm Control Algorithm for Covering an Area With Communication Network
There is an increase in popularity of Unmanned Aerial Vehicles that can fly in autonomous swarms. Many applications, such as surveillance, disaster response or enabling of wireless access networks can be found for such drones. In this work an efficient swarm control algorithm for establishing a WiFi network over a specified area in emergency situations was prepared and tested in a developed swarm simulator. The test results show that the area can be effectively and fully covered by the drone formations, without in-flight collisions, and keeping the necessary distances between the drones.
- 21 September 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 20 (3) , 105-117
Open AccessAn Efficient Swarm Control Algorithm for Covering an Area With Communication Network
There is an increase in popularity of Unmanned Aerial Vehicles that can fly in autonomous swarms. Many applications, such as surveillance, disaster response or enabling of wireless access networks can be found for such drones. In this work an efficient swarm control algorithm for establishing a WiFi network over a specified area in emergency situations was prepared and tested in a developed swarm simulator. The test results show that the area can be effectively and fully covered by the drone formations, without in-flight collisions, and keeping the necessary distances between the drones.
- Open Access
- 25 November 2025
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- p. 583-606
Aerodynamic control analysis in a canard configuration for a surface-to-surface missile
The modern battlefield requires highly accurate missiles, which has led to the modification of unguided missiles into guided versions. This paper presents the process of adapting an unguided missile with a range of 40 km into a guided version using a canard control system. A key aspect of the upgrade was the development of a control system that allows the trajectory to be corrected after crossing the apex of the flight path, particularly during the descent phase. This paper discusses the design details and application of a two-channel control system (pitch and yaw) in which the control signals are synchronized with the speed of the projectile. Mathematical modelling and numerical simulations have shown that, with appropriate control parameters, a zero mean control force can be achieved, leading to trajectory stabilization and minimized aiming errors. The proposed solution provides a basis for further research and dynamic field tests and can contribute to the development of precision guidance technology for surface-to-surface missiles.
- 25 November 2025
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- p. 583-606
Open AccessAerodynamic control analysis in a canard configuration for a surface-to-surface missile
The modern battlefield requires highly accurate missiles, which has led to the modification of unguided missiles into guided versions. This paper presents the process of adapting an unguided missile with a range of 40 km into a guided version using a canard control system. A key aspect of the upgrade was the development of a control system that allows the trajectory to be corrected after crossing the apex of the flight path, particularly during the descent phase. This paper discusses the design details and application of a two-channel control system (pitch and yaw) in which the control signals are synchronized with the speed of the projectile. Mathematical modelling and numerical simulations have shown that, with appropriate control parameters, a zero mean control force can be achieved, leading to trajectory stabilization and minimized aiming errors. The proposed solution provides a basis for further research and dynamic field tests and can contribute to the development of precision guidance technology for surface-to-surface missiles.
- 30 October 2025
- Published by Springer Nature
- p. 255-267
Algorithms for Calculating Navigation Data of Rotating Missiles
- 30 October 2025
- Published by Springer Nature
- p. 255-267
Algorithms for Calculating Navigation Data of Rotating Missiles
- Open Access
Analytical Shaping of a Rocket Nose as a Stage of Preliminary Aerodynamic Modification
The article discusses the problem of a preliminary analytical method for modifying the shape of a rocket’s nose. The purpose of this method is to determine the shape that minimizes aerodynamic drag, in the context of modifying a ballistic missile to incorporate guidance systems. The traditional design process relies on numerical methods such as CFD (Computational Fluid Dynamics) or machine learning techniques; however, the method presented here can serve as a first iteration to support the design. Advanced simulation tools are often expensive and difficult to access for smaller companies, while open-source software can sometimes be unreliable, difficult to use, and incompatible with professional solutions. This can pose a challenge for businesses planning to collaborate in the future with large corporations that rely on advanced engineering tools. The proposed solution, as previously mentioned, provides a starting point for the entire design process. The approach has been shown to be sufficient from the design work. The entire process was validated during test range trials, during which rockets were launched, and the flight measurement results accurately reflected the aerodynamic properties of the missiles. In the next stages of the project, numerical methods including CFD simulations are planned to verify the analytical results and enable further aerodynamic modification of the design.
Open AccessAnalytical Shaping of a Rocket Nose as a Stage of Preliminary Aerodynamic Modification
The article discusses the problem of a preliminary analytical method for modifying the shape of a rocket’s nose. The purpose of this method is to determine the shape that minimizes aerodynamic drag, in the context of modifying a ballistic missile to incorporate guidance systems. The traditional design process relies on numerical methods such as CFD (Computational Fluid Dynamics) or machine learning techniques; however, the method presented here can serve as a first iteration to support the design. Advanced simulation tools are often expensive and difficult to access for smaller companies, while open-source software can sometimes be unreliable, difficult to use, and incompatible with professional solutions. This can pose a challenge for businesses planning to collaborate in the future with large corporations that rely on advanced engineering tools. The proposed solution, as previously mentioned, provides a starting point for the entire design process. The approach has been shown to be sufficient from the design work. The entire process was validated during test range trials, during which rockets were launched, and the flight measurement results accurately reflected the aerodynamic properties of the missiles. In the next stages of the project, numerical methods including CFD simulations are planned to verify the analytical results and enable further aerodynamic modification of the design.
- 5 February 2023
- Published by Springer Nature
- p. 39-50
Analysis of Sounding Rocket Dispersion Using Monte-Carlo Simulation
- 5 February 2023
- Published by Springer Nature
- p. 39-50
Analysis of Sounding Rocket Dispersion Using Monte-Carlo Simulation
- Open Access
- 5 December 2022
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (1) , 151-178
Validation of the energy consumption model for a quadrotor using Monte-Carlo simulation
Unmanned, battery-powered quadrotors have a limited onboard energy resources. However, flight duration might be increased by reasonable energy expenditure. A reliable mathematical model of the drone is required to plan the optimum energy management during the mission. In this paper, the theoretical energy consumption model was proposed. A small, low-cost DJI MAVIC 2 Pro quadrotor was used as a test platform. Model parameters were obtained experimentally in laboratory conditions. Next, the model was implemented in MATLAB/Simulink and then validated using the data collected during real flight trials in outdoor conditions. Finally, the Monte-Carlo simulation was used to evaluate the model reliability in the presence of modeling uncertainties. It was obtained that the parameter uncertainties could affect the amount of total consumed energy by less than 8% of the nominal value. The presented model of energy consumption might be practically used to predict energy expenditure, battery state of charge, and voltage in a typical mission of a drone.
- 5 December 2022
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (1) , 151-178
Open AccessValidation of the energy consumption model for a quadrotor using Monte-Carlo simulation
Unmanned, battery-powered quadrotors have a limited onboard energy resources. However, flight duration might be increased by reasonable energy expenditure. A reliable mathematical model of the drone is required to plan the optimum energy management during the mission. In this paper, the theoretical energy consumption model was proposed. A small, low-cost DJI MAVIC 2 Pro quadrotor was used as a test platform. Model parameters were obtained experimentally in laboratory conditions. Next, the model was implemented in MATLAB/Simulink and then validated using the data collected during real flight trials in outdoor conditions. Finally, the Monte-Carlo simulation was used to evaluate the model reliability in the presence of modeling uncertainties. It was obtained that the parameter uncertainties could affect the amount of total consumed energy by less than 8% of the nominal value. The presented model of energy consumption might be practically used to predict energy expenditure, battery state of charge, and voltage in a typical mission of a drone.
- Open Access
Quadrotor Model for Energy Consumption Analysis
In this paper, a quadrotor dynamic model’s energy efficiency was investigated. A method for the design of the dynamic model which assures energy consumption estimation was presented. This model was developed to analyze the energy efficiency of the quadrotor during each maneuver. A medium-class quadrotor (4.689 kg) was used as a test platform. Thrust force correction factors obtained with FLIGHTLAB software were used to predict object behavior in forward flight. Model validation and long-duration flight tests in outdoor windy conditions are also presented. Monte-Carlo simulation was used to study the influence of uncertainties in model parameters on the simulation reliability. The developed model might be used for practical purposes (for example, energy-efficient coverage path planning).
Open AccessQuadrotor Model for Energy Consumption Analysis
In this paper, a quadrotor dynamic model’s energy efficiency was investigated. A method for the design of the dynamic model which assures energy consumption estimation was presented. This model was developed to analyze the energy efficiency of the quadrotor during each maneuver. A medium-class quadrotor (4.689 kg) was used as a test platform. Thrust force correction factors obtained with FLIGHTLAB software were used to predict object behavior in forward flight. Model validation and long-duration flight tests in outdoor windy conditions are also presented. Monte-Carlo simulation was used to study the influence of uncertainties in model parameters on the simulation reliability. The developed model might be used for practical purposes (for example, energy-efficient coverage path planning).
- Open Access
Wavelet-Based Identification for Spinning Projectile with Gasodynamic Control Aerodynamic Coefficients Determination
Identification of a spinning projectile controlled with gasodynamic engines is shown in this paper. A missile model with a measurement inertial unit was developed from Newton’s law of motion and its aerodynamic coefficients were identified. This was achieved by applying the maximum likelihood principle in the wavelet domain. To assess the results, this was also performed in the time domain. The outcomes were obtained for two cases: when noise was not present and when it was included in the data. In all cases, the identification was performed in the passive mode, i.e., no special system identification experiments were designed. In the noise-free case, aerodynamic coefficients were estimated with high accuracy. When noise was included in the data, the wavelet-based estimates had a drop in their accuracy, but were still very accurate, whereas for the time domain approach the estimates were considered inaccurate.
Open AccessWavelet-Based Identification for Spinning Projectile with Gasodynamic Control Aerodynamic Coefficients Determination
Identification of a spinning projectile controlled with gasodynamic engines is shown in this paper. A missile model with a measurement inertial unit was developed from Newton’s law of motion and its aerodynamic coefficients were identified. This was achieved by applying the maximum likelihood principle in the wavelet domain. To assess the results, this was also performed in the time domain. The outcomes were obtained for two cases: when noise was not present and when it was included in the data. In all cases, the identification was performed in the passive mode, i.e., no special system identification experiments were designed. In the noise-free case, aerodynamic coefficients were estimated with high accuracy. When noise was included in the data, the wavelet-based estimates had a drop in their accuracy, but were still very accurate, whereas for the time domain approach the estimates were considered inaccurate.
- Open Access
Study of Model Uncertainties Influence on the Impact Point Dispersion for a Gasodynamicaly Controlled Projectile
The article presents the analysis of the impact point dispersion reduction using lateral correction thrusters. Two types of control algorithms are used and four sources of uncertainties are taken into account: aerodynamic parameters, thrust curve, initial conditions and IMU errors. The Monte Carlo approach was used for simulations and Circular Error Probable was used as a measure of dispersion. Generic rocket mathematical and simulation model was created in MATLAB/Simulink 2020b environment. Results show that the use of control algorithms greatly reduces the impact point dispersion.
Open AccessStudy of Model Uncertainties Influence on the Impact Point Dispersion for a Gasodynamicaly Controlled Projectile
The article presents the analysis of the impact point dispersion reduction using lateral correction thrusters. Two types of control algorithms are used and four sources of uncertainties are taken into account: aerodynamic parameters, thrust curve, initial conditions and IMU errors. The Monte Carlo approach was used for simulations and Circular Error Probable was used as a measure of dispersion. Generic rocket mathematical and simulation model was created in MATLAB/Simulink 2020b environment. Results show that the use of control algorithms greatly reduces the impact point dispersion.