Mengjia Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mengjia Hu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jiluan Pan
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
2 shared publications - Kejian Li
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
2 shared publications - Shanlin Li
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
2 shared publications - Zhipeng Cai
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
2 shared publications - Yao Wu
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
1 shared publication
Latest Publications
- Open Access
Analytical Model to Compare and Select Creep Constitutive Equation for Stress Relief Investigation during Heat Treatment in Ferritic Welded Structure
The one-dimensional analytical model was promoted to help select the creep constitutive equation and predict heat treatment temperature in a ferritic welded structure, along with neglecting the impact of structural constraint and deformation compatibility. The analytical solutions were compared with simulation results, which were validated with experimental measurements in a ferritic welded rotor. The as-welded and post weld heat treatment (PWHT) residual stresses on the inner and outer cylindrical surfaces were measured with the hole-drilling method (HDM) for validation. Based on the one-dimensional analytical model, different effects of Norton and Norton-Bailey creep constitutive equation on stress relief during heat treatment in a ferritic welded rotor were investigated.
Open AccessAnalytical Model to Compare and Select Creep Constitutive Equation for Stress Relief Investigation during Heat Treatment in Ferritic Welded Structure
The one-dimensional analytical model was promoted to help select the creep constitutive equation and predict heat treatment temperature in a ferritic welded structure, along with neglecting the impact of structural constraint and deformation compatibility. The analytical solutions were compared with simulation results, which were validated with experimental measurements in a ferritic welded rotor. The as-welded and post weld heat treatment (PWHT) residual stresses on the inner and outer cylindrical surfaces were measured with the hole-drilling method (HDM) for validation. Based on the one-dimensional analytical model, different effects of Norton and Norton-Bailey creep constitutive equation on stress relief during heat treatment in a ferritic welded rotor were investigated.
- Open Access
The Mechanism for HAZ Liquation of Nickel-Based Alloy 617B During Gas Tungsten Arc Welding
The mechanism for HAZ (heat-affected zone) liquation of alloy 617B during gas tungsten arc welding (GTAW) was investigated. Welding thermal simulation work was conducted to investigate the effects of thermal parameters (peak temperature, holding time, and thermal cycle numbers) on M23C6 carbides’ evolutionary behavior in nickel-based alloy 617B. OM (optical microscopy), SEM (scanning electron microscopy), TEM (transmission electron microscopy), and SIMS (secondary ion mass spectrometry) were employed to characterize HAZ carbides. It was found that the constitutional liquation of M23C6 carbides is responsible for HAZ liquation in alloy 617B. Rapid heating meant that solute atoms released from partially dissolved M23C6 carbides did not have enough time to sufficiently diffuse into the matrix, resulting in eutectic reaction M23C6 + γ → liquid in the temperature range from 1250 °C to 1300 °C. In the following cooling process, the liquid phase transformed into γ and M23C6 (or M6C) carbides simultaneously, creating a eutectic microstructure. Subsequent thermal cycles with peak temperature 1100 °C and proper holding time brought about a tempering effect to precipitate fine M23C6 carbides from the Cr supersaturated zone around the eutectic microstructure. Boron was found to be enriched in carbides and was expected to promote HAZ liquation by two mechanisms. No cracking caused by HAZ liquation has been found, indicating that GTAW is a suitable method for joining alloy 617B.
Open AccessThe Mechanism for HAZ Liquation of Nickel-Based Alloy 617B During Gas Tungsten Arc Welding
The mechanism for HAZ (heat-affected zone) liquation of alloy 617B during gas tungsten arc welding (GTAW) was investigated. Welding thermal simulation work was conducted to investigate the effects of thermal parameters (peak temperature, holding time, and thermal cycle numbers) on M23C6 carbides’ evolutionary behavior in nickel-based alloy 617B. OM (optical microscopy), SEM (scanning electron microscopy), TEM (transmission electron microscopy), and SIMS (secondary ion mass spectrometry) were employed to characterize HAZ carbides. It was found that the constitutional liquation of M23C6 carbides is responsible for HAZ liquation in alloy 617B. Rapid heating meant that solute atoms released from partially dissolved M23C6 carbides did not have enough time to sufficiently diffuse into the matrix, resulting in eutectic reaction M23C6 + γ → liquid in the temperature range from 1250 °C to 1300 °C. In the following cooling process, the liquid phase transformed into γ and M23C6 (or M6C) carbides simultaneously, creating a eutectic microstructure. Subsequent thermal cycles with peak temperature 1100 °C and proper holding time brought about a tempering effect to precipitate fine M23C6 carbides from the Cr supersaturated zone around the eutectic microstructure. Boron was found to be enriched in carbides and was expected to promote HAZ liquation by two mechanisms. No cracking caused by HAZ liquation has been found, indicating that GTAW is a suitable method for joining alloy 617B.