Marco P. Luna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marco P. Luna has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Alejandra Staller
Universidad Politécnica de Madrid, ETSI Topografía, Geodesia y Cartografía, Res. Gr. TERRA: Geomatics, NaturalHazards and Risks, Madrid, 28031, Spain
4 shared publications - Theofilos Toulkeridis
Universidad de las Fuerzas Armadas ESPE
4 shared publications - José Antonio Álvarez-Gómez
Department of Geodynamics, Stratigraphy and Paleontology, Universidad Complutense de Madrid, Madrid, Spain
2 shared publications - Marta Béjar-Pizarro
Instituto Geológico y Minero de España (IGME-CSIC), Madrid, 28003, Spain
2 shared publications - Oscar Portilla
Geoint CÍA. LTDA
2 shared publications - Sandra Martínez-Cuevas
Universidad Politécnica de Madrid
2 shared publications
Latest Publications
- Open Access
- 24 August 2023
- Published by Salesian Polytechnic University of Ecuador in La Granja
- Vol. 38 (2) , 59-81
Evaluación de los modelos digitales de terreno y geopotenciales en el Ecuador
Engineering uses digital elevation models to perform calculations and modeling phenomena, since it allows determining the scale at which they can be used and the quality of the by-products obtained. Two groups of models were evaluated, the digital terrain models (DTMs): Shuttle Radar Topography Mission (SRTM), ASTER Global Digital Elevation Map (ASTER GDEM), ALOS PALSAR and the DTM generated by the Instituto Geográfico Militar del Ecuador (IGM), and the geopotential models (GMs): EGM96, EGM08 and the GM created by the IGM. For the evaluation, the geometric leveling points and ellipsoidal height raised in one of the IGM projects were used to determine atypical values, calculate the mean square error (RMSE) and define the precision and scale at which the different ones can be used. The heights between the DTMs were compared to know their difference. It was determined that the SRTM 30, ALOS PALSAR and IGM DMTs can be used for jobs that require an accuracy of less than 10 meters. The GM EGM08 together with high precision ellipsoidal heights could generate elevation models that can reach an accuracy of 1.25 meters, while the GMs EGM96 and IGM can generate models that achieve an accuracy of 2.5 meters. The ellipsoidal heights of the SRTM 30, ALOS PALSAR and IGM DTMs obtained with the EGM 96 and EGM 08 GMs can only be used in jobs that require an accuracy of less than 10 meters.
- 24 August 2023
- Published by Salesian Polytechnic University of Ecuador in La Granja
- Vol. 38 (2) , 59-81
Open AccessEvaluación de los modelos digitales de terreno y geopotenciales en el Ecuador
Engineering uses digital elevation models to perform calculations and modeling phenomena, since it allows determining the scale at which they can be used and the quality of the by-products obtained. Two groups of models were evaluated, the digital terrain models (DTMs): Shuttle Radar Topography Mission (SRTM), ASTER Global Digital Elevation Map (ASTER GDEM), ALOS PALSAR and the DTM generated by the Instituto Geográfico Militar del Ecuador (IGM), and the geopotential models (GMs): EGM96, EGM08 and the GM created by the IGM. For the evaluation, the geometric leveling points and ellipsoidal height raised in one of the IGM projects were used to determine atypical values, calculate the mean square error (RMSE) and define the precision and scale at which the different ones can be used. The heights between the DTMs were compared to know their difference. It was determined that the SRTM 30, ALOS PALSAR and IGM DMTs can be used for jobs that require an accuracy of less than 10 meters. The GM EGM08 together with high precision ellipsoidal heights could generate elevation models that can reach an accuracy of 1.25 meters, while the GMs EGM96 and IGM can generate models that achieve an accuracy of 2.5 meters. The ellipsoidal heights of the SRTM 30, ALOS PALSAR and IGM DTMs obtained with the EGM 96 and EGM 08 GMs can only be used in jobs that require an accuracy of less than 10 meters.
- 29 January 2023
- Published by Springer Nature
- p. 104-117
Proposal for a Unique Cartographic Projection System for the Galapagos Islands in Order to Generate Cartography at Large Scales
- 29 January 2023
- Published by Springer Nature
- p. 104-117
Proposal for a Unique Cartographic Projection System for the Galapagos Islands in Order to Generate Cartography at Large Scales
- Open Access
- 1 January 2023
- Published by Universidad de Los Andes, Venezuela in REVISTA GEOGRÁFICA VENEZOLANA
- Vol. 64 (1) , 22-35
Analysis of statistical interpolation methods to generate the velocities model for continental Ecuador from GNSS data
- 1 January 2023
- Published by Universidad de Los Andes, Venezuela in REVISTA GEOGRÁFICA VENEZOLANA
- Vol. 64 (1) , 22-35
Open AccessAnalysis of statistical interpolation methods to generate the velocities model for continental Ecuador from GNSS data
- Open Access
- 1 January 2021
- Published by Universidad de Los Andes, Venezuela in REVISTA GEOGRÁFICA VENEZOLANA
- Vol. 62 (1) , 176-196
Desarrollo de un sistema de proyección local en el Ecuador continental para la generación de cartografía a detalle
- 1 January 2021
- Published by Universidad de Los Andes, Venezuela in REVISTA GEOGRÁFICA VENEZOLANA
- Vol. 62 (1) , 176-196
Open AccessDesarrollo de un sistema de proyección local en el Ecuador continental para la generación de cartografía a detalle
- 1 October 2018
- Published by Elsevier in Journal of South American Earth Sciences
- Vol. 86, 94-109
Crustal motion and deformation in Ecuador from cGNSS time series
- 1 October 2018
- Published by Elsevier in Journal of South American Earth Sciences
- Vol. 86, 94-109
Crustal motion and deformation in Ecuador from cGNSS time series
- Open Access
- 7 June 2018
- Published by MDPI AG in Remote Sensing
- Vol. 10 (6) , 899
InSAR-Based Mapping to Support Decision-Making after an Earthquake
It has long been recognized that earthquakes change the stress in the upper crust around the fault rupture and can influence the behaviour of neighbouring faults and volcanoes. Rapid estimates of these stress changes can provide the authorities managing the post-disaster situation with valuable data to identify and monitor potential threads and to update the estimates of seismic and volcanic hazard in a region. Here we propose a methodology to evaluate the potential influence of an earthquake on nearby faults and volcanoes and create easy-to-understand maps for decision-making support after large earthquakes. We apply this methodology to the Mw 7.8, 2016 Ecuador earthquake. Using Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) and continuous GPS data, we measure the coseismic ground deformation and estimate the distribution of slip over the fault rupture. We also build an alternative source model using the Global Centroid Moment Tensor (CMT) solution. Then we use these models to evaluate changes of static stress on the surrounding faults and volcanoes and produce maps of potentially activated faults and volcanoes. We found, in general, good agreement between our maps and the seismic and volcanic events that occurred after the Pedernales earthquake. We discuss the potential and limitations of the methodology.
- 7 June 2018
- Published by MDPI AG in Remote Sensing
- Vol. 10 (6) , 899
Open AccessInSAR-Based Mapping to Support Decision-Making after an Earthquake
It has long been recognized that earthquakes change the stress in the upper crust around the fault rupture and can influence the behaviour of neighbouring faults and volcanoes. Rapid estimates of these stress changes can provide the authorities managing the post-disaster situation with valuable data to identify and monitor potential threads and to update the estimates of seismic and volcanic hazard in a region. Here we propose a methodology to evaluate the potential influence of an earthquake on nearby faults and volcanoes and create easy-to-understand maps for decision-making support after large earthquakes. We apply this methodology to the Mw 7.8, 2016 Ecuador earthquake. Using Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) and continuous GPS data, we measure the coseismic ground deformation and estimate the distribution of slip over the fault rupture. We also build an alternative source model using the Global Centroid Moment Tensor (CMT) solution. Then we use these models to evaluate changes of static stress on the surrounding faults and volcanoes and produce maps of potentially activated faults and volcanoes. We found, in general, good agreement between our maps and the seismic and volcanic events that occurred after the Pedernales earthquake. We discuss the potential and limitations of the methodology.
- Open Access
- 29 December 2017
- Published by Walter de Gruyter GmbH in Open Geosciences
- Vol. 9 (1) , 719-734
Methodological approach for the estimation of a new velocity model for continental Ecuador
We used 33 stations belonging of the Ecuador Continuous Monitoring GNSS Network (REGME) during the period 2008-2014, with aim to contribute with a methodological approach for the estimation of a new velocity model for Continental Ecuador. We used daily solutions to perform the analysis of GNSS time series, to obtain models of the series that best fit, taking into count the trend, seasonal variations and the type of noise. The sum of all these components represent the real-time series, and thus we can have a better estimation of the velocity parameter and its uncertainty.The velocities were calculated introducing the trend, seasonality and noise that were presented in each series into the overall model, which improved uncertainty by 12% and changed in magnitude up to 1.7 mm/yr and 2.5 mm/yr in the horizontal and vertical components, respectively, with respect to the initial velocities. The velocity field describes the crustal movement of the REGME stations in mainland Ecuador with uncertainty of 1 mm/yr and 2 mm/yr for the horizontal and vertical components, respectively. Finally, a velocity model has been developed using the kriging technique whose geostatistical approach has been based on the data to identify the spatial characteristics by examining the observations by peers. The mean square error (rms) of prediction obtained in this method is 1.78 mm/yr and 1.95 mm/yr in the east and north components, respectivaly. The vertical component could not be modeled due to its chaotic behavior.
- 29 December 2017
- Published by Walter de Gruyter GmbH in Open Geosciences
- Vol. 9 (1) , 719-734
Open AccessMethodological approach for the estimation of a new velocity model for continental Ecuador
We used 33 stations belonging of the Ecuador Continuous Monitoring GNSS Network (REGME) during the period 2008-2014, with aim to contribute with a methodological approach for the estimation of a new velocity model for Continental Ecuador. We used daily solutions to perform the analysis of GNSS time series, to obtain models of the series that best fit, taking into count the trend, seasonal variations and the type of noise. The sum of all these components represent the real-time series, and thus we can have a better estimation of the velocity parameter and its uncertainty.The velocities were calculated introducing the trend, seasonality and noise that were presented in each series into the overall model, which improved uncertainty by 12% and changed in magnitude up to 1.7 mm/yr and 2.5 mm/yr in the horizontal and vertical components, respectively, with respect to the initial velocities. The velocity field describes the crustal movement of the REGME stations in mainland Ecuador with uncertainty of 1 mm/yr and 2 mm/yr for the horizontal and vertical components, respectively. Finally, a velocity model has been developed using the kriging technique whose geostatistical approach has been based on the data to identify the spatial characteristics by examining the observations by peers. The mean square error (rms) of prediction obtained in this method is 1.78 mm/yr and 1.95 mm/yr in the east and north components, respectivaly. The vertical component could not be modeled due to its chaotic behavior.
- 29 May 2017
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 15 (11) , 4719-4750
Urban modifiers of seismic vulnerability aimed at Urban Zoning Regulations
- 29 May 2017
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 15 (11) , 4719-4750
Urban modifiers of seismic vulnerability aimed at Urban Zoning Regulations