Lutfi Agartan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lutfi Agartan has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Emin Caglan Kumbur
Electrochemical Energy Systems Laboratory, Department of Mechanical Engineering, Drexel University, Philadelphia, PA 19104, USA
5 shared publications Bilen Akuzum
4 shared publications- Bilen Akuzum
Aepnus Technology, Inc
4 shared publications E. Caglan Kumbur
4 shared publicationsAbdullah Ozturk
3 shared publications- Jongee Park
Atilim University
3 shared publications
Latest Publications
- 1 September 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (9) , 090518
Two-Dimensional MXene Modified Electrodes for Improved Anodic Performance in Vanadium Redox Flow Batteries
In this work, Ti 3 C 2 T x MXene was investigated as electrocatalyst material for the anodic V 2+ /V 3+ reaction in vanadium redox flow batteries (VRFBs). A simple drop coating process was established using additive-free, aqueous MXene dispersions to fabricate MXene-coated carbon paper electrodes. The performance of Ti 3 C 2 T x as an anodic electrocatalyst was studied using cyclic voltammetry and electrochemical impedance spectroscopy in a three-electrode cell. Furthermore, flow battery testing was performed to determine the performance of the modified electrodes. At a current density of 50 mA cm −2 , the electrode with Ti 3 C 2 T x loading of 0.2 mg cm −2 enabled a 7% higher energy efficiency and 22% higher electrolyte utilization rate than the pristine electrode. At a higher current density (100 mA cm −2 ), the energy efficiency and electrolyte utilization were increased by 17% and 46%, respectively. At 50% SOC, the coated electrode was able to reach a limiting current density of 220 mA cm −2 while maintaining a voltaic efficiency above 80%, whereas the pristine electrode could only reach up to 160 mA cm −2 at the same voltaic efficiency. The improved performance was mainly attributed to the enhanced electrode kinetics, increased electrochemically active surface area, and improved wetting properties due to the addition of Ti 3 C 2 T x nanoflakes.
- 1 September 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (9) , 090518
Two-Dimensional MXene Modified Electrodes for Improved Anodic Performance in Vanadium Redox Flow Batteries
In this work, Ti 3 C 2 T x MXene was investigated as electrocatalyst material for the anodic V 2+ /V 3+ reaction in vanadium redox flow batteries (VRFBs). A simple drop coating process was established using additive-free, aqueous MXene dispersions to fabricate MXene-coated carbon paper electrodes. The performance of Ti 3 C 2 T x as an anodic electrocatalyst was studied using cyclic voltammetry and electrochemical impedance spectroscopy in a three-electrode cell. Furthermore, flow battery testing was performed to determine the performance of the modified electrodes. At a current density of 50 mA cm −2 , the electrode with Ti 3 C 2 T x loading of 0.2 mg cm −2 enabled a 7% higher energy efficiency and 22% higher electrolyte utilization rate than the pristine electrode. At a higher current density (100 mA cm −2 ), the energy efficiency and electrolyte utilization were increased by 17% and 46%, respectively. At 50% SOC, the coated electrode was able to reach a limiting current density of 220 mA cm −2 while maintaining a voltaic efficiency above 80%, whereas the pristine electrode could only reach up to 160 mA cm −2 at the same voltaic efficiency. The improved performance was mainly attributed to the enhanced electrode kinetics, increased electrochemically active surface area, and improved wetting properties due to the addition of Ti 3 C 2 T x nanoflakes.
- 13 July 2021
- Published by Drexel University Libraries
Electrosorption kinetics and salt removal performance of capacitive deionization systems
Capacitive deionization (CDI) is an emerging water desalination technology that offers unique advantages for energy efficient water desalination due to its design flexibility, long cycle life, low energy demand, reversible operation at low pressure and room temperature, simultaneous ion adsorption, and high coulombic efficiency. Despite their potential, a series of technical challenges hinder the widespread utilization of CDI systems. Among these, limited desalination performance has been identified as the key issue. This issue is primarily governed by the underutilization of electrodes, slow adsorption kinetics, and diminished energy efficiency of the system. Presently, the desalination performances of the CDI systems are limited by the lack of fundamental understanding of effects of operating conditions and electrode properties on the electrosorption kinetics. This PhD study seeks to address this critical issue by exploring fundamental mechanisms responsible for ion adsorption in electrodes. The overall objective of this dissertation is to establish a fundamental understanding of the effects of operating conditions and electrode properties on the desalination performances of the CDI systems by investigating the dependence of effective ion delivery on the composition and nanoscale morphology of the electrodes and flow directionality of the saline water. To achieve these goals, series of experiments were designed. Several materials and electrochemical characterization techniques were used to characterize electrode materials and study the effects of various operating conditions on the desalination performances of CDI systems. Using these experimental data, a fundamental understanding of the effects of electrode properties and operating conditions on the desalination kinetics and performance of the CDI systems has been obtained. Finally, this understanding was utilized to identify strategies for more effective delivery of ions, for improved utilization of the electrodes. Keywords: Activated Carbon Cloth, Capacitive Deionization, Electrosorption Kinetics, MXene, Salt Adsorption, Water Desalination
- 13 July 2021
- Published by Drexel University Libraries
Electrosorption kinetics and salt removal performance of capacitive deionization systems
Capacitive deionization (CDI) is an emerging water desalination technology that offers unique advantages for energy efficient water desalination due to its design flexibility, long cycle life, low energy demand, reversible operation at low pressure and room temperature, simultaneous ion adsorption, and high coulombic efficiency. Despite their potential, a series of technical challenges hinder the widespread utilization of CDI systems. Among these, limited desalination performance has been identified as the key issue. This issue is primarily governed by the underutilization of electrodes, slow adsorption kinetics, and diminished energy efficiency of the system. Presently, the desalination performances of the CDI systems are limited by the lack of fundamental understanding of effects of operating conditions and electrode properties on the electrosorption kinetics. This PhD study seeks to address this critical issue by exploring fundamental mechanisms responsible for ion adsorption in electrodes. The overall objective of this dissertation is to establish a fundamental understanding of the effects of operating conditions and electrode properties on the desalination performances of the CDI systems by investigating the dependence of effective ion delivery on the composition and nanoscale morphology of the electrodes and flow directionality of the saline water. To achieve these goals, series of experiments were designed. Several materials and electrochemical characterization techniques were used to characterize electrode materials and study the effects of various operating conditions on the desalination performances of CDI systems. Using these experimental data, a fundamental understanding of the effects of electrode properties and operating conditions on the desalination kinetics and performance of the CDI systems has been obtained. Finally, this understanding was utilized to identify strategies for more effective delivery of ions, for improved utilization of the electrodes. Keywords: Activated Carbon Cloth, Capacitive Deionization, Electrosorption Kinetics, MXene, Salt Adsorption, Water Desalination
- 13 February 2020
- Published by IWA Publishing in Journal of Water Supply: Research and Technology—AQUA
- Vol. 69 (2) , 134-144
Impact of flow configuration on electrosorption performance and energy consumption of CDI systems
The flow configuration selected for a capacitive deionization (CDI) system can impact the desalination performance due to drastic changes to the ion transport. Herein, a zero-gap CDI cell fixture with various flow configurations was utilized to investigate the effects of flow directionality on the CDI performance of activated carbon cloth (ACC) electrodes. Salt adsorption capacities and salt adsorption rates were determined for three commonly studied flow field designs (parallel (PFF), interdigitated (IDFF), and serpentine (SFF)) at various flow rates (2–128 mL/min). Increasing the flow rate was found to result in decreasing CDI performance for SFF and IDFF designs. On the other hand, the peak performance was observed for the parallel flow field at 32 mL/min flow rate. Additionally, the pressure drop values for different flow configurations were measured, and the energy consumptions were calculated. Overall, the findings showed that the performance of CDI systems strongly depends on the selected flow field geometry. Among the tested flow fields, the parallel configuration offered the best balance between CDI performance and energy efficiency. However, the designs that exert high hydrodynamic forces on the electrode plane showed poor performance due to rip-off of ions from the double layer causing a significant capacity loss for ACC electrodes.
- 13 February 2020
- Published by IWA Publishing in Journal of Water Supply: Research and Technology—AQUA
- Vol. 69 (2) , 134-144
Impact of flow configuration on electrosorption performance and energy consumption of CDI systems
The flow configuration selected for a capacitive deionization (CDI) system can impact the desalination performance due to drastic changes to the ion transport. Herein, a zero-gap CDI cell fixture with various flow configurations was utilized to investigate the effects of flow directionality on the CDI performance of activated carbon cloth (ACC) electrodes. Salt adsorption capacities and salt adsorption rates were determined for three commonly studied flow field designs (parallel (PFF), interdigitated (IDFF), and serpentine (SFF)) at various flow rates (2–128 mL/min). Increasing the flow rate was found to result in decreasing CDI performance for SFF and IDFF designs. On the other hand, the peak performance was observed for the parallel flow field at 32 mL/min flow rate. Additionally, the pressure drop values for different flow configurations were measured, and the energy consumptions were calculated. Overall, the findings showed that the performance of CDI systems strongly depends on the selected flow field geometry. Among the tested flow fields, the parallel configuration offered the best balance between CDI performance and energy efficiency. However, the designs that exert high hydrodynamic forces on the electrode plane showed poor performance due to rip-off of ions from the double layer causing a significant capacity loss for ACC electrodes.
- 10 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (5) , 5866-5875
Percolation Characteristics of Conductive Additives for Capacitive Flowable (Semi-Solid) Electrodes
Understanding the percolation characteristics of multi-component conducting suspensions is critical for the development of flowable (semi-solid) electrochemical systems for energy storage and capacitive deionization with optimal electrochemical and rheological performance. Despite its significance, not much is known about the impact of the selected particle morphology on the agglomeration kinetics and the state of dispersion in flowable electrodes. In this study, impact of the conductive additive morphology on the electrochemical and rheological response of capacitive flowable electrodes has been systematically investigated. Critical viscosity limits have been determined for common carbon additives that offer slurry formulations with improved electrochemical and rheological performance. For instance, at the same electrical conductivity of 60 mS cm-1, higher aspect ratio particles, such as graphene and carbon nanotubes, offered 4- and 2.4-times lower viscosity compared to carbon black due to the improved packing and conformity of the high-aspect-ratio particles. On the other hand, thixotropic measurements showed that the flowable electrodes with carbon black exhibit the fastest agglomeration kinetics, offering 25 % less time to recover from the applied shear due to spherical morphology and facile agglomeration kinetics. Overall, our findings show that the particle morphology has a significant impact on the electrochemical and rheological performance of flowable electrodes with up to 40 % difference in capacitance for similar viscosity electrodes. Furthermore, a direct correlation between the rheological and the electrochemical properties was established, offering morphology-independent practical guidelines for formulating slurries with optimal performance. In this manner, particles that can achieve the highest density of packing prior to the critical limit were found to offer the optimal balance between electrochemical and rheological performance.
- 10 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (5) , 5866-5875
Percolation Characteristics of Conductive Additives for Capacitive Flowable (Semi-Solid) Electrodes
Understanding the percolation characteristics of multi-component conducting suspensions is critical for the development of flowable (semi-solid) electrochemical systems for energy storage and capacitive deionization with optimal electrochemical and rheological performance. Despite its significance, not much is known about the impact of the selected particle morphology on the agglomeration kinetics and the state of dispersion in flowable electrodes. In this study, impact of the conductive additive morphology on the electrochemical and rheological response of capacitive flowable electrodes has been systematically investigated. Critical viscosity limits have been determined for common carbon additives that offer slurry formulations with improved electrochemical and rheological performance. For instance, at the same electrical conductivity of 60 mS cm-1, higher aspect ratio particles, such as graphene and carbon nanotubes, offered 4- and 2.4-times lower viscosity compared to carbon black due to the improved packing and conformity of the high-aspect-ratio particles. On the other hand, thixotropic measurements showed that the flowable electrodes with carbon black exhibit the fastest agglomeration kinetics, offering 25 % less time to recover from the applied shear due to spherical morphology and facile agglomeration kinetics. Overall, our findings show that the particle morphology has a significant impact on the electrochemical and rheological performance of flowable electrodes with up to 40 % difference in capacitance for similar viscosity electrodes. Furthermore, a direct correlation between the rheological and the electrochemical properties was established, offering morphology-independent practical guidelines for formulating slurries with optimal performance. In this manner, particles that can achieve the highest density of packing prior to the critical limit were found to offer the optimal balance between electrochemical and rheological performance.
- 1 February 2019
- Published by Elsevier in Desalination
- Vol. 452, 1-8
Influence of operating conditions and cathode parameters on desalination performance of hybrid CDI systems
- 1 February 2019
- Published by Elsevier in Desalination
- Vol. 452, 1-8
Influence of operating conditions and cathode parameters on desalination performance of hybrid CDI systems
- 11 August 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (11) , A2519-A2527
Reticulated Carbon Electrodes for Improved Charge Transport in Electrochemical Flow Capacitors
In this study, we report on an approach to flow cell design that can enable a significantly improved power output (∼10x) for electrochemical flow capacitors (EFCs), even at large flow channel gaps. Reticulated vitreous carbon (RVC) electrodes of various average pore sizes (0.43–2 mm) were integrated into EFC flow cell fixtures with channel gaps of 5 mm. Electrochemical testing under flow conditions showed a 10-fold improvement in the power density with the RVC integration (290 W/m2, 580 W/kg) for the same slurry composition. This improvement was mostly attributed to the presence of a 3D porous electrode insert (i.e., RVC) that shortened the travel distance of the electrons to the current collectors. Pressure drop in the RVC containing cells was also investigated and found to increase up to 30% depending on the pore size. However, this increase was found to be offset by the increase in the channel depth, yielding almost no change in pressure as compared to conventional narrow-gap (>0.75 mm) flow channels. RVCs having an average pore size of 0.55 mm showed the best performance out of all studied cases with improved coulombic efficiency and good specific capacity (85 F/g) under flowing conditions.
- 11 August 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (11) , A2519-A2527
Reticulated Carbon Electrodes for Improved Charge Transport in Electrochemical Flow Capacitors
In this study, we report on an approach to flow cell design that can enable a significantly improved power output (∼10x) for electrochemical flow capacitors (EFCs), even at large flow channel gaps. Reticulated vitreous carbon (RVC) electrodes of various average pore sizes (0.43–2 mm) were integrated into EFC flow cell fixtures with channel gaps of 5 mm. Electrochemical testing under flow conditions showed a 10-fold improvement in the power density with the RVC integration (290 W/m2, 580 W/kg) for the same slurry composition. This improvement was mostly attributed to the presence of a 3D porous electrode insert (i.e., RVC) that shortened the travel distance of the electrons to the current collectors. Pressure drop in the RVC containing cells was also investigated and found to increase up to 30% depending on the pore size. However, this increase was found to be offset by the increase in the channel depth, yielding almost no change in pressure as compared to conventional narrow-gap (>0.75 mm) flow channels. RVCs having an average pore size of 0.55 mm showed the best performance out of all studied cases with improved coulombic efficiency and good specific capacity (85 F/g) under flowing conditions.
- 1 August 2018
- Published by Elsevier in Separation and Purification Technology
- Vol. 202, 67-75
Influence of thermal treatment conditions on capacitive deionization performance and charge efficiency of carbon electrodes
- 1 August 2018
- Published by Elsevier in Separation and Purification Technology
- Vol. 202, 67-75
Influence of thermal treatment conditions on capacitive deionization performance and charge efficiency of carbon electrodes
- 7 February 2017
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 47 (3) , 369-380
Effects of particle dispersion and slurry preparation protocol on electrochemical performance of capacitive flowable electrodes
- 7 February 2017
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 47 (3) , 369-380
Effects of particle dispersion and slurry preparation protocol on electrochemical performance of capacitive flowable electrodes
- 1 December 2015
- Published by Elsevier in Ceramics International
- Vol. 41 (10) , 12788-12797
Effect of initial water content and calcination temperature on photocatalytic properties of TiO2 nanopowders synthesized by the sol–gel process
- 1 December 2015
- Published by Elsevier in Ceramics International
- Vol. 41 (10) , 12788-12797
Effect of initial water content and calcination temperature on photocatalytic properties of TiO2 nanopowders synthesized by the sol–gel process