Valentin Richter-Trummer
Valentin Richter-Trummer has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Paulo Manuel Salgado Tavares de Castro
Faculdade de Engenharia, Universidade do Porto, rua Dr. Roberto Frias, 4200-465 Porto, Portugal
17 shared publications - Pedro Miguel Guimarães Pires Moreira
Faculdade de Engenharia, Universidade do Porto, 4200-465 Porto, Portugal
10 shared publications - Sergio M. O. Tavares
TEMA—Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, 3810-193 Aveiro, Portugal
6 shared publications - Pedro Vilaça
Department of Energy and Mechanical Engineering, School of Engineering, Aalto University, 02150 Espoo, Finland
4 shared publications - Miguel A. V. de Figueiredo
FEUP— Faculty of Engineering, University of Porto, 4150-564 Porto, Portugal
3 shared publications - Antje Ahrens
Fraunhofer Institute for Machine Tools and Forming Technology IWU, Reichenhainer Str. 88, 09126 Chemnitz, Germany
2 shared publications
Latest Publications
- 19 March 2023
- Published by Springer Nature
- p. 173-188
Assisted Facility Layout Planning for Sustainable Automotive Assembly
- 19 March 2023
- Published by Springer Nature
- p. 173-188
Assisted Facility Layout Planning for Sustainable Automotive Assembly
- Open Access
Virtual Sensor-Based Geometry Prediction of Complex Sheet Metal Parts Formed by Robotic Rollforming
Sheet metal parts can often replace milled components, strongly improving the buy-to-fly ratio in the aeronautical sector. However, the sheet metal forming of complex parts traditionally requires expensive tooling, which is usually prohibitive for low manufacturing rates. To achieve precise parts, non-productive and cost-intensive geometry straightening processes are additionally often required after forming. Rollforming is a possible technology for producing profiles at large rates. For low manufacturing rates, robotic rollforming can be an interesting option, significantly reducing investment at the cost of higher manufacturing times while keeping a high process flexibility. Forming is performed incrementally by a single roller set moved by the robot along predefined bending curves. The present work’s contribution to the overall solution is the development of an intelligent algorithm to calculate geometry after a robotic rollforming process based on process reaction forces. This information is required for in-process geometric distortion correction. Reaction forces and torques are acquired during the process, and geometry is calculated based on artificial intelligence (AI) applied to that information. The present paper describes the AI development for this virtual geometry sensing system.
Open AccessVirtual Sensor-Based Geometry Prediction of Complex Sheet Metal Parts Formed by Robotic Rollforming
Sheet metal parts can often replace milled components, strongly improving the buy-to-fly ratio in the aeronautical sector. However, the sheet metal forming of complex parts traditionally requires expensive tooling, which is usually prohibitive for low manufacturing rates. To achieve precise parts, non-productive and cost-intensive geometry straightening processes are additionally often required after forming. Rollforming is a possible technology for producing profiles at large rates. For low manufacturing rates, robotic rollforming can be an interesting option, significantly reducing investment at the cost of higher manufacturing times while keeping a high process flexibility. Forming is performed incrementally by a single roller set moved by the robot along predefined bending curves. The present work’s contribution to the overall solution is the development of an intelligent algorithm to calculate geometry after a robotic rollforming process based on process reaction forces. This information is required for in-process geometric distortion correction. Reaction forces and torques are acquired during the process, and geometry is calculated based on artificial intelligence (AI) applied to that information. The present paper describes the AI development for this virtual geometry sensing system.
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 1788-1793
The Influence of Gaps and Misalignment on Friction Stir Welded Butt Joints of Medium-Sized Parts
In order to industrialize friction stir welding (FSW) processes, not only the machine concept itself needs to be evaluated, but also the robustness of the process application being carried out on the machine. Especially for FSW of medium-sized and larger parts, a small degree of misalignment can have an increasing influence on the weld quality. Therefore an exemplary tolerance study for friction stir welded butt joints was conducted. The intentional introduction of gaps between the sheets to be welded can limit the welding process and thus the weld quality. However, for the considered experimental set-up it can be shown that the introduction of a well-defined gap can support the welding process and weld quality. The experimental procedure was carried out on a parallel kinematic machine - a so-called Pentapod. This machine is suitable for large and complex three-dimensional structures. Although the machine is able to record the process forces (Fx, Fy and Fz) acting on the tool–work piece interface, the forces acting perpendicular to the clamping system are still unknown. Therefore additional load cells were integrated into the clamping system to measure the in-process reaction forces. The combined results of the force measurements give a nearly complete overview of the internal loads during the process. In conjunction with knowledge about gaps and misalignment, the data gained in this study can help to understand and predict the clamping behaviour, and thus design rules for future clamping systems can be derived.
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 1788-1793
The Influence of Gaps and Misalignment on Friction Stir Welded Butt Joints of Medium-Sized Parts
In order to industrialize friction stir welding (FSW) processes, not only the machine concept itself needs to be evaluated, but also the robustness of the process application being carried out on the machine. Especially for FSW of medium-sized and larger parts, a small degree of misalignment can have an increasing influence on the weld quality. Therefore an exemplary tolerance study for friction stir welded butt joints was conducted. The intentional introduction of gaps between the sheets to be welded can limit the welding process and thus the weld quality. However, for the considered experimental set-up it can be shown that the introduction of a well-defined gap can support the welding process and weld quality. The experimental procedure was carried out on a parallel kinematic machine - a so-called Pentapod. This machine is suitable for large and complex three-dimensional structures. Although the machine is able to record the process forces (Fx, Fy and Fz) acting on the tool–work piece interface, the forces acting perpendicular to the clamping system are still unknown. Therefore additional load cells were integrated into the clamping system to measure the in-process reaction forces. The combined results of the force measurements give a nearly complete overview of the internal loads during the process. In conjunction with knowledge about gaps and misalignment, the data gained in this study can help to understand and predict the clamping behaviour, and thus design rules for future clamping systems can be derived.
- 1 December 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (12) , 2323-2328
Assessment of residual stress of welded structural steel plates with or without post weld rolling using the contour method and neutron diffraction
- 1 December 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (12) , 2323-2328
Assessment of residual stress of welded structural steel plates with or without post weld rolling using the contour method and neutron diffraction
- 28 February 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 68 (9-12) , 2271-2281
Methodology for prediction of distortion of workpieces manufactured by high speed machining based on an accurate through-the-thickness residual stress determination
- 28 February 2013
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 68 (9-12) , 2271-2281
Methodology for prediction of distortion of workpieces manufactured by high speed machining based on an accurate through-the-thickness residual stress determination
- 12 November 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 730-732, 793-798
Fatigue Crack Striation Spacing for Welded and Base Material CT Steel Specimens
Scanning electron microscopy (SEM) observation of the fracture surface of CT specimens was carried out at CEMUP in the context of a FEUP R&D programme for the characterization of fatigue crack growth (FCG) of base material and welded steel CT specimens, carried out under constant load range, reported in a companion paper. The inclusion of specimens of welded material in the FCG characterization programme justified the need for relatively large size specimens. The thickness of the specimens (B=32mm) was approximately identical to the thickness of the structural application of interest, since with thinner specimens the possible effects of residual stress fields would be at least partially lost. The CT specimens were designed according to ASTM E647 standard. The FEI QUANTA 400 FEG / EDAX Pegasus X4M available at CEMUP was used for the SEM observations, carried out in the fatigue fracture surfaces of base and welded (HAZ) steel. Both in base material as well as in welded specimens, it was found that there are regions of the fracture surfaces where no striations are observed, mixed with other regions (patches) with striations. Some regions are featureless (ropey appearance). It was not possible to find a preferential orientation of the striation spacing, that might be directly related with the macroscopic direction of crack propagation; on the contrary, the regions presenting striations seem to have a mainly random orientation. This fact contributes to the absence of correlation between the distance between striations (s) measured using SEM, and the macroscopic fatigue crack growth rate da/dN. Only for substantial values of the crack length/specimen width (a/W) ratio a reasonable agreement between s and da/dN is found. The relationship s/(da/dN) presents values that decrease up to approximately one, as a/W increases. For low values of a/W, s is one or two orders of magnitude greater than da/dN. In the specimens analyzed, fatigue crack growth rates below approximately 2 to 3 x10‑7 m/cycle are associated with approximately constant s values. This border is over the transition between regions I and II of the typical sigmoidal log-log plot of the da/dN vs. DK (I corresponding to the near threshold regime and II to the Paris law regime), and this fact should be accounted for in failure analysis involving SEM of fracture surfaces. Finally, the distance between striations s proved to be insensitive to the presence of important residual stresses in the case of the welded specimens.
- 12 November 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 730-732, 793-798
Fatigue Crack Striation Spacing for Welded and Base Material CT Steel Specimens
Scanning electron microscopy (SEM) observation of the fracture surface of CT specimens was carried out at CEMUP in the context of a FEUP R&D programme for the characterization of fatigue crack growth (FCG) of base material and welded steel CT specimens, carried out under constant load range, reported in a companion paper. The inclusion of specimens of welded material in the FCG characterization programme justified the need for relatively large size specimens. The thickness of the specimens (B=32mm) was approximately identical to the thickness of the structural application of interest, since with thinner specimens the possible effects of residual stress fields would be at least partially lost. The CT specimens were designed according to ASTM E647 standard. The FEI QUANTA 400 FEG / EDAX Pegasus X4M available at CEMUP was used for the SEM observations, carried out in the fatigue fracture surfaces of base and welded (HAZ) steel. Both in base material as well as in welded specimens, it was found that there are regions of the fracture surfaces where no striations are observed, mixed with other regions (patches) with striations. Some regions are featureless (ropey appearance). It was not possible to find a preferential orientation of the striation spacing, that might be directly related with the macroscopic direction of crack propagation; on the contrary, the regions presenting striations seem to have a mainly random orientation. This fact contributes to the absence of correlation between the distance between striations (s) measured using SEM, and the macroscopic fatigue crack growth rate da/dN. Only for substantial values of the crack length/specimen width (a/W) ratio a reasonable agreement between s and da/dN is found. The relationship s/(da/dN) presents values that decrease up to approximately one, as a/W increases. For low values of a/W, s is one or two orders of magnitude greater than da/dN. In the specimens analyzed, fatigue crack growth rates below approximately 2 to 3 x10‑7 m/cycle are associated with approximately constant s values. This border is over the transition between regions I and II of the typical sigmoidal log-log plot of the da/dN vs. DK (I corresponding to the near threshold regime and II to the Paris law regime), and this fact should be accounted for in failure analysis involving SEM of fracture surfaces. Finally, the distance between striations s proved to be insensitive to the presence of important residual stresses in the case of the welded specimens.
- 12 November 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 730-732, 787-792
Fatigue Crack Propagation Behavior of the Welded Steel of a Railway Bridge
In the context of a R&D project concerning the new Alcácer do Sal composite railway bridge, a study of the fatigue crack growth on samples of its base material and weldments was performed. For this purpose, tests were carried out on CT specimens designed according to ASTM E647 standard, using the approximate thickness (B) of a structural detail of interest, B=32mm. The choice of B led to a relatively large specimen and was justified by the desire to better simulate service conditions, which would not be possible with smaller specimens, particularly in the case of weldments. The test matrix used included three values of R ratio (maximum/minimum load), 0.1, 0.4 and 0.7, and three material conditions, namely base material (BM), heat affected zone (HAZ) and weld metal (WM). When the nominal range of the stress intensity factor (DK) is used, the measured data displays a strong effect of the weldments on the FCG rates, with the base material presenting higher da/dN values. An evaluation of opening load behaviour was carried out, and it showed extensive closure caused by residual stresses in the HAZ and WM specimens. The investigation included the full field measurement of the residual stress perpendicular to the crack plane, using the contour technique. When the opening load effect was taken into consideration it was found that the da/dN vs. ∆K of the BM, HAZ and WM specimens is approximately identical. Furthermore if loading effects are considered, no significant difference is found for the three R values used, even if, as expected, higher R corresponds to higher da/dN values.
- 12 November 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 730-732, 787-792
Fatigue Crack Propagation Behavior of the Welded Steel of a Railway Bridge
In the context of a R&D project concerning the new Alcácer do Sal composite railway bridge, a study of the fatigue crack growth on samples of its base material and weldments was performed. For this purpose, tests were carried out on CT specimens designed according to ASTM E647 standard, using the approximate thickness (B) of a structural detail of interest, B=32mm. The choice of B led to a relatively large specimen and was justified by the desire to better simulate service conditions, which would not be possible with smaller specimens, particularly in the case of weldments. The test matrix used included three values of R ratio (maximum/minimum load), 0.1, 0.4 and 0.7, and three material conditions, namely base material (BM), heat affected zone (HAZ) and weld metal (WM). When the nominal range of the stress intensity factor (DK) is used, the measured data displays a strong effect of the weldments on the FCG rates, with the base material presenting higher da/dN values. An evaluation of opening load behaviour was carried out, and it showed extensive closure caused by residual stresses in the HAZ and WM specimens. The investigation included the full field measurement of the residual stress perpendicular to the crack plane, using the contour technique. When the opening load effect was taken into consideration it was found that the da/dN vs. ∆K of the BM, HAZ and WM specimens is approximately identical. Furthermore if loading effects are considered, no significant difference is found for the three R values used, even if, as expected, higher R corresponds to higher da/dN values.
- 25 May 2012
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 3 (2) , 184-203
Fatigue crack propagation behaviour in thick steel weldments
Fatigue crack propagation behaviour in thick steel weldments
- 25 May 2012
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 3 (2) , 184-203
Fatigue crack propagation behaviour in thick steel weldments
Fatigue crack propagation behaviour in thick steel weldments
- 1 March 2012
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 538, 81-88
Influence of the FSW clamping force on the final distortion and residual stress field
- 1 March 2012
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 538, 81-88
Influence of the FSW clamping force on the final distortion and residual stress field
- 3 May 2011
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 42 (5) , 452-459
Analysis of crack growth behavior in a double cantilever beam adhesive fracture test by different digital image processing techniques
Double cantilever beam (DCB) tests are common experiments in the field of adhesive fracture mechanics. During such an experiment, both the load and the crack length have to be monitored. Digital image processing techniques offer interesting possibilities in various fields of science. Automated analyses may significantly reduce the necessary manpower for certain cumbersome tasks. The analysis of large series of images may be done in less time, since automated image processing techniques are able to work efficiently and with constant quality 24 h per day. In this work, a series of images obtained by a high‐speed camera is analyzed in order to determine the crack growth behavior during a DCB test. The present work represents a contribution to the effort of automating the crack growth measurement, by proposing and comparing different automated techniques.
- 3 May 2011
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 42 (5) , 452-459
Analysis of crack growth behavior in a double cantilever beam adhesive fracture test by different digital image processing techniques
Double cantilever beam (DCB) tests are common experiments in the field of adhesive fracture mechanics. During such an experiment, both the load and the crack length have to be monitored. Digital image processing techniques offer interesting possibilities in various fields of science. Automated analyses may significantly reduce the necessary manpower for certain cumbersome tasks. The analysis of large series of images may be done in less time, since automated image processing techniques are able to work efficiently and with constant quality 24 h per day. In this work, a series of images obtained by a high‐speed camera is analyzed in order to determine the crack growth behavior during a DCB test. The present work represents a contribution to the effort of automating the crack growth measurement, by proposing and comparing different automated techniques.