Witold Chrominski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Witold Chrominski has a total of 206 co-authors. Here are the top co-authors by number of shared publications:
- Małgorzata Lewandowska
Faculty of Materials Science and Engineering, Warsaw University of Technology, Warsaw, Poland
18 shared publications - Lukasz Kurpaska
National Centre for Nuclear Research
8 shared publications - Mariusz Kulczyk
Institute of High Pressure Physics, Polish Academy of Sciences (Unipress), Sokołowska 29, 01-142 Warsaw, Poland
7 shared publications - Damian Kalita
Polish Academy of Sciences
6 shared publications - Bogusława Adamczyk-Cieślak
Faculty of Materials Science and Engineering, Warsaw University of Technology, 02-507 Warsaw, Poland
5 shared publications - Lech Olejnik
Warsaw University of Technology
5 shared publications
Latest Publications
- Open Access
- 23 October 2026
- Published by Elsevier in Acta Materialia
- Vol. 322
The effects of short-range order and secondary phases on the thermal properties of a CoCrFeNi multiprincipal element alloy
- 23 October 2026
- Published by Elsevier in Acta Materialia
- Vol. 322
Open AccessThe effects of short-range order and secondary phases on the thermal properties of a CoCrFeNi multiprincipal element alloy
- Open Access
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 825-836
Microstructural Characterization of the Effect of Minor and Severe Plastic Deformation on Martensite Decomposition in Ti-6Al-4V Alloy
Martensite decomposition in titanium alloys is the phase transformation most commonly associated with their standard heat treatment – hardening and tempering. However, it also occurs during other manufacturing processes, such as thermomechanical processing and additive manufacturing. Understanding the nature of the martensite decomposition process enhances the ability to control it. Unlike previous studies in this field, which were based on light microscopy (LM) and scanning electron microscopy (SEM) analysis, this study examined the effect of plastic deformation of martensite on its decomposition using transmission electron microscopy (TEM) and EBSD/TKD methods. In addition, a variant of hydrostatic extrusion of the quenched Ti-6Al-4V alloy was also considered.
- 18 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 71 (3) , 825-836
Open AccessMicrostructural Characterization of the Effect of Minor and Severe Plastic Deformation on Martensite Decomposition in Ti-6Al-4V Alloy
Martensite decomposition in titanium alloys is the phase transformation most commonly associated with their standard heat treatment – hardening and tempering. However, it also occurs during other manufacturing processes, such as thermomechanical processing and additive manufacturing. Understanding the nature of the martensite decomposition process enhances the ability to control it. Unlike previous studies in this field, which were based on light microscopy (LM) and scanning electron microscopy (SEM) analysis, this study examined the effect of plastic deformation of martensite on its decomposition using transmission electron microscopy (TEM) and EBSD/TKD methods. In addition, a variant of hydrostatic extrusion of the quenched Ti-6Al-4V alloy was also considered.
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Irradiation Temperature Governs the Transition in Plastic Initiation From Nucleation to Defect-controlled Behaviour in Fe-9Cr-NiSiP
Ion irradiation modifies the nanoscale initiation of plasticity in ferritic Fe-Cr alloys through the formation and evolution of irradiation-induced defects. Here, the deformation behaviour of a Fe-9Cr-NiSiP model alloy irradiated to 5 dpa at room temperature and 300°C is examined. Nanoindentation reveals systematic changes in pop-in behaviour, indicating a transition from nucleation-controlled plastic initiation in the pristine material to defect-controlled deformation after irradiation. Room-temperature irradiation produces a high density of fine defect structures that promote heterogeneous dislocation nucleation while restricting dislocation motion. In contrast, irradiation at 300°C leads to defect coarsening and solute segregation of Cr, Ni, Si and P, forming more stable defect complexes that delay plastic initiation. Correlative microscopy reveals distinct subsurface deformation morphologies consistent with the mechanical response. These results show that irradiation temperature controls defect evolution, which in turn governs the nanoscale onset of plasticity in Fe-Cr alloys.
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIrradiation Temperature Governs the Transition in Plastic Initiation From Nucleation to Defect-controlled Behaviour in Fe-9Cr-NiSiP
Ion irradiation modifies the nanoscale initiation of plasticity in ferritic Fe-Cr alloys through the formation and evolution of irradiation-induced defects. Here, the deformation behaviour of a Fe-9Cr-NiSiP model alloy irradiated to 5 dpa at room temperature and 300°C is examined. Nanoindentation reveals systematic changes in pop-in behaviour, indicating a transition from nucleation-controlled plastic initiation in the pristine material to defect-controlled deformation after irradiation. Room-temperature irradiation produces a high density of fine defect structures that promote heterogeneous dislocation nucleation while restricting dislocation motion. In contrast, irradiation at 300°C leads to defect coarsening and solute segregation of Cr, Ni, Si and P, forming more stable defect complexes that delay plastic initiation. Correlative microscopy reveals distinct subsurface deformation morphologies consistent with the mechanical response. These results show that irradiation temperature controls defect evolution, which in turn governs the nanoscale onset of plasticity in Fe-Cr alloys.
- Open Access
- 22 April 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Dislocation density evolution in Eurofer97: Nanoindentation study supported by FEM and STEM
- 22 April 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Open AccessDislocation density evolution in Eurofer97: Nanoindentation study supported by FEM and STEM
- 28 March 2026
- Published by Elsevier in Acta Materialia
- Vol. 311
Local chemical ordering and its effects on the ageing phenomena in AlMgSi alloy with Ag additions
- 28 March 2026
- Published by Elsevier in Acta Materialia
- Vol. 311
Local chemical ordering and its effects on the ageing phenomena in AlMgSi alloy with Ag additions
- 19 March 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 627
Growth of deuterium supersaturated surface layer with increasing ion flux and fluence in plasma-exposed tungsten
- 19 March 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 627
Growth of deuterium supersaturated surface layer with increasing ion flux and fluence in plasma-exposed tungsten
- 22 November 2025
- Published by Elsevier in Acta Materialia
- Vol. 304
Effect of Ag on the precipitation stability in Al-Mg-Si-Ag alloy: First-principles calculations, Calphad modeling and experimental validation
- 22 November 2025
- Published by Elsevier in Acta Materialia
- Vol. 304
Effect of Ag on the precipitation stability in Al-Mg-Si-Ag alloy: First-principles calculations, Calphad modeling and experimental validation
- Open Access
- 25 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 2652-2666
The impact of microstructure refinement and passive layers formation on the antibacterial activity of lead-free brass
- 25 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 2652-2666
Open AccessThe impact of microstructure refinement and passive layers formation on the antibacterial activity of lead-free brass
- Open Access
- 13 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 15-25
Annealing-induced precipitation strengthening and thermal stability of an ultrafine-grained bioresorbable Zn–Li–Mn–Mg alloy processed by rapid solidification
- 13 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 15-25
Open AccessAnnealing-induced precipitation strengthening and thermal stability of an ultrafine-grained bioresorbable Zn–Li–Mn–Mg alloy processed by rapid solidification