Linsong Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Linsong Wu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Xiaojie Li
7 shared publicationsXiaohong Wang
6 shared publicationsHonghao Yan
5 shared publications- Honghao Yan
School of Mechanics and Aerospace Engineering, State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, Dalian University of Technology , Dalian 116024, China
2 shared publications Tiejun Zhao
2 shared publications- Chenglong Zhuang
Department of Civil Engineering, Yangtze University, Jingzhou 434000, China
1 shared publication
Latest Publications
- Open Access
- 12 July 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (29) , 31455-31463
Characterization and Mechanism Elucidation of Nano-TiO2 Composites Prepared by Gaseous Detonation Method
In this study, a series of nano-TiO2 composite materials, including nano-TiO2, nano-SnO2/TiO2, nano-SiO2/TiO2, and nano-Fe2O3/TiO2, were successfully synthesized via the gaseous detonation method. Comprehensive characterization of the synthesized samples was carried out through X-ray diffraction (XRD), transmission electron microscopy/high-resolution TEM (TEM/HRTEM), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), Brunauer-Emmett-Teller (BET) method, and Fourier transform infrared (FTIR) analysis, which unveiled the significant influence of precursor types on the microstructure of the composite materials. Specifically, the incorporation of Sn4+ promoted the transformation of TiO2 to the rutile phase, reducing particle sizes from 25 to 19 nm and increasing the specific surface area from 44 to 86 m2/g. In contrast, the introduction of SiO2 impeded the rutile phase formation, leading to a marked reduction in particle size to 14 nm and an enhancement of the specific surface area to 104 m2/g. Furthermore, the presence of Fe3+ promoted the formation of the rutile phase and enabled particle growth to 44 nm. These findings not only deepen the understanding of structural control in the synthesis of nano-TiO2 composite materials via the gaseous detonation method but also highlight the critical role of precursor selection in determining the properties of the resulting materials.
- 12 July 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (29) , 31455-31463
Open AccessCharacterization and Mechanism Elucidation of Nano-TiO2 Composites Prepared by Gaseous Detonation Method
In this study, a series of nano-TiO2 composite materials, including nano-TiO2, nano-SnO2/TiO2, nano-SiO2/TiO2, and nano-Fe2O3/TiO2, were successfully synthesized via the gaseous detonation method. Comprehensive characterization of the synthesized samples was carried out through X-ray diffraction (XRD), transmission electron microscopy/high-resolution TEM (TEM/HRTEM), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), Brunauer-Emmett-Teller (BET) method, and Fourier transform infrared (FTIR) analysis, which unveiled the significant influence of precursor types on the microstructure of the composite materials. Specifically, the incorporation of Sn4+ promoted the transformation of TiO2 to the rutile phase, reducing particle sizes from 25 to 19 nm and increasing the specific surface area from 44 to 86 m2/g. In contrast, the introduction of SiO2 impeded the rutile phase formation, leading to a marked reduction in particle size to 14 nm and an enhancement of the specific surface area to 104 m2/g. Furthermore, the presence of Fe3+ promoted the formation of the rutile phase and enabled particle growth to 44 nm. These findings not only deepen the understanding of structural control in the synthesis of nano-TiO2 composite materials via the gaseous detonation method but also highlight the critical role of precursor selection in determining the properties of the resulting materials.
- Open Access
Study on Photocatalytic Performance of Ag/TiO2 Modified Cement Mortar
In this paper, Ag-TiO2 photocatalysts with different Ag contents (1 mol%–5 mol%) were prepared and applied to cement mortar. The photocatalytic performance of Ag-TiO2 and photocatalytic cement mortar under UV light and simulated solar light was evaluated. The results showed that Ag loading on the surface of TiO2 could reduce its band gap width and increase its absorbance in the visible region, and 2% Ag-TiO2 had the highest photocatalytic activity under UV light, the degradation rate of methyl orange (MO) was 95.5% at 30 min, and the first-order reaction constant k was 0.0980 min−1, which was 61.7% higher than that of TiO2, and 5% Ag-TiO2 had the highest photocatalytic activity under solar light, the degradation rate of methylene blue (MB) was 69.8% at 40 min, and the first-order reaction constant k was 0.0294 min−1, which was 90.9% higher than that of TiO2. The photocatalytic mortar prepared by the spraying method has high photocatalytic performance, The MO degradation rate of sample S2 under UV light was 87.5% after 120 min, MB degradation rate of sample S5 under solar light was 75.4% after 120 min. The photocatalytic reaction conforms to the zero-order reaction kinetics, which was 1.5 times–3.3 times higher than that of the mixed samples and has no effect on the mechanical properties of mortar.
Open AccessStudy on Photocatalytic Performance of Ag/TiO2 Modified Cement Mortar
In this paper, Ag-TiO2 photocatalysts with different Ag contents (1 mol%–5 mol%) were prepared and applied to cement mortar. The photocatalytic performance of Ag-TiO2 and photocatalytic cement mortar under UV light and simulated solar light was evaluated. The results showed that Ag loading on the surface of TiO2 could reduce its band gap width and increase its absorbance in the visible region, and 2% Ag-TiO2 had the highest photocatalytic activity under UV light, the degradation rate of methyl orange (MO) was 95.5% at 30 min, and the first-order reaction constant k was 0.0980 min−1, which was 61.7% higher than that of TiO2, and 5% Ag-TiO2 had the highest photocatalytic activity under solar light, the degradation rate of methylene blue (MB) was 69.8% at 40 min, and the first-order reaction constant k was 0.0294 min−1, which was 90.9% higher than that of TiO2. The photocatalytic mortar prepared by the spraying method has high photocatalytic performance, The MO degradation rate of sample S2 under UV light was 87.5% after 120 min, MB degradation rate of sample S5 under solar light was 75.4% after 120 min. The photocatalytic reaction conforms to the zero-order reaction kinetics, which was 1.5 times–3.3 times higher than that of the mixed samples and has no effect on the mechanical properties of mortar.
- Open Access
- 1 October 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (10) , 105001
Mechanical properties of nano SiO2 and fiber-reinforced concrete with steel fiber and high performance polypropylene fiber
- 1 October 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (10) , 105001
Open AccessMechanical properties of nano SiO2 and fiber-reinforced concrete with steel fiber and high performance polypropylene fiber
- Open Access
Mechanical Properties of Nano SiO2 and Carbon Fiber Reinforced Concrete after Exposure to High Temperatures
This study presents the key mechanical and residual properties after high-temperature of different Nano SiO2 carbon fiber-reinforced concrete (NSCFRC) mixtures. A total of seven NSCFRC mixtures incorporating 0%–0.35% of carbon fiber by volume of concrete and 0%–2% Nano SiO2 by weight of the binder were studied. The key mechanical properties such as compressive strength, tensile strength, and flexural strength of NSCFRC with 0.25% carbon fiber and 1% NS were 6.8%, 20.3%, and 11.7% higher than PC (0% CFs, 0% NS), respectively. Scanning Electron Microscopy (SEM) shows that Nano SiO2 reduced the internal porosity and increased the compactness of the concrete matrix. Furthermore, the experimental result demonstrates that NSCFRC can improve the mechanical properties of concrete after high-temperature and equations were obtained to describe the evolution of residual properties at elevated temperatures. Results suggested that the effect of carbon fibers on the residual properties of concrete after high-temperature is less than steel fiber and polypropylene fiber. It was also indicated that adding appropriate Nano SiO2 to concrete is an effective means to improve the residual performance after high-temperature.
Open AccessMechanical Properties of Nano SiO2 and Carbon Fiber Reinforced Concrete after Exposure to High Temperatures
This study presents the key mechanical and residual properties after high-temperature of different Nano SiO2 carbon fiber-reinforced concrete (NSCFRC) mixtures. A total of seven NSCFRC mixtures incorporating 0%–0.35% of carbon fiber by volume of concrete and 0%–2% Nano SiO2 by weight of the binder were studied. The key mechanical properties such as compressive strength, tensile strength, and flexural strength of NSCFRC with 0.25% carbon fiber and 1% NS were 6.8%, 20.3%, and 11.7% higher than PC (0% CFs, 0% NS), respectively. Scanning Electron Microscopy (SEM) shows that Nano SiO2 reduced the internal porosity and increased the compactness of the concrete matrix. Furthermore, the experimental result demonstrates that NSCFRC can improve the mechanical properties of concrete after high-temperature and equations were obtained to describe the evolution of residual properties at elevated temperatures. Results suggested that the effect of carbon fibers on the residual properties of concrete after high-temperature is less than steel fiber and polypropylene fiber. It was also indicated that adding appropriate Nano SiO2 to concrete is an effective means to improve the residual performance after high-temperature.
- 1 August 2017
- Published by Elsevier in Ceramics International
- Vol. 43 (12) , 9377-9381
Characterization and photocatalytic properties of SiO 2 –TiO 2 nanocomposites prepared through gaseous detonation method
- 1 August 2017
- Published by Elsevier in Ceramics International
- Vol. 43 (12) , 9377-9381
Characterization and photocatalytic properties of SiO 2 –TiO 2 nanocomposites prepared through gaseous detonation method
- 1 June 2017
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 194, 17-22
Synthesis of nano-TiO 2 with slurry explosives of different densities and spread calculation
- 1 June 2017
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 194, 17-22
Synthesis of nano-TiO 2 with slurry explosives of different densities and spread calculation
- 1 March 2017
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 17 (3) , 2124-2129
Optimal Design and Preparation of Nano-TiO2 Photocatalyst Using Gaseous Detonation Method
The effects of initial temperature, precursor dose, and molar ratio of precursor and hydrogen on TiO2 nanometer photocatalyst prepared through gaseous detonation were studied through orthogonal experiment and L(34) orthogonal array, and characterization was performed through X-ray diffraction and Transmission electron microscope. The particle size, morphology, and photocatalytic ability of the product are significantly influenced by preparation conditions. The photocatalytic ability of the product is highly affected by TiCl4 dose, followed by the initial temperature and molar ratio of the precursor and hydrogen. The product prepared at an initial temperature of 130 °C with 5 mL of TiCl4 and 1:1 ratio of TiCl4:H2 exhibits the highest photocatalytic activity and good crystallinity. The product is a mixed crystal of the anatase and rutile phases, with an anatase content of 29.38% and mean particle sizes of 36.93 (Anatase) and 43.95 nm (Rutile). The photocatalyst degradation rate of methyl orange solution reaches 95.82% after exposure to UV light for 40 min.
- 1 March 2017
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 17 (3) , 2124-2129
Optimal Design and Preparation of Nano-TiO2 Photocatalyst Using Gaseous Detonation Method
The effects of initial temperature, precursor dose, and molar ratio of precursor and hydrogen on TiO2 nanometer photocatalyst prepared through gaseous detonation were studied through orthogonal experiment and L(34) orthogonal array, and characterization was performed through X-ray diffraction and Transmission electron microscope. The particle size, morphology, and photocatalytic ability of the product are significantly influenced by preparation conditions. The photocatalytic ability of the product is highly affected by TiCl4 dose, followed by the initial temperature and molar ratio of the precursor and hydrogen. The product prepared at an initial temperature of 130 °C with 5 mL of TiCl4 and 1:1 ratio of TiCl4:H2 exhibits the highest photocatalytic activity and good crystallinity. The product is a mixed crystal of the anatase and rutile phases, with an anatase content of 29.38% and mean particle sizes of 36.93 (Anatase) and 43.95 nm (Rutile). The photocatalyst degradation rate of methyl orange solution reaches 95.82% after exposure to UV light for 40 min.
- 1 January 2017
- Published by Elsevier in Ceramics International
- Vol. 43 (1) , 1517-1521
Characterization and photocatalytic properties of SnO 2 –TiO 2 nanocomposites prepared through gaseous detonation method
- 1 January 2017
- Published by Elsevier in Ceramics International
- Vol. 43 (1) , 1517-1521
Characterization and photocatalytic properties of SnO 2 –TiO 2 nanocomposites prepared through gaseous detonation method
- 10 November 2016
- Published by Taylor & Francis in Phase Transitions
- Vol. 90 (6) , 618-627
Phase transition rate of anatase during detonation synthesis of TiO2
TiO2 powders were synthesized by two types of mixed explosives in a sealed reaction kettle. The phase and morphology of TiO2 powders were obtained by X-ray diffractometry and transmission electron microscopy. Results indicate that powders obtained from metatitanic acid contained mixed explosive are mixed crystal of anatase and rutile. The phase transition rate of anatase increases from 22.9% to 93.3% with the rise of mass ratio of hexogen, and the grain size also enlarges gradually. The powder obtained from anatase contained mixed explosive is rutile, and the phase transition rate of anatase is 100%. Compared with that before detonation, the grain size of anatase after detonation significantly changes, from nanoscale to micronscale. Based on the calculation of detonation parameters, the phase transition process and grain growth during the synthesis of TiO2 by means of detonation method are analyzed, and the nucleating collision–growth model is proposed.
- 10 November 2016
- Published by Taylor & Francis in Phase Transitions
- Vol. 90 (6) , 618-627
Phase transition rate of anatase during detonation synthesis of TiO2
TiO2 powders were synthesized by two types of mixed explosives in a sealed reaction kettle. The phase and morphology of TiO2 powders were obtained by X-ray diffractometry and transmission electron microscopy. Results indicate that powders obtained from metatitanic acid contained mixed explosive are mixed crystal of anatase and rutile. The phase transition rate of anatase increases from 22.9% to 93.3% with the rise of mass ratio of hexogen, and the grain size also enlarges gradually. The powder obtained from anatase contained mixed explosive is rutile, and the phase transition rate of anatase is 100%. Compared with that before detonation, the grain size of anatase after detonation significantly changes, from nanoscale to micronscale. Based on the calculation of detonation parameters, the phase transition process and grain growth during the synthesis of TiO2 by means of detonation method are analyzed, and the nucleating collision–growth model is proposed.
- 1 August 2016
- Published by IOP Publishing in Materials Research Express
- Vol. 3 (8) , 085012
Influence of TiCl4concentration on the photocatalytic performance of nano-TiO2synthesized by gaseous detonation
- 1 August 2016
- Published by IOP Publishing in Materials Research Express
- Vol. 3 (8) , 085012
Influence of TiCl4concentration on the photocatalytic performance of nano-TiO2synthesized by gaseous detonation