HJHyeon-Gu Jeon

Hyeon-Gu Jeon

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hyeon-Gu Jeon has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • 機械学習による電気トリーイング現象画像の認識と分類

    by Yudai Shiozaki, Hyeon-Gu Jeon, Haruo Ihori

    The electrical tree is degradation traces of insulating materials. The mechanism of this electrical tree progress is not yet understood. Therefore, we wondered if machine learning could be used to elucidate the progress mechanism. First, we investigated the applicability of machine learning to electrical tree.

  • Measurement of electrical resistance of thermoelectric materials with a temperature gradient using instant load-voltage analysis

    by Hyeon-Gu Jeon, Jae Yong Song, Byungsung O, Yong-Gyoo Kim

    Among the properties of thermoelectric materials, electrical conductivity can be evaluated by measuring the resistance experimentally. However, thermoelectric materials have a high thermoelectric voltage due to their high Seebeck coefficient, which can cause measurement errors when using the four-wire method. This paper describes a new method for measuring the resistance of thermoelectric materials using temperature gradient. This method, instant load-voltage analysis (ILA), allows for measurement of the resistance of thermoelectric materials using the voltage induced by the Seebeck effect. The test sample was prepared with type E thermocouples, which have well-defined thermoelectric voltage with temperature. One side of the sample was kept at 20 °C; then the resistance was measured using the ILA method by increasing the temperature of the other side from 30 °C to 90 °C. The Fin model, a well-known heat transfer model, was used to determine the temperature of the sample with a temperature gradient. The measurement results were compared with the reference resistances measured by the four-wire method under constant temperature conditions. From the comparison, the sample resistance measured using the ILA method showed a good agreement (±0.2%) with the reference value.


  • Organic Photodiode with High Infrared Light Sensitivity Based on Tin Phthalocyanine/C60 Bulk Heterojunction and Optical Interference Effect

    by Musubu Ichikawa, Toshiki Takeuchi, Hyeon-Gu Jeon, Yongwan Jin, Sangyoon Lee, Kyu-Sik Kim

    We demonstrated an organic near-infrared (NIR) photodiode on the basis of the bulk heterojunction (BHJ) structure by using tin phthalocyanine (SnPc) and C60 fullerene with a high incident photon–electron conversion efficiency (IPCE) of 50% at a wavelength of 750 nm. The cell showed optical responses to about 1000 nm and had a specific detectivity D * of 1.59 ×1011 cm Hz1/2/W. The SnPc:C60 ratio in the BHJ layer influenced the optical response. Higher ratios enhanced NIR sensitivity but reduced the peak IPCE; the optimal ratio was 3:1. The optical interference of directly incident light and light reflected from an Al electrode was also examined to enhance the IPCE at longer wavelengths. With a 90-nm-thick C60 layer, the first antinode of the standing wave at a wavelength of 750 nm was located at the BHJ layer; this layer enhanced the IPCE at 700 and 800 nm but reduced it at 400 nm.


  • Open Access

    Effects of volatile additives in solutions used to prepare polythiophene-based thin-film transistors

    by Musubu Ichikawa, Kenta Yamamura, Hyeon-Gu Jeon, Miyako Nakajima, Yoshio Taniguchi

    We investigate the effects of volatile additives in solutions used to prepare thin-film transistors (TFTs) of regioregular poly(3-hexylthiophene) (P3HT). We use the additives trifluoromethylbenzene (TFMB) and methylcyclohexane (MCH) because they are poor solvents for P3HT. The additives improve the performance of the resulting TFTs when the boiling point (Tb) of the major solvent, carbon tetrachloride, is lower than that of the additive. The maximum mobility is (4.0 ± 0.9) × 10–2 cm2V–1s–1, which is 6.1 times larger than that of TFTs prepared without TFMB or MCH added to the solution; the on/off ratio and the subthreshold slope were also improved. The relative Tb of the solvent and the additive affected the film formation with the amount of TFMB or MCH remaining at the final stage of thin film deposition influencing the precipitation of P3HT aggregates.