Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Adam Piechna has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of hydrodynamic and functional nonlinearities of blood flow in the cerebral vasculature on cerebral perfusion and autoregulation pressure reserve

    by Adam Piechna, Krzysztof Cieślicki

    Ensuring the transport of oxygenated blood to the brain is one of the priorities of the human body. In the literature, there are many models of cerebral circulation with different levels of complexity used to assess pathological conditions, support clinical decisions, and learn about the relationships governing cerebral circulation. This paper presents a zero-dimensional cerebral circulation model that considers hydrodynamic nonlinearities and autoregulation mechanisms. The model has been verified using a computational fluid dynamics (CFD) model of the Circle of Willis (CoW) and its supplying and outgoing branches. Despite the considerable simplicity, the presented model captured the dominant features of cerebral circulation and provides good agreement with the CFD model. The errors in relation to the CFD model did not exceed 2.6% and 9.9% for the symmetrical and highly asymmetrical CoW configurations, respectively. The practical application of the model was demonstrated for predicting the autoregulation pressure reserve for different diameters of natural anastomoses: Posterior and Anterior Communicating Arteries. The advantages and limitations of the model were discussed.


  • Open Access

    CFD Model of a Mechanical Oscillator Flowmeter

    by Maciej Szudarek, Mateusz Turkowski, Adam Piechna

    Most of the studies on mechanical oscillator flowmeters were conducted in the ‘80s and ‘90s when computational fluid dynamics (CFD) was not a viable scientific tool in flow metrology. Still, many topics related to the application of mechanical oscillator flowmeters require further investigation. In the article, a numerical model of a mechanical oscillator flowmeter is developed with the commercial software ANSYS Fluent. The model is validated against experimental data obtained at a water calibration stand. The influence of the selected turbulence model, dynamic mesh method, as well as grid and time step size is studied. The model’s qualitative behavior is correct, allowing investigation into the flowmeter operation in detail. It can provide a base for the improvement of the flowmeter’s performance. Relative differences in the frequency of oscillations did not exceed 4% for a DN50 flowmeter in the flow rate range (2–40) m3/h.


  • Open Access

    CFD Study of High-Speed Train in Crosswinds for Large Yaw Angles with RANS-Based Turbulence Models including GEKO Tuning Approach

    by Maciej Szudarek, Adam Piechna, Piotr Prusiński, Leszek Rudniak

    Crosswind action on a train poses a risk of vehicle overturning or derailment. To assess if new train designs fulfill the safety requirements, computational fluid dynamics is commonly used. This article presents a comprehensive wind flow analysis on an example of a TGV high-speed train. Large yaw angle range is studied with the application of widely used Reynolds-averaged Navier–Stokes (RANS) turbulence models. The predictive performance of popular RANS-based models in that regime has not been reported extensively before. The context of simulations is a study of crosswind stability using methodology presented in norm EN 14067-6:2018. It is shown that for yaw angles up to 45 degrees, aerodynamic forces predicted by all the studied RANS-based models are consistent with experimental data. At larger yaw angles, flow structure becomes complicated, separation lines are no longer defined by geometry, and significant discrepancies between turbulence models appear, with relative differences between models up to 30%. A detailed study was performed to investigate differences between turbulence models for specific angles of 40, 60, and 80 degrees, which correspond to distinctive ranges of moment characteristics. Finally, a successful attempt was made to tune a GEKO turbulence model to fit the experimental data. This allowed us to reduce the maximum relative error in comparison to the experiment in the full yaw angles range down to 12.7%, which is in line with the norm requirements.


  • Open Access

    Comprehensive CFD Aerodynamic Simulation of a Sport Motorcycle

    by Krzysztof Wiński, Adam Piechna

    Nowadays, aerodynamics is a key focal point in the vehicle design process. Beyond its direct impact on the performance of a vehicle, it also has significant effects on economics and safety. In the last decade numerical methods, mainly Computational Fluid Dynamics (CFD), have established themselves as a reliable tool that assists in the design process and complements classical tunnel tests. However, questions remain about the possible obtained accuracy, best practices and applied turbulence models. In this paper, we present a comprehensive study of motorcycle aerodynamics using CFD methods which, compared to the most common car aerodynamics analysis, has many specific features. The motorcycle, along with its rider, constitutes a shape with very complex aerodynamic properties. A detailed insight into the flow features is presented with detailed commentary. The front fairing, the front wheel and its suspension were identified as the main contributors to the aerodynamic drag of the motorcycle and its rider. The influence of rider position was also studied and identified as one of the most important elements when considering motorcycle aerodynamics. An extensive turbulence models study was performed to evaluate the accuracy of the most common Reynolds-averaged Navier–Stokes models and novel hybrid models, such as the Scale Adaptive Simulation and the Delayed Detached Eddy Simulation. Similar values of drag coefficients were obtained for different turbulence models with noticeable differences found for k−ϵ models. It was also observed that near-wall treatment affects the flow behaviour near the wheels and windshield but has no impact on the global aerodynamic parameters. In the summary, a discussion about the obtained results was set forth and a number of questions related to specifics of motorcycle CFD simulations were addressed.


  • Open Access

    Feasibility Study of a Fan-Driven Device Generating Downforce for Road Cars

    by Maciej Szudarek, Adam Piechna, Janusz Piechna

    This paper, submitted to the special issue of Energies “Future of Road Vehicle Aerodynamics”, proposes and justifies the use of an old idea of generating downforce by actively drawing air from under the car body and exhausting it to the outside. Instead of traditional moving mechanical-curtain elements, a new method for sealing the clearance under the body with an air curtain is proposed. Basic information on the geometry and flow characteristics of such a solution suitable for use in automobiles is presented. The performance of such a fan-driven device generating downforce is studied over a wide range of driving speeds. The device allows for significantly improved vehicle acceleration, shorter braking distances, and extension of the range of safe cornering speeds. The paper shows the successive stages of development of the idea, from the 2D model to the 3D model, and an attempt to implement the device on a sports car. The distributions of pressure, velocity, pathlines and values of aerodynamic forces obtained at assumed fan compressions for different driving speeds are presented. The advantages and disadvantages of the analyzed device are discussed, and further optimization directions are outlined.


  • Open Access

    Influence of the Car Movable Aerodynamic Elements on Fast Road Car Cornering

    by Janusz Ryszard Piechna, Krzysztof Kurec, Jakub Broniszewski, Michał Remer, Adam Piechna, Konrad Kamieniecki, Przemysław Bibik

    In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.


  • Open Access

    Reversed Robin Hood Syndrome in the Light of Nonlinear Model of Cerebral Circulation

    by A. Piechna, K. Cieslicki

    The brain is supplied by the internal carotid and vertebro-basilar systems of vessels interconnected by arterial anastomoses and forming at the base of the brain a structure called the Circle of Willis (CoW). An active intrinsic ability of cerebral vascular bed maintains constant Cerebral Blood Flow (CBF) in a certain range of systemic pressure changes. This ability is called autoregulation and together with the redundant structure of the CoW guarantee maintaining CBF even in partial occlusion of supplying arteries. However, there are some situations when the combination of those two mechanisms causes an opposite effect called the Reversed Robin Hood Syndrome (RRHS). In this work we proposed a model of the CoW with autoregulation mechanism and investigated a RRHS which may occur in the case of Internal Carotid Artery (ICA) stenosis combined with hypercapnia. We showed and analyzed the mechanism of stealing the blood by the contralateral side of the brain. Our results were qualitatively compared with the clinical reports available in the literature.


  • Age dependence of critical pressure in the segments and branches of the circle of Willis

    by Adam Piechna, Leszek Lombarski, Paweł Krajewski, Bogdan Ciszek, Krzysztof Cieslicki

    Spontaneous intracranial haemorrhage is one of the most dramatic neurological disasters. The source of haemorrhage is linked to the pathology of the arterial wall or is unknown. Because the risk of haemorrhagic stroke increases with age, we tried to investigate the relationship between age and rupture pressure of cerebral arteries. In the presented study, 51 segments of large cerebral arteries (at the level of the circle of Willis and its incoming and outgoing branches) were obtained from 33 cadaver brains aged 12-86 years. The segments were pressurized up to the rupture. The rupture pressure was noted. The highest observed pressure was 4.3atm in specimen aged 24 years. The lowest pressure 1.19atm was observed in specimen aged 80 years. The mean value of rupture pressure of all investigated segments was 2.28atm. Statistical analysis showed a nonlinear exponential decrease of the rupture pressure of the large cerebral arteries with age. The main conclusion from our study is that drop of cerebral arteries strength is observed to the age of 40. Later this lowering is visible but not so evident.


  • Experimental determination of rupture pressure and stress of adventitia of human middle cerebral arteries

    by Adam Piechna, Leszek Lombarski, Bogdan Ciszek, Krzysztof Cieslicki

    Background: Intracranial arterial dissections might be attributed to the particular biomechanical properties of their specific layers. Also, knowledge of adventitia properties would be crucial in the context of intracranial balloon angioplasty. Aims: The purpose of this work was to determine the rupture pressure of separated adventitia and compare it to intact cerebral arterial segments. Methods: Brain specimens were harvested from 14 autopsy subjects (age range from 23 to 86 years). Pressure-inflation tests were conducted on proximal segments of middle cerebral arteries and separated adventitia layers from contralateral arteries to assess the rupture pressure values. Results: The averaged rupture pressure of adventitia layers was 1.41 SD 0.25 atm (1072 SD 190 mmHg), whereas for intact arterial segments it was 2.32 SD 0.70 atm (1763 SD 532 mmHg) and diminished with age according to nonlinear regression trends. The difference beetween the aformentioned rupture pressures was positively correlated with rupture pressure of intact arterial segments ( R2 = 0.88; p < 0.001). Conclusions: The obtained experimental results indicate a leading role of adventitia in building arterial strength under supraphysiological pressure conditions. The greater the rupture pressure of complete cerebral arteries, the smaller the contribution of adventitia in overall wall resistance.